• 한국세라믹학회지
• /
• 제55권5호
• /
• pp.498-503
• /
• 2018

Using the thermal ablation method, the oxidation behavior of $SiC_f/SiC$ composites was investigated in air and in the temperature range of $1,300^{\circ}C$ to $2,000^{\circ}C$. At the relatively low temperature of $1,300^{\circ}C$, passive oxidation, which formed amorphous phase, predominantly occurred in the thermal ablation test. When the oxidation temperature increased, SiO (g) and CO (g) were formed by active oxidation and the dense oxide layer changed to a porous one by vaporization of gas phases. In the higher temperature oxidation test, both active oxidation due to $SiO_2$ decomposition on the surface of the oxide layer and active/passive oxidation transition due to interfacial reaction between oxide and base materials such as SiC fiber and matrix phase simultaneously occurred. This was another cause of high temperature degradation of $SiC_f/SiC$ composites.

• Corrosion Science and Technology
• /
• 제19권3호
• /
• pp.138-145
• /
• 2020

Immersion tests of Alloy 600 were conducted in simulated primary water environments of a pressurized water reactor at 325 ℃ for 10, 100, and 1000 h to obtain insight into effects of surface deformation on internal and intergranular (IG) oxidation behavior through precise characterization using various microscopic equipment. Oxidized samples after immersion tests were covered with polyhedral and filamentous oxides. It was found that oxides were abundant in mechanically ground (MG) samples the most. The number density of surface oxides increased with time irrespective of the method of surface finish. IG oxidation occurred in mechanically polished (MP) and chemically polished (CP) samples with thin internal oxidation layers. However, IG oxidation was suppressed with relatively thick internal oxidation layers in MG samples compared to MP and CP samples, suggesting that MG treatment could increase resistance to primary water stress corrosion cracking (PWSCC) from the standpoint of IG oxidation. As a result, appropriate surface treatment for Alloy 600 could prevent oxygen diffusion into grain boundaries, inhibit IG oxidation, and finally induce its high PWSCC resistance.

• 한국세라믹학회지
• /
• 제33권7호
• /
• pp.816-822
• /
• 1996

서로 다른 흑연화도를 갖는 furan 수지로 부터 얻어진 무기화합물(SiC, TiO2) 첨가 탄소재료의 산화반응의 흑연구조 의존성에 대하여 살펴보았다. 탄소재료의 산화는 시료의 표면적에 크게 의존하여, 흑연화가 상당히 진행된시료라 할지라도 표면적이 클 때는 살화속도도 빠른 것으로 밝혀졌으며, 단위 중량이 아닌 단위면적당의 산화속도로 바꿔 생각했을 때 흑연화가 진행될 수록 산화반응도 늦어지는 것을 알 수 있었다. 그리고 겉보기 활성화 에너지값으로 부터 생각할 때 흑연(TiO2 첨가시료)과 난층흑연(SiC 첨가시료)이 동일한 반응기구에 의해 산화가 진행되는 것으로 판단되었다. 또한 두종류 이상의 결정구조가 혼재하여 있는 시료의 경우 이들 성분들의 산화속도는 달라 반응의 초기에 흑연으로 결정화된 않은 비정질 탄소 성분이 흑연 성분보다 먼저 선택적으로 산화되는 것을 알 수 있었다.

• 한국주조공학회지
• /
• 제25권6호
• /
• pp.226-232
• /
• 2005

Contact material is widely used in the field of electrical parts. Ag-CdO material has a good wear resistance and stable contact resistance. In order to establish optimizing heat treatment condition, rolling temperature and oxidation process, we studied the microstructure of Ag-CdO material with various conditions. The experimental procedure were melting using high frequency induction, heat treatment, rolling and internal oxidation. And we experimented on difference process, Post-oxidaion. In this study, we obtained the optimizing heat treatment condition was $700^{\circ}C$ for 15 min. and the optimizing rolling temperature was $730^{\circ}C$. In investigation of the microstructure of oxidized material, coarse oxide and depleted oxidation layer existed. The hardness was average Hv 70. When we used Post-oxidation, oxides were finer than prior process and depleted oxidation layer did not exist. The hardness of Post-oxidation material was average Hv 80. And the optimizing rolling temperature was $800^{\circ}C$.

