• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.157-158
• /
• 2007

Effects of post-metallization anneal (PMA) on interface trap characteristics of Si-$SiO_2$ are studied. The conventional PMA method utilizes forming gas anneal, where 10% hydrogen in nitrogen atmosphere is used. A new PMA method utilizes hydrogen rich PECVD- silicon nitride $(SiN_x)$ film as a hydrogen diffusion source and a out-diffusion blocking layer. It can be shown through charge pumping current measurement that the new PMA is indeed effective to decrease Si-$SiO_2$ interface trap density.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.430-430
• /
• 2008

Using multi plasma enhanced chemical vapor deposition system (Multi-PECVD), p-a-Si:H deposition layer as a $p^+$ region which was annealed by laser (Q-switched fiber laser, $\lambda$ = 1064 nm) on an n-type single crystalline Si (100) plane circle wafer was prepared as new doping method for single crystalline interdigitated back contact (IBC) solar cells. As lots of earlier studies implemented, most cases dealt with the excimer (excited dimer) laserannealing or crystallization of boron with the ultraviolet wavelength range and $10^{-9}$ sec pulse duration. In this study, the Q-switched fiber laser which has higher power, longer wavelength of infrared range ($\lambda$ = 1064 nm) and longer pulse duration of $10^{-8}$ sec than excimer laser was introduced for uniformly deposited p-a-Si:H layer to be annealed and to make sheet resistance expectable as an important process for IBC solar cell $p^+$ layer on a polished n-type Si circle wafer. A $525{\mu}m$ thick n-type Si semiconductor circle wafer of (100) plane which was dipped in a buffered hydrofluoric acid solution for 30 seconds was mounted on the Multi-PECVD system for p-a-Si:H deposition layer with the ratio of $SiH_4:H_2:B_2H_6$ = 30:120:30, at $200^{\circ}C$, 50 W power, 0.2 Torr pressure for 20 minutes. 15 mm $\times$ 15 mm size laser cut samples were annealed by fiber laser with different sets of power levels and frequencies. By comparing the results of lifetime measurement and sheet resistance relation, the laser condition set of 50 mm/s of mark speed, 160 kHz of period, 21 % of power level with continuous wave mode of scanner lens showed the features of small difference of lifetime and lowering sheet resistance than before the fiber laser treatment with not much surface damages. Diode level device was made to confirm these experimental results by measuring C-V, I-V characteristics. Uniform and expectable boron doped layer can play an important role to predict the efficiency during the fabricating process of IBC solar cells.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.128-128
• /
• 2010

중적외선 영역은 장애물에 의해서 파장의 흡수가 거의 일어나지 않기 때문에 적외선 소자에서 널리 이용되고 있다. 현재 대부분의 중적외선 소자에는 HgCdTe (MCT)가 사용되고 있지만, 3성분계 화합물이 가지는 여러 문제를 가지고 있다. 반면에, 2성분계 화합물인 인듐안티모나이드 (InSb)는 중적외선 영역 ($3-5\;{\mu}m$) 파장 대에서 HgCdTe와 대등한 소자 특성을 나타냄과 동시에 낮은 기판 가격, 소자 제작의 용이성, 그리고 야전과 우주 공간에서 소자 동작의 안정성 때문에 HgCdTe를 대체할 물질로 주목을 받고 있다. InSb는 미국과 이스라엘과 같은 일부 선진국을 중심으로 연구가 되었지만, 국방 분야의 중요한 소자로 인식되었기 때문에 소자 제작에 관한 기술적인 내용은 국내에 많이 알려지지 않은 상태이다. 따라서 본 연구에서는 InSb 소자 제작의 기초연구로 절연막과 pn 접합 형성에 대한 연구를 수행하였다. 절연막의 특성을 알아보기 위해, InSb 기판위에 $SiO_2$와 $Si_3N_4$를 PECVD (Plasma Enhanced Chemical Vapor Deposition)로 증착을 하였다. 절연막의 계면 트랩 밀도는 77K에서 C-V (Capacitance-Voltage) 분석을 통하여 계산하였으며, Terman method 방법을 이용하였다.[1] $SiO_2$는 $120-200^{\circ}C$의 온도 영역에서 계면 트랩 밀도가 $4-5\;{\times}\;10^{11}cm^{-2}$범위를 가진 반면, $240^{\circ}C$의 경우 계면 트랩 밀도가 $21\;{\times}\;10^{11}cm^{-2}$로 크게 증가하였다. $Si_3N_4$는 $SiO_2$ 절연막에 비해서 3배 정도의 높은 계면 트랩 밀도 값을 나타내었으며. Remote PECVD 장비를 이용하여 $Si_3N_4$ 절연막에 관한 연구를 추가적으로 진행하여 $7-9\;{\times}\;10^{11}cm^{-2}$ 정도의 계면 트랩 밀도 값을 구할 수가 있었다. 따라서 InSb에 대한 절연막은 $200^{\circ}C$ 이하에서 증착된 $SiO_2$와 Remote PECVD로 증착 된 $Si_3N_4$가 적합하다고 할 수 있다. 절연막 연구와 더불어 InSb 소자의 pn 접합 연구를 진행하였다. n-InSb (100) 기판 ($n\;=\;0.2-0.85\;{\times}\;10^{15}cm^{-3}$ @77K)에 $Be^+$이온 주입하여 p층을 형성하여 제작 되었으며, 열처리 조건에 따른 소자의 특성을 관찰 하였다. $450^{\circ}C$에서 30초 동안 RTA (Rapid Thermal Annealing)공정을 진행한 샘플은 -0.1 V에서 $50\;{\mu}A$의 높은 암전류가 관찰되었으며, 열처리 조건을 60, 120, 180초로 변화하면서 소자의 특성 변화를 관찰하였다.

