Many type of fuel cell stacks have been developed to improve the efficiency of reactants usage. The cascade type fuel cell stack using dead end operation is able to attain above 99% usage of hydrogen and oxygen. It is sectionalized to several parts and the residual reactants which are used previous parts would be supplied again to next parts which have less number of cells in dead end operation stack. The oversupply of reactants which is usually 120%~150% of the theoretical amount to generate current for preventing the flooding effect could be provided to each part except the last one. The final section which is called monitoring cells is supposed to be supplied insufficient the fuel or oxidant that would have some accumulated inert gas from former parts. It makes some voltage drop in the part and the fresh reactants must be supplied to the part for recovering it by venting the residual gas. So the usage of fuel and oxidant is depend on the time and frequency of opening valves for venting of residual gas and it is important to optimize the vent logic for achieving higher usage of hydrogen and oxygen. In this research, many experiments are performed to find optimal condition by evaluating the effect of time and frequency under several power conditions using over 100kW class fuel cell module. And the characteristics of the monitoring cells are studied to know the proper cell voltage which decide the condition of opening the vent valve for stable performance of the cascade type fuel cell module.
Finite element model updating is very effective procedure to determine the uncertainty parameters in structural model and minimize the differences between experimentally and numerically identified dynamic characteristics. This procedure can be practiced with manual and automatic model updating procedures. The manual model updating involves manual changes of geometry and analyses parameters by trial and error, guided by engineering judgement. Besides, the automated updating is performed by constructing a series of loops based on optimization procedures. This paper addresses the ambient vibration based finite element model updating of long span reinforced concrete highway bridges using manual model updating procedure. Birecik Highway Bridge located on the $81^{st}km$ of Şanliurfa-Gaziantep state highway over Firat River in Turkey is selected as a case study. The structural carrier system of the bridge consists of two main parts: Arch and Beam Compartments. In this part of the paper, the arch compartment is investigated. Three dimensional finite element model of the arch compartment of the bridge is constructed using SAP2000 software to determine the dynamic characteristics, numerically. Operational Modal Analysis method is used to extract dynamic characteristics using Enhanced Frequency Domain Decomposition method. Numerically and experimentally identified dynamic characteristics are compared with each other and finite element model of the arch compartment of the bridge is updated manually by changing some uncertain parameters such as section properties, damages, boundary conditions and material properties to reduce the difference between the results. It is demonstrated that the ambient vibration measurements are enough to identify the most significant modes of long span highway bridges. Maximum differences between the natural frequencies are reduced averagely from %49.1 to %0.6 by model updating. Also, a good harmony is found between mode shapes after finite element model updating.
For this research with the objects of spaces in two department stores which can be referred to as representative facility of commercial space, observation test has carried out to estimate how much visitors rivet their eyes to the display of shops. In addition, to find out what effect the difference among the department types has on the selective attention to space element, the observation time was applied as a medium for estimation. The followings are the result from analyzing the observation frequency and the observation intensity feature of each section where the characteristics of design could be found at attention. First, both images of A and B had concentrative dominant-observation at left shops. In case of Image A, Customers began to observe the right shops very attentively after 25 seconds, and with Image B, the attentive observation at right and left took place alternatively after 35 seconds. In other words, regardless of the characteristics of shop displays, the left shops were observed first while in case of the observation after the early and middle time-frame the characteristics of shops were found to have effects on observation. Second, the normal observation showed some difference among attention sections over time while on the whole both images of A and B had the same highly attentive observation at the middle space. Accordingly, it could be concluded that the middle space was playing a faithful role as background for commercial spaces. Third, the ignorant observation, which is the opposite to the attentive observation, was found different between the images of A and B. When the ignorant observation is considered to have intentionality, it will be possible to set up the display which may attract the attention aggressively by the process of figuring out the characteristics of ignored shops.
Joint strength between a solder ball and a pad on a substrate is one of the major factors which have effects on electronic device reliability. The effort to improve solder joint strength via surface cleaning, heat treatment and solder composition change have been in progress. This paper will discuss the method of solder ball joint strength improvement using LF hydrogen radical cleaning treatment and focus on the effects of surface treatment condition on the solder ball shear strength and interfacial reactions. In the joint without radical cleaning, voids were observed at the interface. However, the specimens cleaned by hydrogen-radical didn't have voids at the interface regardless of cleaning time. The shear strength between the solder ball and the pad was increased over 120%(about 800gf) when compared to that without the radical treatment (680gf) under the same reflow condition. Especially, at the specimen treated for 5minutes, ball shear strength was considerably increased over 150%(1150gf). Through the observation of fracture surface and cross-section microstructure, the increase of joint strength resulted from the change of fracture mode, that is, from the solder ball fracture to IMC/Ni(P) interfacial fracture. The other cases like radical treated specimen for 1, 3, 7, 9min. showed IMC/solder interfacial fracture rather than fracture in the solder ball.