• Preventive Nutrition and Food Science
• /
• 제17권2호
• /
• pp.158-165
• /
• 2012

This study was designed to investigate whether the fatty acid composition could make a significant contribution to the oxidation stability of vegetable oils marketed in Korea. Ten kinds, 97 items of vegetable oils that were produced in either an industrialized or a traditional way were collected and analyzed for their fatty acid compositions and lipid oxidation products, in the absence or presence of oxidative stress. Peroxidability index (PI) calculations based on the fatty acid composition ranged from 7.10 to 111.87 with the lowest value found in olive oils and the highest in perilla oils. In the absence of induced oxidative stress, malondialdehyde (MDA), the secondary lipid oxidation product, was generated more in the oils with higher PI (r=0.890), while the tendency was not observed when the oils were subjected to an oxidation-accelerating system. In the presence of the oxidative stress, the perilla oils produced in an industrialized manner generated appreciably higher amounts of MDA than those produced in a traditional way, although both types of oils presented similar PIs. The results implicate that the fatty acid compositions could be a predictor for the oxidation stability of the vegetable oils at the early stage of oil oxidation, but not for those at a later stage of oxidation.

• 한국표면공학회지
• /
• 제49권4호
• /
• pp.389-394
• /
• 2016

The operation method of nuclear power plants is currently changing to high burn-up and long period that can enhance economics and efficiency of the plant. Since nuclear plant operation environment has been becoming severe, the amount of absorbed hydrogen also has increased. Absorbed hydrogen can be fatal securing safety of nuclear fuel cladding in case of Loss of Coolant Accidents(LOCA). In order to examine the impact of hydride on high-temperature oxidation, high-temperature oxidation experiment was performed on normal Zry-4 cladding and on Zry-4 cladding where hydrogen is charged in air pressure steam atmosphere under the $950^{\circ}C$ and $1000^{\circ}C$. According to the results, while oxidation acceleration due to charged hydrogen was not observed prior to breakaway oxidation creation, oxidation began to accelerate in cladding where hydrogens charged as soon as the breakaway oxidation started. If so much hydrogen are charged in the cladding, equiaxial monoclinic phase to unstable of stress is formed and it is presumed that oxidation is accelerated because nearby stress caused a crack in equiaxial phase, and that makes corrosion resistance decline sharply.

• Corrosion Science and Technology
• /
• 제21권1호
• /
• pp.53-61
• /
• 2022

Alloys of Fe-(5.3-29.8)%Mn-(1.1-1.9)%Al-(0.4-0.5)%C were oxidized at 550 ℃ to 650 ℃ for 20 h to understand effects of alloying elements on oxidation. Their oxidation resistance increased with increasing Mn level to a small extent. Their oxidation kinetics changed from parabolic to linear when Mn content was decreased and temperature was increasing. Oxide scales primarily consisted of Fe₂O₃, Mn₂O₃, and MnFe₂O₄ without any protective Al-bearing oxides. During oxidation, Fe, Mn, and a lesser amount of Al diffused outward, while oxygen diffused inward to form internal oxides. Both oxide scales and internal oxides consisted of Fe, Mn, and a small amount of Al. The oxidation of Mn and carbon transformed γ-matrix to α-matrix in the subscale. The oxidation led to the formation of relatively thick oxide scales due to inherently inferior oxidation resistance of alloys and the formation of voids and cracks due to evaporation of manganese, decarburization, and outward diffusion of cations across oxides.

