• 한국자기학회지
• /
• 제18권1호
• /
• pp.24-27
• /
• 2008

Polyol법을 이용하여 $MnFe_2O_4$ 나노입자를 제조하고, X-선 회절기(XRD)와 진동시료형 자화율 측정기(VSM)를 이용하여 결정학적 및 거시적인 자기적 특성을 분석하였고, 뫼스바우어($M\"{o}ssbauer$) 분광실험을 통하여 $MnFe_2O_4$ 물질의 초미세 상호작용에 대한 연구를 수행하였다. 고분해능 투과형 전자 현미경(High Resolution Transmission Electron Microscope; HRTEM)을 이용하여 입자의 크기를 분석한 결과, 대부분의 입자크기가 $6{\sim}8$ nm 정도의 분포를 가지는 매우 균일한 입자로 형성되었음을 확인할 수 있었다. X-선 회절실험의 분석 결과, $a_0=8.418{\pm}0.001{\AA}$의 격자상수를 가지는 입방정형의 스피넬 구조로써 그 공간군이 Fd3m 임을 확인하였다. 상온에서의 VSM 측정결과 강한 초상자성 거동을 보였고, 뫼스바우어 분석결과로 상온에서 초상자성 영향에 따른 요동현상이 나타남을 관측할 수 있었다. 4.2K에서는 6개의 공명흡수선이 2 set으로 존재하고 초미세 자기장 값($H_{hf}$)이 A-site의 경우 498 kOe, B-site의 경우 521 kOe 로 분석되었다.

• 전기전자학회논문지
• /
• 제13권1호
• /
• pp.57-64
• /
• 2009

The optoelectrical characteristics of the ZnO nanoparticles (NPs) annealed in vacuum or oxygen condition from $200^{\circ}C$ to $600^{\circ}C$ were examined. Increased on-off ratio (or, the ratio of photocurrent to dark current) was observed when they were annealed at $300^{\circ}C$, $400^{\circ}C$ and $500^{\circ}C$ with the values enhanced about 4 orders compared to the as-prepared ZnO NPs in both annealing conditions, while the maximum efficiency was shown at the annealing temperature of $600^{\circ}C$ for the ZnO NPs annealed in vacuum with the value of 29.8 mA/W and at the temperature of $500^{\circ}C$ for those annealed in oxygen condition with the value of 40.3 mA/W. Photoresponse behavior of the ZnO NPs annealed in oxygen showed the sharp increase right after the ir exposure to the light followed by the slow decay and saturation during steady illumination, differing from the ZnO NPs annealed in vacuum which only exhibited the gradual increase. This difference occurred due to the curing effect of the oxygen vacancies. SEM images indicated no change in their morphologies with annealing, indicating the change in their internal structures by annealing, and most remarkably at $600^{\circ}C$. As for their photoluminescence(PL) spectra, the decrease of the deep-level(DL) emission was observed when they were annealed in oxygen at $400^{\circ}C$, and not at $200^{\circ}C$ and $600^{\circ}C$.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.64.2-64.2
• /
• 2010

In order to improve the overall power conversion efficiency in dye-sensitized solar cells (DSSCs), it is very important to secure the sufficient surface area of photocatalytic nanoparticles layer for absorbing dye molecules. It is because increasing the amount of dye absorbed generally results in increasing the amount of light harvesting. In this work, we proposed a new method for increasing the specific surface area of photocatalytic titanium oxide ($TiO_2$) nanoparticles by using an inorganic templating method. Salt-$TiO_2$ composite nanoparticles were synthesized in this approach by spray pyrolyzing both the titanium butoxide and sodium chloride solution. After aqueous removal of salt from salt-$TiO_2$ composite nanoparticles, mesoporous $TiO_2$ nanoparticles with pore size of 2~50 nm were formed and then the specific surface area of resulting porous $TiO_2$ nanoparticle was measured by Brunauer-Emmett-Teller (BET) method. Generally, commercially available P-25 with the average primary size of ~25 nm $TiO_2$ nanoparticles was used as an active layer for dye-sensitized solarcells, and the specific surface area of P-25 was found to be ~50 $m^2/g$. On the other hand, the specific surface area of mesoporous $TiO_2$ nanoparticles prepared in this approach was found to be ~286 $m^2/g$, which is 5 times higher than that of P-25. The increased specific surface area of $TiO_2$ nanoparticles will absorb relatively more dye molecules, which can increase the short curcuit current (Jsc) in DSSCs. The influence of nanoporous structures of $TiO_2$ on the performance of DSSCs will be discussed in terms of the amount of dye molecules absorbed, the fill factor, the short circuit current, and the power conversion efficiency.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.141-145
• /
• 2007

