• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.6
• /
• pp.1-8
• /
• 1994

To enhance the strength of gears for transmission, Generally caburizing heat treatment is applied. But there are some problems in this technology the distortion of gears during heat treatment process, and the discontinuity of manufacturing process. For these reasons, the high frequency induction hardening process is widely used. This method is one of the surface hardening process to improve the wear resistance and fatigue life of the machine components. In this study, to compare the bending fatigue strength of caburized gear with that of induction hardened gear, bending fatigue testing of gears with two different cases was performed by using an electrohydraulic servo-controlled fatigue testing machine and double tooth bending fatigue test fixture. Fatigue life distributions at constant stress levels were established directly from fatigue data. For gear design, the fatigue strength distribution at specified life is more important. This distribution is obtained by statical transformation from fatigue life distribution. Reliability of bending fatigue strength was estimated by P-S-N curves and Weibull distribution.

• Analytical Science and Technology
• /
• v.18 no.6
• /
• pp.453-459
• /
• 2005

Phenol compounds in water were simultaneously analyzed by extractive derivatization. Aqueous solution was controlled to pH 13 with sodium hydroxide, and then $500{\mu}L$ of benzoyl chloride was added to the solution. The solution was shaken for 15 minutes and extracted with diethyl ether and then analyzed using GC/MS-SIM. The calibration curves of phenolic compounds in the range of 0.05 to $5.0{\mu}g/mL$ showed a good linearity having the correlation coefficient of $r^2=0.9915$ and standard deviation of ${\leq}8.5%$, respectively. The recoveries by this method ware 58.4-114.0%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.136-139
• /
• 1999

The post-annealing treatments on RF (Radio Frequency) magnetron sputtered PZI(Pb$\_$1.05/(Zr$\_$0.52/, Ti$\_$0.48/)O$_3$thin films(4000${\AA}$) have been investigated. for a structure of PZT/Pt/Ti/SiO$_2$/Si Crystallization pproperties of PZT films were strongly dependent on RTA(Rapid Thermal Annealing) annealing temperature. We were able to obtain a perovskite structure of PZT at a low temperature of 600$^{\circ}C$. P-E curves of Pd/PZT/Pt capacitor annealed at 700$^{\circ}C$ demonstrate typical hysteresis loops. The measured values of P$\_$r/, E$\_$c/, by post annealed at 700$^{\circ}C$ were 12.1 ${\mu}$C/$\textrm{cm}^2$, 120KV/cm respectively.

• Macromolecular Research
• /
• v.9 no.6
• /
• pp.327-331
• /
• 2001

A new soluble photosensitive poly(amide-co-imide) containing p-phenylenediacryloyl moiety was synthesized and its photoreactivity was characterized. The copolymer was synthesized fromp-phenylenediacryloyl chloride, 4,4-(hexafluoroisopropylidene)diphthalic anhydride and two equivalents of bis(4-aminophenyl) ether in NMP with a subsequent chemical imidization of the resulting poly[amide$\xi$ο-(amic acid)] by acetic anhydride and pyridine. The structure and thermal properties of the polymer were characterized by spectroscopic methods and thermal analyses. The polymer was stable up to 350$\^{C}$, showed good solubility in polar aprotic solvents, and became insoluble after UV irradiation due to the[2+2] cycloaddition of phenylenediacryloyl moiety. Photoreactivity of the polymer was investigated in solution or as a film with respect to the various exposure conditions by UV/Vis spectroscopy. The photosensitivity was noticeably increased with the irradiation temperature, especially in the presense of photosensitizer. The reason for the increased sensitivity was speculated based on the flexibilization of main chain at elevated temperature. Exposure characteristic curves were obtained from the gel fraction experiments after UV irradiation. The sensitivity and contrast at 160$\^{C}$ were measured to be 293 mJ/㎠ and 1.64, respectively.

