• Journal of the Korean institute of surface engineering
• /
• v.49 no.3
• /
• pp.252-259
• /
• 2016

In order to form an aluminum-doped zinc oxide (AZO) transparent electrode film on a polyethylene terephthalate (PET) substrate used for a flexible display substrate, the AZO transparent electrode was produced at low temperature without substrate heating. Even though the produced electrode showed characteristic optical transmittance of 90 % (at 550 nm) and sheet resistance within $100{\Omega}/sq$, cracks occurred 10 minutes after loading applied 2 mm radius of curvature, and the sheet resistance increased linearly. An insertion layer of ZrCu was formed between the AZO film and the PET substrate to suppress the generation of cracks on the AZO film. It was verified that the crack was not generated 30 minutes after the loading of 2 mm radius of curvature, and no increase in sheet resistance was recorded. There was also not cracks in the dynamic bending test of 4 mm radius, but surface resistance was slightly increased. As a result, the ZrCu insertion film improved the interfacial adhesion between the substrate and AZO film layer without increasing sheet resistance and decreasing transmittance.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1425_1426
• /
• 2009

In this study, commercially available polyethylene terephthalate(PET), which is widely used as a substrate of flexible electronic devices, was modified by dielectric barrier discharge(DBD) method in an air condition at atmospheric pressure, and aluminium - doped zinc oxide (ZnO:Al) transparent conducting film was deposited on PET substrate by r. f. magnetron sputtering method. Surface analysis and characterization of the plasma-treated PET substrate was carried out using contact angle measurements, X-ray Photoelectron Spectroscopy(XPS) and Atomic Force Microscopy (AFM). Especially the effect of surface state of PET substrate on some important properties of ZnO:Al transparent conducting film such as electrical and morphological properties and deposition rate of the film, was studied experimentally. The results showed that the contact angle of water on PET film was reduced significantly from $62^{\circ}$ to $43^{\circ}$ by DBD surface treatment at 20 min. of treatment time. The plasma treatment also improved the deposition rate and electrical properties. The deposition rate was increased almost linearly with surface treatment time. The lowest electrical resistivity as low as $4.97{\times}10^{-3}[\Omega-cm]$ and the highest deposition rate of 234[${\AA}m$/min] were obtained in ZnO:Al film with surface treatment time of 5min. and 20min., respectively.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.12 no.2 s.27
• /
• pp.225-235
• /
• 1988

The effects of surface free energy of substrates on the soiling and on the detergency of the oily soil were studied. The surface tension consisted of dispersion force and polar force components of substrate, oily soil and surfactant solutions were calculated by extended Fowkes' equation. From these values, work of adhesion($W_a$), work of detergency($W_D$), ana residual work of detergency($W_{D,R}$) were calculated. The correlations between these theoretical values of the works and detergency were discussed. MAA grafted PET film was used as substrate, triolein as oily soil and nonylphenol polyoxyethylene ether(NPE) having various mole numbers of oxyethylene adducts and dodecylbenzene sulfonate (DBS) as surfactants. Detergency was estimated by means of radioactive tracer method using $C^{14}-triolein$. The results showed that $W_a$ was decreased with the increase of surface free energy of substrate. In water, $W_D\;and\;W_{D,R}$ were decreased and detergency of tiolein was increased with the increase of surface free energy of substrate. In surfactant solutions, the lower the surface free energy of substrate and the lower oxyethylene adducts of NPE were the more effective on detergency. The detergency of DBS solution was the lowest in the case of ungrafted PET film, but even small increase in surface free energy by grafting showed much increase in detergency.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.6
• /
• pp.1799-1805
• /
• 2014

In this article, we described about the preparation and electrochemical properties of a flexible energy storage system based on a plastic polyethylene terephthalate (PET) substrate. The PET treated with UV/ozone was fabricated with multilayer films composed of 30 polyaniline (PANi)/graphene oxide (GO) bilayers using layer-by-layer assembly of positively charged PANi and negatively charged GO. The conversion of GO to the reduced graphene oxide (RGO) in the multilayer film was achieved using hydroiodic acid vapor at $100^{\circ}C$, whereby PANi structure remained nearly unchanged except a little reduction of doping state. Cyclic voltammetry and charge/discharge curves of 30 PANi/RGO bilayers on PET substrate (shorten to PANi-$RGO_{30}$/PET) exhibited an excellent volumetric capacitance, good cycling stability, and rapid charge/discharge rates despite no use of any metal current collectors. The specific capacitance from charge/discharge curve of the PANi-$RGO_{30}$/PET electrode was found to be $529F/cm^3$ at a current density of $3A/cm^3$, which is one of the best values yet achieved among carbon-based materials including conducting polymers. Furthermore, the intrinsic electrical resistance of the PANi-$RGO_{30}$/PET electrodes varied within 20% range during 200 bending cycles at a fixed bend radius of 2.2 mm, indicating the increase in their flexibility by a factor of 225 compared with the ITO/PET electrode.