Due to their excellent catalytic activity with respect to methanol oxidation on platinum at low temperature, platinum nanosized catalysts have been a topic of great interest for use in direct methanol fuel cells (DMFCs). Since pure platinum is readily poisoned by CO, a by-product of methanol electrooxidation, and is extremely expensive, a number of efforts to design and characterize Pt-based alloy nanosized catalysts or Pt nanophase-support composites have been attempted in order to reduce or relieve the CO poisoning effect. In this review paper, we summarize these efforts based upon our recent research results. The Pt-based nanocatalysts were designed by chemical synthesis and thin-film technology, and were characterized by a variety of analyses. According to bifunctional mechanism, it was concluded that good alloy formation with $2^{nd}$ metal (e.g., Ru) as well as the metallic state and optimum portion of Ru element in the anode catalyst contribute to an enhanced catalytic activity for methanol electrooxidation. In addition, we found that the modified electronic properties of platinum in Pt alloy electrodes as well as the surface and bulk structure of Pt alloys with a proper composition could be attributed to a higher catalytic activity for methanol electooxdation. Proton conducting contribution of nanosized electrocatalysts should also be considered to be excellent in methanol electrooxidation (Spillover effect). Finally, we confirmed the ensemble effect, which combined all above effects, in Pt-based nanocatalsyts especially, such as PtRuRhNi and $PtRuWO_{3}$, contribute to an enhanced catalytic activity.

• 한국분말재료학회지
• /
• 제21권5호
• /
• pp.377-381
• /
• 2014

This work describes the coloration, chemical stability of $SiO_2$ and $SnO_2$-coated blue $CoAl_2O_4$ pigment. The $CoAl_2O_4$, raw materials, were synthesized by a co-precipitation method and coated with silica ($SiO_2$) and tin oxide ($SnO_2$) using sol-gel method, respectively. To study phase and coloration of $CoAl_2O_4$, we prepared nano sized $CoAl_2O_4$ pigments which were coated $SiO_2$ and $SnO_2$ using tetraethylorthosilicate, $Na_2SiO_3$ and $Na_2SiO_3$ as a coating material. To determine the stability of the coated samples and their colloidal solutions under acidic and basic conditions, colloidal nanoparticle solutions with various pH values were prepared and monitored over time. Blue $CoAl_2O_4$ solutions were tuned yellow color under all acidic/basic conditions. On the other hand, the chemical stability of $SiO_2$ and $SnO_2$-coated $CoAl_2O_4$ solution were improved when all samples pH values, respectively. Phase stability under acidic/basic condition of the core-shell type $CoAl_2O_4$ powders were characterized by transmission electron microscope, X-ray diffraction, CIE $L^*a^*b^*$ color parameter measurements.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.1.1-1.1
• /
• 2011

Printed electronics based on the direct writing of solution processable functional materials have been of paramount interest and importance. In this talk, the synthesis of printable inorganic functional materials (conductors and semiconductors) for thin-film transistors (TFTs) and photovoltaic devices, device fabrication based on a printing technique, and specific characteristics of devices are presented. For printable conductor materials, Ag ink is designed to achieve the long-term dispersion stability and good adhesion property on a glass substrate, and Cu ink is sophisticatedly formulated to endow the oxidation stability in air and even aqueous solvent system. The both inks were successfully printed onto either polymer or glass substrate, exhibiting the superior conductivity comparable to that of bulk one. In addition, the organic thin-film transistor based on the printed metal source/drain electrode exhibits the electrical performance comparable to that of a transistor based on a vacuum deposited Au electrode. For printable amorphous oxide semiconductors (AOSs), I introduce the noble ways to resolve the critical problems, a high processing temperature above $400^{\circ}C$ and low mobility of AOSs annealed at a low temperature below $400^{\circ}C$. The dependency of TFT performances on the chemical structure of AOSs is compared and contrasted to clarify which factor should be considered to realize the low temperature annealed, high performance AOSs. For photovoltaic application, CI(G)S nanoparticle ink for solution processable high performance solar cells is presented. By overcoming the critical drawbacks of conventional solution processed CI(G)S absorber layers, the device quality dense CI(G)S layer is obtained, affording 7.3% efficiency CI(G)S photovoltaic device.

• Asian Pacific Journal of Cancer Prevention
• /
• 제15권24호
• /
• pp.10705-10711
• /
• 2015