• The Korean Journal of Food And Nutrition
• /
• v.7 no.4
• /
• pp.392-398
• /
• 1994

The purpose of this study was to predict the actions and roles of 10 strains of representative psychrotrophic lactic acid bacteria, in kimchi fermentation, which were Isolated from kimchi and identified as Leu. mesenteroides subsp. mesenteroides, Leu. mesenteroides subsp. dextranicum, Leu. lactic, Leu. paramesenteroides, Lac. bavaricus and Lac. homahiochii. For this, 0.01% of tactic starters were inoculated in germ free Korean cabbage-juice containing 2.5% NaCl, and then cultivated for 14 days at 1$0^{\circ}C$. All strains grew actively, and reached their stationary phase in 4 days. In death phase, the slopes of curves were much different each other by strains. The acidity increased rapidly between 2 and 4 days, and the pH decreased rapidly between 2 and 3 days. The total acidity was 0.5B~0.75%, the volatile acidity 0.04~0.18% and the pH 3.55~3.85, in final cultures. The cultures of Leuconostocs were better than those of lactobacilli on flavor test. It was thought that the ripening periods of kimchi would be much reduced, and that the over ripening would be also somewhat avoided, when these strains were used as starter bacteria for kimchi and the kimchi was fermented at low temperature.

• Archives of Pharmacal Research
• /
• v.24 no.6
• /
• pp.601-606
• /
• 2001

A simple assay method of recombinant human epidermal growth factor (rhEGF) in a pharmaceutical preparation was studied and validated by capillary electrophoresis (CE) using micellar electrokinetic chromatography (MEKC) techniques. Factors affecting the migration behavior and separation performances of the peptide; type of buffers pH, butler concentration, and concentration of sodium dodecyl sulfates (SDS) were investigated to optimize the analytical performance. CE was performed using running buffers 50.0 mM borate (pH 8.5) containing 12.5 mM SDS at 20 $mutextrm{V}$ of the applied voltage. Calibration curves for the rhEGF showed good linearity (r>0.999) over the wide dynamic range from 1.25 to $100{\mu\textrm{g}}/ml$. Sample analysis was performed by using standard addition method to eliminate the matrix effects of dosage vehicle. This method is assumed to be useful for quality control (QC) of various forms of pharmaceutical products of the peptide.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.89-92
• /
• 2001

A rigid-viscoplastic finite element code for superplastic forming processes has been developed The material is assumed to be isotropic and a modified Coulomb friction law is adopted to explain contact between tool and sheet. This code uses the triangular element based on the membrane approximation and a hierarchical contact searching method is implemented The optimum pressure-time relationships for target strain rate are calculated by several pressure control algorithms. By the analysis, optimum pressure-time curves and deformation behavior are predicted.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.41-48
• /
• 2005

A small scale impact apparatus, pressuremter and soil chamber were used to investigate horizontal behavior and bearing capacity of the steel guardrail post installed in compacted soil. A useful test and data reduction method for pressuremter was developed to evaluate soil parameters of surrounding soil and stability of the post. From the analyses of the PMT, horizontal bearing capacity of the post impacted by a boggie was 12.7% bigger than that of the post with static loading. The increased horizontal bearing capacity is due to generated inertia force that is dependent on the shape of failed soil wedge around the post. P-y curves were obtained from the pressuremeter test and were applied to a finite difference program which predicted a load-deflection and a bending moment contours along the post.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.363-370
• /
• 2001

A computationally efficient algorithm to analyze a group pile behavior is proposed by consideration of both soil-pile and pile-cap interactions. Using toad transfer method the nonlinear characteristics of the soil-pile interaction for a single pile is modeled by piecewise linear soil springs (p-y, t-z, and q-z curves). Beam-column method, one of the most practical approaches, is used for numerical modeling of the soil-pile system. In addition to the group effect resulting from the soil-pile-soil interaction, for a more realistic analysis it is essential to consider the effect of pile-cap interaction including geometric configuration of the piles in a group and conectivity conditions between piles and the cap. This paper mainly focuses on the pile-cap interaction and the development of a rational numerical procedure of its incorporation with the beam-column method.

• Journal of Power System Engineering
• /
• v.8 no.4
• /
• pp.38-43
• /
• 2004

Thermal spraying onto the metal substrate has been widely used as a technique of the surface treatment in the various industrial field. A wide range of thermal spray technologies exist and all rely on the fundamental process of fusing a metal feedstock, atomizing it and transporting it to the surface of a substrate. Specially, these methods have been taken into account as the protection method against the corrosion. In this study, the polarization characteristics were carried out on the thermal sprayed coating layer immersed in various pH of diluted aqueous solutions at $25^{\circ}C$. Aluminum, Zinc, Ni-base alloy, alumina and polyethylene powder were used with sprayed coating materials. From the polarization curves, the electrochemical corrosion potential($E_{corr}$) and the corrosion current density($I_{corr}$) were investigated.