• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.428-432
• /
• 2012

Polyamidimide (PAI)-colloidal silica (CS) nanohybrid films were synthesized by an advanced sol-gel process. The synthesized PAI-CS hybrid films have a uniform and stable chemical bonding and there is no interfacial defects observed by TEM. The thermal degradation ratio of PAI-CS (10 wt%) hybrid films is delayed by 100 ℃ compared with pure PAI sample determined by on set temperature range in TGA. The dielectric constant of PAI-CS (10 wt%) hybrid films decreases with increasing CS content up to about 5 wt% but increases at higher CS content, which is not explained simply by effective medium therories (EMT). The duration time of PAI-CS (10 wt%) hybrid coil is 38 sec, which is very longer than that of pure PAI coil sample. The PAI-CS (10 wt%) hybrid film has a higher breakdown voltage resistance than the pure PAI film at surge environment and exhibits superior heat resistance. The PAI-CS (10 wt%) sample shows the advanced and stable thermal emission properties in transformer module compared with the pure PAI sample. This result illustrates that the advanced thermal conductivity and expansion properties of PAI-CS sample in the case of appropriate sol-gel processes brings the stable thermal emission in transformer system. Therefore, new PAI-CS hybrid samples with such stable thermal emission properties are expected to be used as a high functional coating application in ET, IT and electric power products.

• Analytical Science and Technology
• /
• v.20 no.4
• /
• pp.355-360
• /
• 2007

The title complex, $(C_3H_{12}N_2)[\{Cd(H_2O)(C_6H_5O_7)\}_2]{\cdot}6H_2O$, I, has been prepared and its structure characterized by FT-IR, EDS, elemental analysis, ICP-AES, and X-ray single crystallography. It is triclinic system, $P{\bar{1}}$ space group with a = 10.236(2), b = 11.318(2), c = $13.198(2){\AA}$, ${\alpha}=77.95(1)^{\circ}$, ${\beta}=68.10(1)^{\circ}$, ${\gamma}=78.12(1)^{\circ}$, V = $1373.5(3){\AA}^3$, Z = 2. Complex I has constituted by protonated 1,3-diaminopropane cations, citrate coordinated cadmium(II) anions, and free water molecules. The central cadmium atoms have a capped trigonal prism geometry by seven coordination with six oxygen atoms of three different citrate ligands and one water molecule. Citrate ligands are bridged to three different cadmium atoms. Each cadmium atom is linked by carboxylate and hydroxyl groups of citrate ligand to construct an one-dimensional ladder-type assembly structure. The polymeric crystal structure is stabilized by three-dimensional networks of the intermolecular O-H${\cdots}$O and N-H${\cdots}$O hydrogen-bonding interaction.

• Restorative Dentistry and Endodontics
• /
• v.36 no.6
• /
• pp.477-482
• /
• 2011

Objectives: The purpose of this study was to compare the microshear bond strength (uSBS) to enamel prepared with different burs and to determine what type of bur were chosen when a self-etching primer adhesive was used. Materials and Methods: Enamel of forty-two human molars were used. They were divided into one of six groups (n = 7), Group 1, coarse (125 - 150 ${\mu}m$) diamond bur; Group 2, standard (106 - 125 ${\mu}m$) diamond bur; Group 3, fine (53 - 63 ${\mu}m$) diamond bur; Group 4, extrafine (20 - 30 ${\mu}m$) diamond bur; Group 5, plaincut carbide bur (no. 245); Group 6, cross-cut carbide bur (no. 557). Clearfil SE Bond and Clearfil AP-X (Kuraray Medical Inc.) was bonded to enamel surface. The bonded specimens were subjected to uSBS testing. Results: The uSBS of Group 4 was the highest among groups and it was significantly higher than that of Groups 1, 2, 3, and 6 (p < 0.05), but it was not significantly different from that of Group 5. Conclusions: Different burs used on enamel surface affected the microshear bond strengths of a self-etching primer adhesive to the enamel surface. In the case of Clearfil SE Bond, extrafine diamond and plain-cut carbide bur are recommended for bonding to enamel.

