• 한국신뢰성학회지:신뢰성응용연구
• /
• 제15권3호
• /
• pp.197-206
• /
• 2015

Failure analysis of pre-insulated pipe (SPPS 380, 400A) transporting high temperature water ($95{\sim}110^{\circ}C$) for a plant was carried out. The damaged area (${\Phi}5mm$) of pre-insulated pipe was found only on welds. The chemical composition of damaged pipe meets specification of carbon steel pipes for pressure service (KS D 3562). As results of microstructure analysis, crack propagated from outer to inside after pitting corrosion occurred on the outside surface. The non-metallic inclusion existed on the end of crack. And the non-metallic inclusion continuously and linearly formed along with the bond line of welds. Based on SEM-EDS analysis, the nonmetallic inclusions have higher Manganese (Mn) and Oxygen (O) content but sulfur (S) was not detected. As results of water quality analysis, hydrogen ion concentration and minerals like Fe, Mg, Si were in low level. But the content of dissolved oxygen (11.2 ppm) was slightly higher than that of standard. It seems that the cause of damaged pipe is grooving corrosion due to MnO inclusion formed on bond line and corrosion took place nearby welds.

• 한국세라믹학회지
• /
• 제35권2호
• /
• pp.201-207
• /
• 1998

A tube-type filter dam(or baffle with holes) for ferrous melt refining is applied to the tundish operation for molten steel having low carbon and ultra-low carbon. The changes in the total oxygen content insoluble aluminum content and the distribution of inclusion size in molten steel during tundish operation were in-vestigated at the pouring part strand and mold of tundish. Removal mechanism of inclusions is considered to be caused by buoyancy action of the filter dam better than filtration action and the size range of in-clusions filtrated by the filter dam was for 30-50$\mu\textrm{m}$. Decrease in deviation of inclusion content in molten steel was confirmed for appling the filter dam in comparison with using conventional dam and weir. Also the filter dam had the advantage of baffle with holes at lower part in the efficiency of inclusions removal.

• 소성∙가공
• /
• 제19권5호
• /
• pp.311-319
• /
• 2010

Rare earth metal Ce has a relatively low melting point and high specific gravity. Because of its significantly high affinity to oxygen, nitrogen and sulfur, it is highly usable as a steel refining agent. However, because Ce compound has relatively high specific gravity, it is difficult to be separated from molten steel through floatation, and it degrades the purity of molten steel, or may clog the nozzle in continuous casting. Such problem may be solved by using an appropriate deoxidation agent together with Ce and settling molten steel sufficiently after refining. Thus a fundamental study in the formation behavior of non-metallic inclusion in Ce added Hyper Duplex STS melts was investigated. The addition amount of Ce, melt temperature were considered as experimental variables. A main non-metallic inclusion in mother alloy is 51(wt%MnO) - 27.6(wt%SiO$_2$)- 10.9(wt%$Cr_2O_3$). Non-metallic inclusion was dramatically decreased and the particle size was fined as the amount of Ce increased. Moreover (%MnO) and (%SiO$_2$) of non-metallic inclusion were decreased. But (%$Al_2O_3$)were relatively increased. The number of non-metallic inclusion were decreased and the large particle size were increased by increasing the temperature of molten steel.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.197-201
• /
• 2009

A lot of work is carried out concerning to acicular ferrite formation in the weld metal of high strength and low-alloy steel. Those results are suggesting that oxides that contain titanium elements provides nucleation site of intragranular ferrite, referred as acicular ferrite. Thus, when intragranular ferrite is expected to form in heat-affected zone, oxide containing titanium element should be formed in the steel. However, normal steel is deoxidized by using aluminum element (Al-killed steel) with little oxygen content. It means almost oxygen is deoxidized with aluminum elements. In the present work, in order to form the acicular ferrite in the heat affected zone, with the same concept in the case of weld metal, the steel deoxidized with titanium element (titanium killed-steel) is prepared and the acicular ferrite formation is observed in detail by using laser-conforcal microscopy technique. The confocal technique makes it possible that the morphological change along the phase transformation from austenite to ferrite is in-situ tracked. Thus, the inclusion that stimulated the ferrite nucleation could be directly selected from the observed images, in the HAZ of the Ti-killed steel. The chemical composition of the selected inclusion is analyzed and the nucleation potential is discussed by changing the nucleation site with boron element. The potency for the ferrite nucleation is summarized and the existence of effective and ineffective manganese sulfide for nucleation is made clear.

• Journal of Welding and Joining
• /
• 제11권4호
• /
• pp.79-90
• /
• 1993

Shielded metal arc welding, one-ploe and two-pole submerged arc welding were accomplished to investigate microstructure changes on phase transformation behavior in $60kg/mm^2$ quenched and tempered high strength steel. Microstructures were examined by optical micrograph and TEM. In shielded metal arc welding (oxygen 250ppm), the inclusions were small size (0.3-0.5$\mu\textrm{m}$)and small in number. In submerged arc welding (oxygen 430-529ppm), the inclusions were larger(0.7-2$\mu\textrm{m}$) than that of shielded metal arc welding and large in number. Microstructure mainly depends on number and distribution of inclusions in fusion zone of weld metal. It was noticed that a limited number of inclusions favors the formation of acicular ferrite.