Oral cancer is one of the most common and lethal cancers in the world. Combination chemotherapy coupled with nanoparticle drug delivery holds substantial promise in cancer therapy. This study aimed to evaluate the efficacy and safety of two dosages of our novel pH and temperature sensitive doxorubicin-methotrexate-loaded nanoparticles (DOX-MTX NPs) with attention to the MMP-2 mRNA profile in a 4-nitroquinoline-1-oxide induced oral squamous cell carcinoma (OSCC) model in the rat. Our results showed that both IV and oral dosages of DOX-MTX NP caused significant decrease in mRNA levels of MMP-2 compared to the untreated group (p<0.003). Surprisingly, MMP-2 mRNA was not affected in DOX treated compared to cancer group (p>0.05). Our results indicated that IV dosage of MTX-DOX is more effective than free DOX (12 fold) in inhibiting the activity of MMP-2 in OSCCs (P<0.001). Furthermore, MMP-2 mRNA expression in the DOX-MTX treated group showed a significant relation with histopathological changes (P=0.011). Compared to the untreated cancer group, we observed no pathological changes and neither a significant alteration in MMP-2 amount in either of healthy controls that were treated with oral and IV dosages of DOX-MTX NPs whilst cancer group showed a high level of MMP-2 expression compared to healthy controls (p<0.001).Taking together our results indicate that DOX-MTX NPs is a safe chemotherapeutic nanodrug that its oral and IV forms possess potent anti-cancer properties on aggressive tumors like OSCC, possibly by affecting the expression of genes that drive tumor invasion and metastasis.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.165-165
• /
• 2014

In this study, we demonstrated that the soft lithographic patterning processing of chemical vapor deposition (CVD) graphene and rGO sheets as large scale, low cost, high quality and simplicity for future industrial applications. Recently, a previous study has reported that single layer graphene grown via CVD was patterned and transferred to a target surface by controlling the surface energy of the polydimethylsiloxane (PDMS) stamp [1]. Using this approach, the surface of a relief-patterned elastomeric stamp was functionalized with hydrophilic dimethylsulfoxide (DMSO) molecules to enhance the surface energy of the stamp and to remove the graphene-based layer from the initial substrate and transfer it to a target surface [2]. Further, we developed a soft lithographic patterning process via surface energy modification for advanced graphene-based flexible devices such as transistors or simple and efficient chemical sensor consisting of reduced graphene oxide (rGO) and a metallic nanoparticle composite. A flexible graphene-based device on a biocompatible silk fibroin substrate, which is attachable to an arbitrary target surface, was also successfully fabricated.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.458.2-458.2
• /
• 2014

We have demonstrated that simple brush-painted Ti-doped $In_2O_3$(TIO) films can be used as a cost effective transparent anodes for organic solar cells (OSCs). We examined the RTA effects on the electrical, optical, and structural properties of the brush painted TIO electrodes. By the direct brushing of TIO nanoparticle ink and rapid thermal annealing (RTA), we can simply obtain TIO electrodes with a low sheet resistance of 28.25 Ohm/square and a high optical transmittance of 85.48% under atmospheric ambient conditions. Furthermore, improvements in the connectivity of the TIO nano-particles in the top region during the RTA process play an important role in reducing the resistivity of the brush-painted TIO anode. In particular, the brush painted TIO films showed a much higher mobility ($33.4cm^2/V-s$) than that of previously reported solution-process transparent oxide films ($1{\sim}5cm^2/V-s$) due to the effects of the Ti dopant with higher Lewis acid strength (3.06) and the reduced contact resistance of TIO nanoparticles. The OSCs fabricated on the brush-painted TIO films exhibited cell-performance with an open circuit voltage (Voc) of 0.61 V, shot circuit current (Jsc) of $7.90mA/cm^2$, fill factor (FF) of 61%, and power conversion efficiency (PCE) of 2.94%. This indicates that brush-painted TIO film is a promising cost-effective transparent electrode for printing-based OSCs with its simple process and high performance.

• Rapid Communication in Photoscience
• /
• 제3권1호
• /
• pp.16-19
• /
• 2014

Anodic self-organized titania nanotube (TNT) arrays have a great potential as efficient electron-transport materials for dye-sensitized solar cells (DSSC). Herewith we report the photovoltaic and kinetic investigations for a series of heteroleptic ruthenium complexes (RD16-RD18) sensitized on TNT films for DSSC applications. We found that the RD16 device had an enhanced short-circuit current density ($J_{SC}/mAcm^{-2}=15.0$) and an efficiency of power conversion (${\eta}=7.2%$) greater than that of a N719 device (${\eta}=7.1%$) due to the increasing light-harvesting and the broadened spectral features with thiophene-based ligands. However, the device made of RD17 (adding one more hexyl chain) showed smaller $J_{SC}(14.1mAcm^{-2})$ and poorer ${\eta}(6.8%)$ compare to those of RD16 due to smaller amount of dye-loading and less efficient electron injection for the RD17 device than for the RD16 device. For the RD18 dye (adding one more thiophene unit and one more hexyl chain), we found that the device showed even lower $J_{SC}(13.2mAcm^{-2}) $ that led to a poorest device performance (${\eta}=6.2%$) for the RD18 device. These results are against to those obtained from the same dyes sensitized on $TiO_2$ nanoparticle films and they can be rationalized according to the electron transport kinetics measured using the methods of charge extraction and transient photovoltage decays.