• Korean Journal of Soil Science and Fertilizer
• /
• v.10 no.1
• /
• pp.1-6
• /
• 1977

Fifteen soils including volcanic ash, acid sulfate and degraded saline soils were investigated for Languir adsorption isotherm of ammonium using $NH_4H_2PO_4$. The results are as follows. Languir adsorption maxima of ammonium (LAMA) ranged from 2.4me/100g soil to 12.3 and the average was 5.3. Initial concentration of 30 to 60 or 40 to 80 ppm(as N) appears to be suitable for LAMA measurement. There were two LAMA in some soils. Difference between adsorption constants (bonding energy) was mostly greater than that between LAMA. LAMA ranged from 9.4% to 72% of cation exchange capacity and average was 47%. It did not show any clear tendency with CEC, pH, organic matter content, base saturation percent, P, K, Ca, Mg, Na and Si. Except volcanic ash soils which were grouped into two groups according to ammonium adsorption LAMA was significantly (r=0.951 at 1%) correlated with adsorption at 200ppm. This single concentration seems suitable for LAMA measurement. Probable mechanism of ammonium adsorption was discussed, in which the associated anions were combined with iron and aluminum and then ammonium was bound to phosphorus. Applicability of Langmuir adsorption isotherm model to the soils under field condition was also discussed.

• Applied Chemistry for Engineering
• /
• v.9 no.3
• /
• pp.424-429
• /
• 1998

Cloud-point data at $230^{\circ}C$ and 1,800 bar are presented for two poly(ethylene-co-vinyl alcohol)(PEVA) copolymers[9.9mol% and 17.8mol% vinyl alcohol(VA)] in ethylene, propane, propylene, n-butane, 1-butene, dimethyl ether(DME), and chlorodifluromethane(CDFM). The static type experimental apparatus with a view cell has been used for the experiment at the high pressure and temperature. The pressure-temperature (P-T) loops of PEVA(9.9mol% VA) copolymer-DME mixtures are presented at copolymer concentrations of 1.4wt% to 20.0wt%. Also, we presented the phase behavior of PEVA(17.8mol% VA) copolymer-DME system at copolymer concentration of 1.9wt% to 6.8wt%. The cloud-point curves for the PEVA copolymers in dimethyl ether showed single phase above 480 bar as a result of the hydrogen bonding between the vinyl alcohol unit and dimethyl ether. The pressure-concentration(P-x) isotherm loops of PEVA(9.9mol% and 17.8mol% VA)-DME system are obtained. The cloud-point curves for PEVA(9.9mol% and 17.8 mol% VA) copolymers andthe ethylene, propane, propylene, n-butane, 1-butene, and CDFM all show negative slopes of phase behavior and are located at pressures below 1,800 bar. For PEVA copolymer-DME system(9.9mol% VA), cloud-point curves show positive slopes that decrease in pressures with decrease in temperature in the temperature range of $80^{\circ}C$ to $160^{\circ}C$.

• The Journal of Korean Academy of Prosthodontics
• /
• v.29 no.3
• /
• pp.33-41
• /
• 1991

Cermic has been widely used because of its excellent esthetics and strength. The recently introduced castable ceramic system is regarded as the more esthetic and biocompatible restorative material. The purpose of this study was to compare the shear bond strength of Dicer & G-Cera porcelain laminate veneer according to the type of cement and surface treatment and to observe the surface of bonding failure with SEM. Total forty disks(3.5mm $diam.\times2.0mm$ thickness) were prepared. Forty extracted human maxillary central incisor teeth were stored in saline solution. Ten teeth were bonded to Dicer specimen with Dicer ZPC cement and ten teeth were bonded with Dicer resin cement. Ten silicoated G-Cera specimen and ten non-silicoated G-Cera specimen were bonded to teeth with G-Cera resin cement. Bonded units were mounted in a plastic tube with hard stone and stored in a humidor at $37^{\circ}C$ for 24 hours. Shear bond strength was measured by Instron Universal Testing Machine (Model 1125) and all the specimen were observed with SEM(JEOL, JSM-T2000)and modes of failure were recorded. The obtained results were as follows: 1. The mean shear bond strength of Dicer bonded with Dicer resin cement was 11.62 MPa and that bonded with Dicor ZPC cement was 0.88 MPa : Shear bond strength of Dicer bonded with Dicer resin cement was significantly increased(P<0.05). 2. The mean shear bond strength of silicoated G-Cera was 13.10 MPa and that of non silicoated G-Cera was 10.93 MPa : Shear bond strength of silicoated G-Cera was not significantly increased (P>0.05). 3. Shear bond strength of Dicer and G-Cera porcelain laminate veneer was not significantly different (P>0.05). 4. In observation of bond failure with SEM, Dicer bonded with Dicer ZPC cement exhibited adhesive failure. Dicer bonded with Dicer resin cement and silicoated and non silicoated G-Cera exhibited cohesive failure.

