• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.12 no.4
• /
• pp.195-202
• /
• 2000

Recently, wave dissipating structures with porosity are widely used to improve habor tranquility and to reduce the wave overtopping rate. In this study, hydraulic model tests were performed to examine hydraulic efficiency of slit caissons, igloo blocks, and hollow blocks. The model tests showed that slit caissons were the most effective in dissipating wave energy under moderate wave conditions. Slit caissons and igloo blocks showed no significant difference in reducing wave overtopping rate. Hallow blocks are less effective in reducing wave overtopping rate than slit caissons and igloo blocks lU1der higher wave energy conditions.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.3
• /
• pp.18-24
• /
• 2005

Wave overtopping is one of the most important processes for the design of seawalls. The term "wave overtopping" is used here to refer to the processes where waves hit a sloping structure run up the slope and, if the crest level of the slope is lower than the highest run up level, overtop the structure. Wave overtopping is dependent on the processes associated with breaking wave. A numerical model based on Navier-Stokes equation and the Marker-density function for predicting wave overtopping of coastal structures is developed in this paper. In order to evaluate the present model, two simulations are tested. One is overflow without waves at vertical seawall, and the other is wave overtopping at sloping seawalls.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.05a
• /
• pp.121-127
• /
• 2003

Wave overtopping is one of the most important hydraulic responses of breakwater because it significantly affects its functional efficiency, the safety of transit and mooring on the rear side, wave transmission in the sheltered area, rear side armor stones and to some extent, the structural safety itself. In this study, hydraulic model tests has been carried out to investigate the influence of berm's size on overtopping rate by maximum overtopping rate and mean overtopping rate. The hydrodynamic characteristics of berm breakwater by the overtopping rate can be summarized as follows: 1. It is better to use maximum overtopping rate than to use mean overtopping rate for design of coastal structures in the point of view of stability. 2. When construct berm to decrease energy of waves that it was needed to make breaking conditions of wave on the berm. 3. Under the relative length of berm was over 0.13 overtopping rate was significantly decreased. 4. Overtopping rate affected significantly by the relative length of yhe berm than height of the berm.

• Ocean Systems Engineering
• /
• v.10 no.4
• /
• pp.359-371
• /
• 2020

The performance of a multi-level overtopping wave energy converter (OWEC) has been numerically and experimentally investigated in a two-dimensional wave tank in order to study the effects of opening width of additional reservoirs. The device is a fixed OWEC consisting of an inclined ramp together with several reservoirs at different levels. A particle-based numerical simulation utilizing the Lattice Boltzmann Method (LBM) is used to simulate the flow behavior around the OWEC. Additionally, an experimental model is also built and tested in a small wave flume in order to validate the numerical results. A comparison in energy captured performance between single-level and multi-level devices has been proposed using the hydraulic efficiency. The enhancement of power capture performance is accomplished by increasing an overtopping flow rate captured by the extra reservoirs. However, a noticeably large opening of the extra reservoirs can result in a reduction in the power efficiency. The overtopping flow behavior into the reservoirs is also presented and discussed. Moreover, the results of hydrodynamic performance are compared with a similar study, of which a similar tendency is achieved. Nevertheless, the LBM simulations consume less computational time in both pre-processing and calculating phases.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.15 no.3
• /
• pp.163-169
• /
• 2012

In this paper, model test on the Tapdong's revetment at Jeju-si has been conducted to figure out the causes of frequent occurrence of wave overtopping and to suggest the action plan. In the model test, the reflection coefficients were measured according to the change of wave periods for with and without armor stones. Also, the wave overtopping rate and the wave pressures inside revetment structure for 4 types of upper block were estimated for various wave heights and wave periods, which are chosen based on the NE design wave with 50 year return period. It is found that the increase of the upper structure's height and the modification of the curved protruding shape are effective in reducing the overtopping rate.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.14 no.1
• /
• pp.11-18
• /
• 2011