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.1
• /
• pp.7-12
• /
• 2014

In this study, we investigate the effects of corona-discharge pre-treatment on the properties of carbon nanotubes (CNTs) which are used as flexible transparent electrodes. The CNTs are deposited on PET (polyethylene terephthalate) substrates using a spray coating method. Prior to the deposition of CNTs, the PET substrates are corona-treated by varying the feeding directions of the PET substrate and the numbers of treatments. The variations in the surface morphologies and roughnesses of the PET substrates due to corona-treatment are characterized via atomic force microscopy (AFM). Dynamic contact angles (DCAs) of the corona-treated PET substrates are measured and analyzed as functions of the treatment conditions. Also, the sheet resistances and visible-range transmittances of the CNTs deposited on PET substrates are measured before and after bending test. The experimental results obtained in this study provide strong evidences that the adhesive forces between CNTs and PET substrates can be substantially enhanced by corona-discharge pretreatment.

• Textile Coloration and Finishing
• /
• v.11 no.1
• /
• pp.25-33
• /
• 1999

PET fabric was grafted with $CF_4$ or $C_2F_6$ plasmas generated by glow discharge. The water repellency of plasma-treated fabrics were evaluated with contact angle meter. The change in surface morphologies was observed by SEM, and the change of surface chemical characteristics were analyzed by FT-IR, ESCA and microchemical analysis technique. The results obtained are as follows : 1) The contact angle of plasma-treated fabric was over $150^\circ{C}$. 2) It was observed by SEM that the surface of treated substrate was over coated with thin film formed by the fluorocarbon plasma treatment. 3) According to ESCA analysis, there were prevailing -CHF-, $-CF_2$- and a little $-CF_3$ components on fluorocarbon plasma treated substrate. -CHF- and $-CF_2$- components were reduced by washing, and $-CF_2$- component was recovered by heat treatment. 4) In consideration of quantitative analysis of fluorine and F/C ratio by ESCA, we found that fluorination reached to the inner of substrate.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1457-1458
• /
• 2011

PET 기판은 소수성이므로 용액 성장법(CBD)으로 CdS 박막을 성장시키기 어렵다. 이런 단점을 극복하기 위하여 기판으로 사용할 PET의 표면을 산소 분위기에서 IPC로 개질하여 실험한 결과 CdS 박막을 성공적으로 성장시킬 수 있었다. 개질된 PET 기판의 접촉각과 표면 거칠기 등을 관찰하였으며, 성장된 CdS 박막의 SEM 분석 등을 통하여 개선된 특성을 확인하였다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.41-43
• /
• 2004

Plasma polymerized para-xylene ($PP_PX$) deposited by plasma-enhanced chemical vapor deposition (PECVD) was used as the barrier layer on the polyethylene terephthalate (PET) substrate to improve lifetime of the flexible organic light-emitting diodes (FOLEDs). The $PP_PX$ barrier layer deposited on top of the PET substrate with plasma power of 30 W at deposition pressure of 0.2 torr showed transmittance spectra good enough to be applied in FOLED on PET substrates. FOLEDs with the $PP_PX$ barrier layer (barrier-FOLEDs) showed similar I-V and B-V characteristics to FOLEDs without the $PP_PX$ layer (control-FOLEDs). The lifetime of barrier-FOLED was two times longer than that of the control-FOLED. With $PP_PX$ passivation layers, lifetimes of both control and barrier-FOLEDs were improved by more than 4 times. These results show that PECVD deposited $PP_PX$ layers can be used as barrier layers for FOLEDs on plastic substrates as well as passivation layers for general OLEDs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.10-10
• /
• 2009

We have fabricated transparent and flexible thin film transistor(TFT) on polyethylene terephthalate(PET) substrate using Zinc Oxide (ZnO) and Indium Tin Oxide (ITO) film as active layer and electrode. The transfer printing method was used for printing the device layer on target plastic substrate at room temperature. This approach have an advantage to separate the high temperature annealing process to improve the electrical properties of ZnO TFT from the device process on plastic substrate. The resulting devices on plastic substrate presented mechanical and electrical properties similar with those on rigid substrate.

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.3
• /
• pp.122-125
• /
• 2004

ITO films were deposited on polyethylene terephthalate substrate by a dc reactive magnetron sputtering using rf bias without substrate heater and post-deposition thermal treatment. The dependency of rf substrate bias on plasma sputter processing was investigated to control energetic particles and improve ITO film properties. The substrate was applied negative rf bias voltage from 0 to -80 V. The composition of indium, tin, and oxygen atoms is strongly depended on the rf substrate bias. Oxygen deficiency is the highest at rf bias of -20 V. The electrical and optical properties of ITO films also are dominated obviously by negative rf bias.