• 수산해양기술연구
• /
• 제44권3호
• /
• pp.239-249
• /
• 2008

Trawlers have to a sufficient towing force due to it's characteristics of the high performance. The newly constructed trawler with the conventional propellers shows the sufficient towing force, so that the propeller and engine are optimized. In the 1970s, many trawlers were imported from overseas by Korean fisheries industries. But the engine output degradation with year by year caused the trawlers to decrease the towing speed of the vessels. On the previous studies, the nozzle propeller had not so good efficiency with increasing of resistance in high-speed cruising operation over 15knots. But the trawling operation is just required the higher thrust and towing force, so that the nozzle propeller is very profitable for the it's effectiveness. A new nozzle propeller was designed for the 4,462G/T trawler, Dong-San, operated by Dongwon Industries Co., Ltd. to improve the towing speed, and the model tests were performed. The model ship and model propeller are preciously manufactured and used model tests in basin. The resistance test and propeller open water test were performed for the cases of the half and full loads. The required engine horse power and RPM were evaluated analytically by the speed-power curve, when the trawler was equipped with the nozzle propeller. The results of tests showed that the towing speed 4.85knots on the design load waterline requires the 200 engine RPM and 2,567ps in the delivered horsepower.

• 한국강구조학회 논문집
• /
• 제24권4호
• /
• pp.423-433
• /
• 2012

본 논문은 전단머리를 갖는 CFT기둥-RC 무량판 접합부에 대한 실물대 실험연구를 요약한 것이다. CFT구조는 여러 가지 구조 및 시공 상의 장점으로 인하여 국내 건설현장에서 상대적으로 짧은 시간에 폭넓게 수용되고 있다. 한편 RC 무량판 구조는 층고절감 및 공기 단축 측면의 장점으로 국내의 지하주차장이나 주거용 건물에 필수적 구조시스템으로 널리 사용되고 있다. 이 두 구조시스템을 조합함으로써 공사기간의 획기적 단축 등 여러 시공 및 구조상의 이점을 극대화할 수 있을 것으로 예상된다. 그러나 CFT기둥-RC 무량판 접합부의 효율적인 디테일은 국내 외적으로 아직 충분히 연구된 바가 없어서 이 분야의 연구가 매우 필요한 실정이다. CFT기둥-RC 무량판 접합부의 구조성능에 영향을 미칠 수 있는 여러 가지 변수를 고려하여 접합상세를 제안하고 실험을 통하여 검증하였다. 실험결과 본 연구에서 제시된 CFT기둥-RC 무량판 접합상세의 펀칭강도는 ACI에서 규정한 RC 무량판 펀칭강도와 동등하거나 상회하는 것을 확인할 수 있었다. 실험결과를 토대로 CFT기둥-RC 무량판의 펀칭전단강도 예측식을 제안하였다.

• 한국직업건강간호학회지
• /
• 제27권1호
• /
• pp.36-47
• /
• 2018

Purpose: This study aimed to examine the effects of interpersonal relationship ability, job stress, and stress coping type on the turnover intention of nurses in the early stage of their careers. Methods: Data were collected from 136 early stage nurses from two general hospitals and one tertiary hospital in Chungbuk province. An early stage nurse was defined as the nurse with a work experience of 3 to 36 months. The collected data were analyzed using independent t-test, one-way ANOVA, Mann-Whitney U test, Person's correlation coefficient, and stepwise multiple regression. Results: It was seen that turnover intention had a negative correlation with interpersonal competency (r=-.20, p=.020) and a positive correlation with job stress (r=.56, p<.001). Job stress due to work over load, inadequate compensation and working environment, interpersonal relationship ability, and length of clinical career were significant factors influencing turnover intention (p<.05). These variables explained for 50.4% of the variance in turnover intention. Conclusion: It is necessary to develop an interpersonal relationship ability improvement program to decrease turnover intention among early stage nurses by helping them to successfully adapt to their job. Moreover, it is important to bring about continuous improvements in terms of provision of adequate workload and appropriate rewards, and creation of a suitable work environment to reduce the job stress of early stage nurses.

• 한국강구조학회 논문집
• /
• 제18권6호
• /
• pp.769-782
• /
• 2006

상시 운행 열차는 운행 속도 대역폭이 한정되어 있기 때문에 속도에 따른 교량의 동적응답 특성 파악에는 한계가 있다. 따라서 본 연구에서는 교량상을 통과하는 열차 속도와 교량의 동적응답의 상관관계를 파악하기 위하여 실운행 디젤 기관차 1량에 의한 증속실험을 실시하였다. 가속도 응답특성 분석을 위하여 지점부를 제외한 전구간에 걸쳐 등간격으로 7개의 수직가속도와 중앙부에 1개의 수평가속도계를 부착하였다. 교량의 중앙부에는 연직방향과 횡방향 거동특성 파악을 위하여 수직 변위계, 수평 변위계, 휨변형률계를 각각 1개씩 설치하였다. 실험 차량을 대상 교량의 중앙부와 지점부에 정적재하 후 5km/h부터 90km/h까지 10km/h씩 증속하였고, 각 속도 대역별로 2회씩 반복하여 실험을 실시하였다. 실측 데이터의 필터링 방법에 따른 진동 평가 방법의 적절성을 검토하였고, 연직방향 진동가속도 대비 횡방향 진동수준을 평가하였으며, 속도에 따른 처짐, 변형률 및 윤중변동 특성을 검토하였다.