• Journal of Satellite, Information and Communications
• /
• v.6 no.1
• /
• pp.28-31
• /
• 2011

In this paper, a new set of structural and sacrificial material that is diamond like carbon (DLC)/photoresist for high performance piezoelectric RF-MEMS switches which are actuated in d33 mode is suggested. To avoid curing problem of photoresist sacrificial layer, DLC structure layer is deposited at room temperature by radio frequency plasma enhanced chemical vapor deposition (RF-PECVD) method. And lead zirconate titanate (PZT) piezoelectric layer is deposited on structure layer directly at room temperature by rf magnetron sputtering system and crystallized by rapid thermal annealing (RTA) equipment. Particular attention is paid to the annealing of PZT film in order to crystallize into perovskite and the variation of mechanical properties of DLC layer as a function of annealing temperature. The DLC layer shows good performance for structure layer in aspect to Young's modulus and hardness. The fabrication becomes much simpler and cheaper with use of a photoresist.

• Journal of Sensor Science and Technology
• /
• v.4 no.2
• /
• pp.58-63
• /
• 1995

The effects of substrate temperature, RF power, and $NH_{3}/SiH_{4}$ gas flow ratio on the dielectric constant and optical bandgap of amorphous silicon nitride (a-SiNx:H) thin films prepared by PECVD method using RF glow discharge decomposition of $SiH_{4}$ and $NH_{3}$ gas mixtures have been studied. The dielectric constant and optical bandgap of a-SiNx:H thin films were greatly exchanged as by increasing substrate temperature, RF power, and $NH_{3}/SiH_{4}$ gas flow ratio. The dielectric constant of a-SiNx:H films was increased and optical bandgap of a-SiNx:H films was decreased as the substrate temperature was increased. When the substrate temperature, RF power, gas pressure, $NH_{3}/SiH_{4}$ gas flow ratio, and thickness were $250^{\circ}C$, 20 W, 500 mTorr, 10 and $1500\;{\AA}$, respectively, the dielectric constant, breakdown field and optical bandgap of a-SiNx:H film were 4.3, 1 MV/cm, and 2.9 eV, respectively.

• Applied Chemistry for Engineering
• /
• v.20 no.5
• /
• pp.536-541
• /
• 2009

Plasma-polymerized acrylic acid films were deposited on Si wafer and KBr pellet by remote plasma-enhanced chemical vapor deposition (PECVD). Effects of plasma power, reaction pressure, indirect plasma method on the growth rate, chemical structure, and chemical bonding state of the films were investigated. Chemical structure and chemical state of the films were characterized by Fourier transformed infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy (XPS) analysis and curve fitting technique. Growth rate of the film increased to a saturation value with plasma power of 100 W, but showed the maximum with reaction pressure at 300 mtorr. Whenever W/FM factor (applied energy per gas molecule) increased by increasing plasma power or lowering pressure, the fragmentation of acrylic acid molecules was promoted. From the XPS curve fitting analyses, we found that the intensity of carboxyl COO bonding peak decreased with W/FM factor, and the tendency of intensity change of carboxylic COO peak was contrary to those of ether C-O and carbonyl C=O peaks.

