• Journal of Welding and Joining
• /
• 제27권3호
• /
• pp.80-84
• /
• 2009

The Plasma Transferred Arc (PTA) overlay welding method is lately introduced as one of the most useful surface overlay method of the engine component. In this paper, the overlay welding on the SNCrW heat resisting alloy was conducted by the PTA overlay welding process using the super alloy powder. The characteristics of the overlay layers were investigated through the metallurgical and abrasive test. Experimental results showed that the overlay on the SNCrW heat resisting alloy surface was successfully made without hot cracking. The friction wear characteristics of the Co-base Stellite 6 overlayer were most superior. However the abrasive wear characteristics were most inferior in the Co-base Stellite 6 overlayer.

• Journal of Welding and Joining
• /
• 제32권2호
• /
• pp.4-8
• /
• 2014

In this research, GTA overlay welding system is developed for inside of straight pipes in various diameter. It can be applied to oil, ship building and plant industry, especially pipes connected to pressure vessels, for the purpose of cost reduction by cladding inside of pipes with corrosion and heat resistant alloys such as stainless steel or Inconel. Developed system consists of GTA power source, torch, wire feeding system, automatic arc length adjusting device, CCD camera and cooling unit. Two types of pipe inside overlay welding system are developed. One is for maximum 3m pipe length with 3 inch ~ 12 inch pipe outer diameter. Another type can be applied to maximum 12m pipe length with 7 ~ 24 inch OD. Developed system successfully produced inside cladded pipe and the results are shown through cross sectional images of the pipes.

• 한국기계가공학회지
• /
• 제19권4호
• /
• pp.52-57
• /
• 2020

The frequency of the manufacturing and modification of automotive press dies via overlay welding has recently increased, but the welding quality depends on the operator skills and the working conditions. Therefore, this study presents a way to improve the overlay welding quality regardless of the operator skills. Three welding conditions with different pre- and post-heating treatments were tested on some specimens; the weld surface quality was analyzed by examining the cutting face. The results demonstrated the best quality of the weld surface that was heated before and after the welding.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.505-506
• /
• 2011

• 한국생산제조학회지
• /
• 제22권1호
• /
• pp.138-144
• /
• 2013

The automation technology for overlay welding is needed due to the occurrence of severe corrosion and abrasion on the surface of internal contact in different shape of fittings. In Korea, different shapes of fittings have been manufactured by using the imported equipment of overlay welding automation at some companies. Thus the research on the development of overlay welding automation system (in short, OWAS) for a large L-type tube is urgently needed. In this paper, the investigation is focused on the optimal design of a supporting base for the (currently developing) OWAS of large L-type tube. Specifically we assume that the base which supports the equipment during the process of overlay welding is loaded as self-weight in the direction of gravity through static analysis especially when it is rotated 180 degree on the OWAS. For optimal design of a supporting base for OWAS of large L-type tube, Solidworks(R) (for 3-dimensional modelling) and ANASYS Workbench(R) (for structural analysis) are incorporated so as to proceed an optimization routines based on Response Surface Method (RSM) and Design of Experiment (DOE). In more specific, DOE finds out major factors (or dimensions) of the supporting base by using MINITAB(R). Then the regression equations between design variables (the major factors of supporting base) and response variables (deformation, stress and safety factor for the supporting base), which will be resulted in by RSM, verify the major factors of DOE. In the next step, Central Composite Design (CCD) plans 20 simulations of ANASYS Workbench(R) and then figures out the optimal values of design variables which will be reflected on the manufacturing of supporting base. Finally welding experiment is conducted to figure out the influence of overlay welding quality in applying the optimized design values of supporting base to the actual OWAS.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2001년도 춘계학술발표대회 개요집
• /
• pp.62-64
• /
• 2001

• Journal of Welding and Joining
• /
• 제20권3호
• /
• pp.54-59
• /
• 2002

Overlays is a treatment of the surface and near-surface regions of a material to allow the surface to perform functions that are distinct from those frictions demanded far the bulk of the material. Welding, thermal spray, quenching, carburizing and nitration have been used as the surface treatment. Especially, weld overlay is a relatively thick layer of filler metal applied to a carbon or low-alloy steel base metal for the purpose of providing a wear resistant surface. In this study, weld overlay was performed by MAG welding on the base metal(SS400) with filler metal which contain composite powders($Cr_3C_2+Mn+Mo+NbC$) and solid wire(JIS-YGW11). Characteristics of hardness and wear resistance on overlays were analyzed by EDS, EPMA, XRD and microstructures. Carbide formations were $M(Cr, Fe)_7C_3$ and NbC phases. And carbide volume fraction, hardness and specific wear resistance of overlays were increased with increasing powder feed rate and decreasing wire fred rate. Hardness and wear resistance were almost proportioned to carbide volume fraction of overlay.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1999년도 특별강연 및 추계학술발표대회 개요집
• /
• pp.202-204
• /
• 1999

• 한국산학기술학회논문지
• /
• 제17권12호
• /
• pp.446-452
• /
• 2016

최근 해양, 석유화학 플랜트 등에서는 내마모, 내식성, 내열성이 요구되는 초내열 합금이 기본적인 구조재료로 많이 사용되고 있다. 하지만 고가의 초내열 합금 소재로 밸브를 제작할 때 원가 상승과 가격 경쟁력 저하의 원인이 되고 있다. 이에 유체에 흐르는 특정부위만 육성 용접하는 기술이 효과적인 방법으로 사용되고 있다. 하지만 기존의 볼 육성용접의 경우 사람이 직접 수동으로 작업을 진행하기 때문에 많은 시간이 소요되고 정확한 용접하기 어렵다. 이러한 문제를 해결하기 위해 볼 밸브용 볼 육성용접을 균일하게 할 수 있는 로봇자동화 시스템을 개발하였다. 이 시스템은 용접토치를 장착한 용접용 로봇 6축, 포지셔너 회전을 위한 부가 2축, 제어장치 및 로봇경로는 오프라인 프로그램으로 구성되어 있다. CAD 도면 데이터를 오프라인 프로그램에 입력하여 로봇 교시점과 로봇 구동 소스를 얻을 수 있도록 하였고, 볼 육성용접 궤적은 Matlab을 통해 구현하였다. OLP 시스템을 통해 용접층 두께가 균일하게 얻으므로 용가재의 소모량을 약 20% 절약할 수 있었고, 모재와 용접봉 사이의 아크길이를 일정하게 유지하여 육성용접 불량율을 약 50% 정도 감소시켜 품질을 확보하였다. OLP를 활용한 육성용접 자동화 시스템을 통해 작업소요시간이 88시간에서 41시간으로 단축되어 생산성이 2.58배 향상 되었다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1999년도 특별강연 및 춘계학술발표대회 개요집
• /
• pp.24-27
• /
• 1999