• KSBB Journal
• /
• 제23권3호
• /
• pp.245-250
• /
• 2008

퀴놀린은 생물학적으로 거의 산화 분해되지 않았으나, 250$^{\circ}C$ 습식산화에서 니코틴산과 초산 등으로 산화 분해되었다. 퀴놀린 습식산화는 균일촉매 $CuSO_4$ 또는 쉽게 습식산화 분해되는 페놀에 의해 반응조건이 완화되었다. 퀴놀린 습식산화 반응의 주 생성물 중 하나인 니코틴산은 호기성 Bacillus 종균에 의해 산화 분해되었다. 촉매를 사용하지 않은 고온에서의 퀴놀린 습식산화 생성물의 생물학적 산화는 저온에서 진행된 균일 촉매 ($CuSO_4$) 습식산화와 퀴놀린-페놀 혼합용액 습식산화 반응 생성물의 생물학적 산화에 비하여 늦게 진행되었다. 반면에, 호기성 균주의 습식산화 생성물에의 적응은 생물학적 처리에서의 니코틴산 산화 분해 반응의 지체기를 크게 단축시켰다.

• 한국재료학회지
• /
• 제3권4호
• /
• pp.403-409
• /
• 1993

본 논문에서는 Si(111)에 대한 건식산화와 어닐링에서 결함의 억제 또는 제거에 $NH_3$가 효과적임을 밝혔다. 산화방식은 건식산화(dry $O_2$ oxidation)및 $NH_3$산화($NH_3$ added in dry $O_2$oxidation)를 택하였고 $N_2$및 $NH_3N_2$분위기에서 어닐링 효과를 평가하였다. 건식산화에서는 발생되는 결함이 성장시간에 따라서 길이가 길어지며, $NH_3$산화에서는 결함이 발견되지 않았다. 또한 초기산화를 $NH_3$산화로 하고서 건식산화를 하였을 때 계면에서의 결함을 제거하는 효과가 있다. 건식산화 또는 $NH_3$산화를 한 후 이들 시료에 대하여 7.5% $NH_3N_2$분위로 어닐링하면OSF의 게터링(gettering)효과가 있었다. $NH_3$산화방식에서 7.5%$NH_3N_3$분위기로 어닐링했을때가 건식산화방식에 비하여 OSF의 길이가 20%정도 감소하였다. OSF의 모양은 pit형으로 (111)면에 대하여 (011)면 쪽으로 게터링이 일어났으며<110>방향으로 식각되는 성질이 있었다.

• 한국자기학회지
• /
• 제12권4호
• /
• pp.127-131
• /
• 2002

자성터널접합(magnetic tunnel junction: MTJ)소자의 AlO$_{x}$터널장벽 절연층을 플라즈마 산화법으로 2번에 나누어 금속증착.산화를 반복하여 만들어 보았다. 이중산화I그룹은 10A의 $\AA$의 Al 하부 절연막을 증착하고 산화시간을 10 s로 완성한 후 그 위에 13$\AA$의 Al을성막하고 50, 80, 120s간 산화시켜 완성한 절연막의 특성을 알아보았다. 이중산화II그룹은 10$\AA$봐 Al하부 절연막의 산화시간을 30~120 s간 달리하고 그 위에 13 $\AA$의 Al을 성막하고 210 s간 산화시켜 완성한 절연막의 특성을 알아보았다. 이중산화공정으로 제조된 시편은 전 실험범위에서 자기저항비(magnetoresistance： MR)는 27% 이상으로 우수하였고, 이는 13 $\AA$의 Al을 증착하고 한번만 산화시키는 통상의 단일산화에 비해 MR비가 우수하고 공정범위가 넓었다. 수직단면 투과전자현미경(transmission electron microscope： TEM)으로 미세구조를 확인한 결과 이중산화가 단일산화보다도 더 얇고 균일한 두께를 유지함을 알 수 있었다 X선광전자분석(X-ray photoelectron spectroscopy： XPS)으로 확인한 결과 이중산화는 절연막층 하부 CoFe 자성층의 Fe의 산화를 방지하여, 결과적으로 단일산화법에 비해서 하부자성층의 산화를 방지하여 긴 산화시간 공정 범위에서도 우수한 MR비를 가질 수 있었다.