• Journal of Welding and Joining
• /
• 제5권3호
• /
• pp.38-45
• /
• 1987

An investigation was conducted to find out the factors influencing on the impact toughness of austenitic-and duplex stainless steel weld metal. Various welding process with commerically available consumables was adopted to get weld doposited metal. The oxygen content of each weld metal was very sensitiive to welding process, involving flux composition, shielding gas and structural features. The results of this study show tat the content of oxygen as an oxide inclusion significantly affects impact toughness, and .delta.-ferrite distribution is also correlated with resultant toughness value.

• 농약과학회지
• /
• 제18권4호
• /
• pp.358-363
• /
• 2014

신규 병원성세균 Bacillus thuringiensis CAB565, 566균주를 이용한 산업배지에서의 배양조건에 따른 독소단백질의 차이를 확인하였다. 포도당, 효모추출물 등으로 구성된 산업배지의 산소 전달 속도를 확인하고자 소형배양기에서 임펠러와 배지 농도에 따른 산소전달계수(KLa)의 차이를 확인하였다. 교반기의 통기량이 많을수록 그리고 배지 농도가 높아질수록 산소전달계수(KLa) 값이 상승하였다. 하지만 교반속도는 200 rpm에서 가장 효율적이었고, 교반속도가 상승할수록 효과가 떨어졌다. Microsparger를 이용하여 배양 중 단계적으로 통기속도를 높여 배지내 용존산소농도를 50% 이상으로 유지시켜 배양한 결과 생균수는 배양 후 16시간, 포자수는 54시간에 최대의 농도값을 보였다. 그 결과, B.t. CAB565의 생균수는 $2.3{\times}10^{10}cell/ml$, 포자수는 $1.9{\times}10^{10}spore/ml$ 그리고 B.t. CAB566의 생균수는 $1.8{\times}10^{10}cell/ml$, 포자수는 $1.4{\times}10^{10}spore/ml$를 보였다. 탄소원의 농도는 포도당의 농도가 5%일 때, 세포성장에 가장 유리한 것으로 조사되었다.

• Bulletin of the Korean Chemical Society
• /
• 제20권8호
• /
• pp.943-947
• /
• 1999

Ligand field analyses for tris(biuret)chromium(III) chloride and hexaureachromium(III) bromide were performed and compared to understand the ligand field properties of both ligands. The optimized eσO and eπO values indicate that coordinated oxygen atom in biuret ligand is a moderate s- and strong p-donor, while that in urea ligand is a weak σ- and moderate π-donor. The electronic structures of those two complexes are quite different and they were well accounted by inclusion of an anisotropic p bonding.

• 암석학회지
• /
• 제2권1호
• /
• pp.19-31
• /
• 1993

Oxygen isotope compositions of whole rock and/or mineral separates (quartz and feldspar) have been determined for the granitic and related rocks from the Wolf River Batholith, Wisconsin. Hydrothermal alteration resulting in the decrease of ${\Delta}_{Q-F}$/ values was obaserved locally throughout the batholith. Feldspars of different colors (pink, gray and red) were separated whenever feasible and analyzed. Most red feldspars (An$_{10-30}$/) show the highest and constant ${\delta}^18O$/ values (9.3~10.0 permil) suggesting nearly complete isotope exchange with hydrothermal fluid. Based on ${\delta}^18O$/ values and the alteration temperatures (260~$350^{\circ}C$) estimated from fluid inclusion study, ${\delta}^18O$/ of fluid is calculated to be $5.0{\pm}1.4$ permil. Phanerozoic sedimentary formation water in Wisconsin is most likely the source of the fluid.

• 자원환경지질
• /
• 제32권3호
• /
• pp.237-245
• /
• 1999

The Mujeong au-Ag hydrothermal vein type deposits occur within the Teriary igneous rocks of the Janggi basin. Ore minerals consist of pyrite, pyrrhotite, sphalertite, chalcopyrite, galena, cosalite, lillianite, argentite and electrum, and associated with epidotization, sericitization and pyritization. Fluid inclusion studies reveal that ore fluids were low saline with a simple NaCl-$H_{2}O$ system. Fluid inclusion data indicate that homogenization temperatures and salinities of fluid are 150 to $340^{\circ}C$ and 1.0 to 6.5wt.% NaCl equivalent, respectively. Sulfur isotope compositions of sulfied minerals ( ${\delta}^{34}S$=6.2 to 9.6$\textperthousand$) indicate that the ${\delta}^{34}S_{H2S}$ value of ore fluids was about 10.4$\textperthousand$. This ${\delta}^{34}S_{H2S}$ value is likely consistent with and hydrothermal sulfur, whereas the fluids were highly influenced by mixing with meteoric water. Measured and calculated oxygen and hydrogen isotope values (${\delta}^{18}O_{H2O}$=-2.7 to 3.4 $\textperthousand$, ${\delta}D_{H2O}$ = -83.6 to -52.7 $\textperthousand$) of ore forming fluids suggest mixing with hydrothermal and meteoric water. Equilibrium thermodynamic interpretation by mineral assemblages and chemistry indicates that sulfur fugacities (-log $fs_2$) ore forming fluids range from 9.0 to 12.6 atm stage II.