• Journal of Korean Ophthalmic Optics Society
• /
• v.5 no.2
• /
• pp.193-199
• /
• 2000

The a-C : H films have been grown on the glass substrate by PECVD method, where plasma was generated with a 60 Hz line power source. The growth rate of films is found to be dependent of the partial pressure of $C_2H_2$. This growth rate is a little higher than that in which $CH_4$ instead of $C_2H_2$ is used. The transmittance is also much higher(95%). The optical energy gap of films is in the range of 1.4~1.8eV depending on the partial pressure of $C_2H_2$. However, this energy gap, which is 1.8eV, is found to be independent of the partial pressure of $C_2H_2$ for the thick films above $2000{\AA}$. The carbonization is checked from peak intensities of D ($sp^3$) and G($sp^2$) peaks in Roman spectra. The hydronization and C-H bonding status in films can also be determined from FTIR results. Both the bonding strength of C-H and the ratio of $sp^3$ to $sp^2$ in bonding are found to be slightly dependent of partial pressure of $C_2H_2$. Judging from above results, we can conclude that the best value for partial pressure of $C_2H_2$ in growing process of thick films is about 13.8%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.315-315
• /
• 2007

본 논문에서는 DLC (Diamond-like carbon)박막이 가지는 높은 경도, 낮은 마찰계수, 전기적 절연성, 화학적 안정성 등의 특성을 이용하여, 리소그래피를 위한 resist나 hard coating물질로써 응용하기 위해, DLC 박막의 에칭에 관한 연구를 진행하였다. DLC 박막의 합성 과 에칭은 13.56 MHz RF plasma enhanced vapor deposition technique를 통해 이루어졌으며, DLC 박막은 150 W의 RF Power에서 메탄 $(CH_4)$과 수소$(H_2)$ 가스를 이용하여 약 300 nm의 두께로 제작되었으며, DLC박막의 에칭은 RF power의 변화 (50~250 W)와 산소 $(O_2)$가스의 유량변화 (5~25 sccm)에 따라 실시하였다. 에칭 되어진 DLC 박막의 표면 특성들은 AFM (atomic force microscopy)과 contact angle 장치를 사용하여 측정되었고, 측정된 결과로써 DLC 박막은 RF power와 산소 가스의 유량이 높을수록 etching rate는 증가하였고, 박막의 표면은 거칠어졌으며, 결국 DLC 표면에서는 산소에 의한 결합의 증가로 인해 친수성을 나타내었다.

• Korean Journal of Materials Research
• /
• v.22 no.10
• /
• pp.552-561
• /
• 2012

Diamond-like carbon (DLC) films have been widely used in many industrial applications because of their outstanding mechanical and chemical properties like hardness, wear resistance, lubricous property, chemical stability, and uniformity of deposition. Also, DLC films coated on paper, polymer, and metal substrates have been extensively used. In this work, in order to improve the printing quality and plate wear of polymer printing plates, different deposition conditions were used for depositing DLC on the polymer printing plates using the Pulsed DC PECVD method. The deposition temperature of the DLC films was under $100^{\circ}C$, in order to prevent the deformation of the polymer plates. The properties of each DLC coating on the polymer concave printing plate were analyzed by measuring properties such as the roughness, surface morphology, chemical bonding, hardness, plate wear resistance, contact angle, and printing quality of DLC films. From the results of the analysis of the properties of each of the different DLC deposition conditions, the deposition conditions of DLC + F and DLC + Si + F were found to have been successful at improving the printing quality and plate wear of polymer printing plates because the properties were improved compared to those of polymer concave printing plates.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.540-540
• /
• 2013

In this studying, we investigated the basic properties of N-doped plasma polymer. The N-doped ethylcyclohexane plasma polymer thin films were deposited by radio frequency (13.56 MHz) plasma-enhanced chemical vapor deposition method. Ethylcyclohexenewas used as organic precursor (carbon source) with hydrogen gas as the precursor bubbler gas. Additionally, ammonia gas [NH3] was used as nitrogen dopant. The as-grown polymerized thin films were analyzed using ellipsometry, Fourier-transform infrared [FT-IR] spectroscopy, Raman spectroscopy, FE-SEM, and water contact angle measurement. The ellipsometry results showed the refractive index change of the N-doped ethylcyclohexene plasma polymer film. The FT-IR spectrashowed that the N-doped ethylcyclohexene plasma polymer films were completely fragmented and polymerized from ethylcyclohexane.