Wave overtopping reef system with guide vanes convert incident wave energy on the reef type structures into electric power. Previous studies decided shape parameters likes slope, height of the sloping arm and shape of guide vane. In this paper, using these shape parameters produce 1/7 scale model and construct integration scale model system combining water pressure head turbine, power generation, power control, operating control and monitoring system. In these systems, we measure the overtopping and power generation with different wave heights and periods and compare the results with the previous studies. This was confirmed designed overtopping and power generation, then we suggest efficient control system.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.4
• /
• pp.323-330
• /
• 2010

An efficient wave energy converter with new overtopping flow device on which spiral reefs are attached is proposed by Maritime and Ocean Engineering Research Institute in Korea and its candidate substructures such as monopile, tripod and jacket are designed. This study investigates modal characteristics of the substructures by analyzing natural frequencies and mode shapes. Based on the modal analysis results, relative strength, governing modes and some complementary design strategies of each candidate substructure are compared and discussed considering water depth conditions.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.7
• /
• pp.992-1001
• /
• 2023

OWEC (Overtopping Wave Energy Converter) is a wave power generation system using the wave overtopping. The performance and safety of the OWEC are affected by wave characteristics, such as wave height, period. To mitigate this issue, optimal OWEC designs based on wave characteristics must be investigated. In this study, the environmental conditions along the Ulleungdo coast were used. The hydraulic efficiency of the OWEC was calculated using SPH (Smoothed Particle Hydrodynamics) by comparing 4 models that changed the substructure. As a result, it was possible to change the substructure. Through design optimization, a new truss-type structure, which is a substructure capable of carrying the design load, was proposed. Through a case study using member diameter and thickness as design variables, structural safety was secured under allowable stress conditions. Considering wave load, the natural frequency of the proposed structure was compared with the wave period of the relevant sea area. Harmonic response analysis was performed using wave with a 1-year return period as the load. The proposed substructure had a reduced response magnitude at the same exciting force, and achieved weight reduction of more than 32%.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.1
• /
• pp.168-174
• /
• 2022

In a wave power generation system, the overtopping system is known as an overtopping wave energy converter (OWEC). The performance of an OWEC is affected by wave characteristics such as height and period because its power generation system is sensitive to those characteristics; these, as well as wave direction, depend on the sea. As these characteristics vary, it is hard for the OWEC to produce power in a stable manner. Therefore, it is necessary to find an appropriate shape for an OWEC, according to the characteristics of the sea it is in. This research verified the effect of the design of the OWEC ramp on the hydraulic efficiency using the smoothed particle hydrodynamics (SPH) particle method. A total of 10 models were designed and used in simulations performed by selecting the design parameters of the ramp and changing the attack angle based on those parameters. The hydraulic efficiency was calculated based on the rate of discharged water obtained from the analysis result. The effect of each variable on the overtopping performance according to the shape of the ramp was then confirmed. In this study, we present suggestions for determining the direction for an appropriately shaped OWEC ramp, based on a specific sea area.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.1
• /
• pp.62-69
• /
• 2015

Coastlines are protected by breakwater structures against the erosion of sand or other materials along beaches due to wave action. This research examined the use of physical modeling to determine the effects of the tetrapod size and vertical walls of a rubble mound on the volume of wave overtopping under irregular wave conditions in coastal areas in Busan Yacht Harbor. In this analysis model, the structures were studied using irregular waves and the JONSWAP wave energy spectrum. To understand the effects of the tetrapod size and heights of the vertical wall, the study considered vertical walls of 0, 1.78, 6.83, and 9.33 cm with armor double layered material tetrapods of 8, 12, 16, and 20 tons. An extensive number of experiments covering a relatively large range of variables enabled a comprehensive discussion. First, in the presence of a short vertical wall, the water level played a key role in the overtopping discharge. In such circumstances, the values of the wave overtopping discharge decreased with increasing freeboard size. In the presence of a tall freeboard and middle, the value of the wave overtopping discharge was equally influenced by the vertical wall factor. Moreover, the tetrapod size decreased by an increase in the vertical wall factor, and relationship between them resulted in a short wall height. From an engineering point of view, considering a small water level may allow the choice of a shorter vertical wall, which would ultimately provide a more economical design.