The purpose of this study was to analyze domestic research trends over the past 20 years and future direction of forest ecology using text mining. A total of 1,015 academic papers and keywords data related to forest ecology were collected by the "Research and Information Service Section" and analyzed using big data analysis programs, such as Textom and UCINET. From the results of word frequency and N-gram analyses, we found domestic studies on forest ecology rapidly increased since 2011. The most common research topic was "species diversity" over the past 20 years and "climate change" became a major topic since 2011. Based on CONCOR analysis, study subjects were grouped intoeight categories, such as "species diversity," "environmental policy," "climate change," "management," "plant taxonomy," "habitat suitability index," "vascular plants," and "recreation and welfare." Consequently, species diversity and climate change will remain important topics in the future and diversifying and expanding domestic research topics following global research trendsis necessary.
Statistical analyses of cut-slope stability were performed over approximately 5.7 km section along the National road No. 25, which cross-cuts in NW-SE direction the Cheongwon and Boeun-Gun area, Chungbuk. A measure of slope-stability was established by using direct reinforcement and indirect protection methods in whole section. Orientations(dip/dip direction) of the slopes, foliations(bedding), cleavages and joints were measured in total of 30 slope sites. The results analyzed using stereographic projection indicate that major directions of the slopes come out predominantly in three directions: 1) $58^{\circ}/095^{\circ}$, 2) $60^{\circ}/296^{\circ}$ and 3) $59^{\circ}/212^{\circ}$. In analyses of dip direction and frequency of cut-slopes established by reinforcement and protection methods, slopes with dip direction of $80-120^{\circ}$ and $280-320^{\circ}$ mostly occur. However, slopes with dip direction of $0-80^{\circ}$(N and NW) and $120-160^{\circ}$(SE) are not distributed in the study area. Failure aspects were analyzed for three major directions of the slopes, respectively. The results of failure aspects analyzed indicate that slopes in the study area could generate various failures as the results of intersection and/or intersection combination among joints, foliations(bedding) and cleavages. However, possibility of failure in a slope of major direction No. 3 is statistically very low because of low frequency in total number of slopes with the direction and of formation of small scale-slopes geographically, although the slope might generate all aspects of failure-modes.
Purpose: To analyze the clinical and angiographic features with outcome of transcatheter arterial embolization in patients with secondary postpartum hemorrhage. Materials and Methods: Clinical details and angiographic features with assessment of arterial embolization were reviewed in total 38 patients underwent arterial embolization at single tertiary referral center. Results: Twenty patients (53%) had Cesarean section. The major causes of bleeding were iatrogenic vascular injury, and retained placenta (55%). The patterns of vaginal bleeding were recorded as intermittent (50%), or as persistent (50%). Seven patients (18%) were hemodynamically unstable at presentation. Positive angiographic findings appeared in eighteen patients (47.3%). The frequency of pseudoaneurysm was statistically high in the Cesarean section (p < 0.001). The used embolic agents except gelfoam were N-butyl cyanoacrylate (n = 7), and microcoil (n = 7). Unilateral selective embolization (26.3%) was shown effective in superselective embolization of bleeding focus. Technical and clinical success rate were 100% and 97.4%, respectively with no complication. Sixteen resumed regular menstruation, and one pregnancy were observed in patients with available follow-up of over 6 months. Conclusion: Considerable rate of hemodynamically unstable patients was observed with high rate of positive angiography findings. Given high successful rate and few complications, early angiographic assessment with embolization should be considered.
A median is a safety feature most commonly used to separate opposing traffic on a divided highway. In designing highways, the selection and installation of a median can be a critical part from a safety viewpoint because road crossing accidents are definitely more serious than other accidents. In regard to the important function of the median. the proper countermeasure ought to have been provided and thorough study should have been carried out. In this paper, traffic accident data are analyzed to examine the accident reduction effect of the median, which are gathered from all over 4-lane national roads in Korea. The traffic accident data were categorized into two groups by the existence of a median. For more effective analysis, the data have been classified by accident type, severity. and occurrence time. To compare the effectiveness of median installation, not only the accident frequency but also the accident severity, EPDO. and the occupancy rate of specific accidents have been used as a mode of effectiveness. The analysis of the effectiveness of medians shows that both the accident frequency and the accident severity could decrease by providing a median. Also the section where a median was supplied showed the improvement of overall safety through fewer serious and fatal crashes as well as fewer head-on crashes. Therefore, conclusions can be drawn from results of this study that the median installation is an important means to increase the safety of over 4-lane national roads. This study is expected to provide the reasonability of the median installation by identifying the reduction of traffic accident after the median installation and to play a major role in selecting sections where the median is to be offered.