• The Journal of Korean Academy of Prosthodontics
• /
• v.56 no.4
• /
• pp.269-277
• /
• 2018

Purpose: This study examined the effects of glass infiltration treatments on the shear bond strength (SBS) between zirconia core and ultra low-fusing porcelain veneer. Materials and methods: The zirconia specimens were classified into 4 groups (n = 12): Untreated zirconia (group Z), zirconia coated ZirLiner (group ZL), glass-infiltrated zirconia (group ZG), glass-infiltrated and sandblasted zirconia (group ZGS). A cylinder of ultra low-fusing veneer porcelain was build up on each disk ($6mm{\times}3mm$). SBS was measured using a universal testing machine. Scanning electron microscope and Energy Dispersive X-ray spectroscopy were used to evaluate the surface of zirconia and failure pattern after SBS. Results: SBS value of group ZGS was significantly lower than that of other groups (P < .05). No significant differences were detected among group ZL, group Z and group ZG. Conclusion: Glass infiltration is not effective to the bond strength between zirconia and ultra low-fusing porcelain veneer. Sandblasting also dramatically decreased the bonding strength.

• Journal of the Mineralogical Society of Korea
• /
• v.16 no.3
• /
• pp.215-222
• /
• 2003

The Rietveld structure refinement for the natural trioctahedral mica, phlogopite-1M (Parker Mine, Quebec, Canada) has been done by high resolution neutron powder diffraction at $25^{\circ}C$ and -263$^{\circ}C$. The structural formula of phlogopite determined by electron probe microanalysis is $K_2$(M $g_{4.46}$F $e_{0.83}$A $l_{0.34}$ $Ti_{0.22}$)(S $i_{5.51}$A $l_{2.49}$) $O_{20}$(O $H_{3.59}$ $F_{0.41}$). Cell parameters are a=5.30∼5.31 $\AA$, b=9.18∼9.20 $\AA$, c=10.18∼10.21 $\AA$, $\beta$=100.06∼100.08$^{\circ}$. Refinements converged to R values in the range of $R_{p}$=2.35%, $R_{wp}$=3.01%, respectively. In this study, the OH bond length is calculated to 0.93 $\AA$ at room temperature and 1.03 $\AA$ at -263$^{\circ}C$, and the angles between OH vector and (001) plane are obtained 93.4$^{\circ}$∼93.6$^{\circ}$. The decrease in the length of OH with the increase in temperature should be due to the hydrogen bonding in the structure of phogopite.e.e.f phogopite.e.e.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.95-104
• /
• 2018

The structures and energies of the anhydrate and hydrate (hydrate rate: h of 1) states of L-alanine (LA) and glycine (G) were calculated by quantum chemical calculations (QCCs) using B3LYP/6-31G(d,p) for four types of conformers (${\beta}$-extended: ${\Phi}/{\Psi}=t-/t+$, $PP_{II}$: g-/t+, $PP_{II}$-like: g-/g+, and ${\alpha}$-helix: g-/g-). In LA and G, which have an imino proton (NH), three conformation types of ${\beta}$-extended, $PP_{II}$-like, and ${\alpha}$-helix were obtained, and water molecules were inserted mainly between the intra-molecular hydrogen bond of $CO{\cdots}HN$ in $PP_{II}$-like and ${\alpha}$-helix, and attached to the CO group in ${\beta}$-extended. In LA and G, $PP_{II}$-like conformers were most stable in the anhydrate and hydrate states, and the result for LA was different from some experimental and theoretical results from other studies reporting that the main stable conformation of alanine oligopeptide was $PP_{II}$. The formation pattern and stability of the conformation of the oligopeptide was strongly dominated by the presence/absence of intra-molecular hydrogen bonding of $CO{\cdots}HN$, or the presence/absence of an $NH_2$ group in the starting amino acid.

• The Journal of Korean Academy of Prosthodontics
• /
• v.51 no.1
• /
• pp.27-32
• /
• 2013

Purpose: The aims of this study were to evaluate the effect of a resin coating on the shear bond strength of indirect composite restoration bonded to dentin with a self adhesive resin cement and to compare the shear bond strength with that of a conventional resin cement. Materials and methods: The occlusal enamels of thirty six extracted noncarious human molars were removed until the dentin flat surfaces of the teeth were exposed. Then, they were divided into 3 groups. The dentin surfaces of group 1 and 3 were left without any conditioning, while the dentin surfaces of group 2 were resin-coated with Clearfil SE bond and a flowable resin composite, Metafil Flo. After all specimens were temporized for 24 hours, indirect composite resin blocks fabricated by Tescera were bonded to dentins by Unicem for group 1 and 2, and by Panavia F for group 3. After 48 hours of water storage, shear bond strengths were measured. The data was analyzed with one-way analysis of variance and multiple comparison test (Tukey method). Results: The shear bond strengths of Unicem applied to resin coated dentin surfaces were significantly higher than those of Unicem and Panavia F used to uncoated dentin surfaces (P<.0001). Conclusion: Application of a resin coating to the dentin surface significantly improved the shear bonding strength of a self adhesive resin cement in indirect restoration.