The prenatal care is the preventive medical service to help the pregnant mother deliver the healthy baby. It's regular examines give some chances to check-up the healthy conditions. This thesis concentrates on the CRM system to support an effective prenatal care system and prove the effectiveness of it. As CRM is the adapted management related to the customer's own information, it is important to develop the CRM model classified by the patients characteristics. A general hospital in Busan operated the CRM system to carry out the effective prenatal care and there is an analysis to ensure the effectiveness of CRM system for the pregnant women in our maternity ward. The results can be summarized as follows: 1) According to the comparisons with the CRM system, we can conclude the system is desirable. (1) Maternal Age : In the age distribution, the prenatal visit frequency, triple marker freqency, oral GTT and targeted ultrasonography in the experimental group in 30 to 34 years old is higher on the whole. For over 35 years old group, the higher frequency comes out in the oral GTT and targeted ultrasonography and for 25 to 29 years old group the different figure shows just in the targeted ultrasonography. (2) Area of residence: There is a clear difference in all the items in Busan and near area but no sign of difference in prenatal visits and oral GTT in other residencial area. Especially in the targeted ultrasonography the higher figure shows in the experimental group located in the both areas. The targeted ultrasonography is known as the specific examination which should be examined by the specialists, on the contrary the other examinations can be operated in the small clinic. So the public information and seminars related with ultrasonography increases the check-up frequency. The clinic requests some ultrasonographical examinations to the specialists in general hospital. (3) Parity: The clear difference shows that the CRM system causes the prenatal visit frequency to become higher in experimental group. The figure is 9.7 times and 8.6 times each. This is opposite that the past study said multiparity reduced the average prenatal visits. But the result of CRM is considered as the method to help the multiparity understand the importance of the prenatal care. (4) Obstetrical history: In the experimental group of the spontaneous delivery group, the figure is higher in the prenatal visit frequency, triple marker, oral GTT and targeted ultrasonography but the Caesarean section delivery group has higher figure in targeted ultrasonography. (5) In the first check-up, the rate of targeted ultrasonography in under 16 week pregnancy, in the 16 week pregnancy to 32 week pregnancy and the over 32 week pregnancy in the experimental group is upper than the compared one. For the oral GTT, there is a difference in under 16 week pregnancy but no difference in prenatal visits and triple marker. 2) The analysis of characteristics of prenatal care through the decision tree resulted in the fact that the most important variable is the residential area. After the delivery frequency is following, the obstetrical history and maternal age are in order. It is the same result in the triple marker and oral GTT. Consequently it is the same order of important variables in CRM system. The effectiveness of CRM system is proved in this study. The CRM system is a marketing method to control and lead the customers through the segmentation of customer data. It increases the new customer aquisition, maintenance of loyal customers, augmentation of customers value, activation of potential customers and creation of life time customers. So eventually it can enlarge the customers value. The medical institution should make efforts to establish the data base enforced by the customer's information on the underlying ordinary data system to carry out the CRM system effectively. In addition, it should develop the a variety of marketing strategy in order to set up one to one marketing satisfying the needs of individual patients.
The purpose of this study was to analyze domestic research trends related to the Baekdudaegan Mountains in the last two decades. In total, 551 academic papers and keyword data related to the Baekdudaegan Mountains were collected using the "Research and Information Service Section" and analyzed using "big data" analysis programs, such as Textom and UCINET. Papers related to the Baekdudaegan Mountains were published in 177 academic journals, and 229 papers (41.6% of all published papers) were published between 2011 and 2015. According to word frequency data (N-gram analyses), the major research topic over the past 20 years was "species diversity." According to CONCOR analysis results, the main research could be divided into 15 areas, the most important of which was "species diversity," followed by "vegetation restoration and management," and "culture." Ecological research comprised 12 groups with a frequency of 78.8%; humanities and social research comprised 2 groups with a frequency of 15.6%. Overall, our study of research areas and quantitative data analyses provides valuable information that could help establish policy formulation.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.