• Tribology and Lubricants
• /
• 제31권4호
• /
• pp.183-188
• /
• 2015

This paper presents the experimental effects of lubricant with nanodiamond particles in sliding friction. In order to improve the performance of lubricants many additives are used, such as MoS₂, cadmium chloride, indium, sulfides, and phosphides. These additives are harmful to human health and to the environment, so alternatives are necessary. One such alternative is nanodiamond powder, which has a large surface area. In order to investigate the effect of nanodiamonds in lubricants under sliding friction, they are dispersed in the lubricant at a variety of concentrations (0 wt%, 0.1 wt%, 0.3 wt%, 0.5 wt%, and 1 wt%) using the matrix synthesis method. Friction and wear tests are performed according to the ASTM G99 method using a pin-on-disc tester at room temperature. The specimens used in this experiment are AISI 52100 ball bearings and AISI 1020 steel discs. During the test, lubricant mixed with nanodiamond is supplied constantly to keep the two bodies separated by a lubricant film. To maintain boundary lubrication, the speed is set to 0.18 m/s and a load of 294 N is applied to the disc through the pin. Results are recorded by using workbench software over the test duration of 10 minutes. Experimental results show that when the concentration of nanodiamond increases, the coefficient of friction decreases. However, above a nanodiamond concentration of 0.5 wt%, both the coefficient of friction and wear volume increase. From this experiment, the optimum concentration of nanodiamond showing a minimum coefficient of friction of 0.09 and minimum wear volume of 0.82 nm² was 0.5 wt%.

• 대한조선학회논문집
• /
• 제52권1호
• /
• pp.8-18
• /
• 2015

Reduction of the fuel oil consumption and corresponding greenhouse gas exhausted from ships is an important issue for today's ship design and shipping. Several concepts and devices on the superstructure of a container ship were suggested and tested in the wind tunnel to estimate the air drag reduction. As a preliminary performance evaluation, air drag contributions of each part of the superstructure and containers were estimated based on RANS simulation respectively. Air drag reduction efficiency of shape modification and add-on devices on the superstructure and containers was also estimated. Gap-protectors between containers and a visor in front of upper deck were found to be most effective for drag reduction. Wind tunnel tests had been carried out to confirm the drag reduction performance between the baseline(without any modification) configuration and two modified superstructure configurations which were designed and chosen based on the computation results. The test results with the modified configurations show considerable aerodynamic drag reduction, especially the gap-protectors between containers show the largest reduction for the wide range of heading angles. RANS computations for three configurations were performed and compared with the wind tunnel tests. Computation result shows the similar drag reduction trend with experiment for small heading angles. However, the computation result becomes less accurate as heading angle is increasing where the massively separated flow is spread over the leeward side.

• Journal of Biosystems Engineering
• /
• 제27권1호
• /
• pp.11-18
• /
• 2002

One of the major obstructing factors against managing dairy farm in Korea has been a shortage of roughage supply, which resulted in excessive abuse of concentrate feed. In order to solve this problem, production of the wrap silage by the winter cereal forages raised in the fallow paddy field is strongly recommended in Korea. The main objective is to develop a tractor attached round bale wrapper which can process the silage by wrapping the round bales with thin plastic films. This is the first half of the study which is divided by two parts. In this first part, bale wrapping process was analyzed, and based on this results the followings were designed, developed and tested. 1. Bale wrapper which haying the maximum capacity of 1 ton bale with various functions such as loading, wrapping, discharging the round bales and supplying and cutting wrap films was designed. 2. An actuator and its hydraulic circuit of each process were developed and tested. 3. Also, the variations of hydraulic pressure and engine speed were investigated by operating bale wrapper developed. In this test, maximum pressure of the hydraulic circuit for the bale wrapping was 130 kg/㎠ when it raised the bale, which was quite below the relief pressure of 170 kg/㎠ of hydraulic circuit. In the engine speed test, speed drop was 20∼67 rpm, which meant that there was no over-load operation. Therefore, the experiment proved that developed hydraulic circuit and mechanism is stable in bale wrapping operation

• 센서학회지
• /
• 제28권2호
• /
• pp.106-112
• /
• 2019

Flexible impact force sensors composed of piezoelectric PZT/PDMS composite sandwiched between Al/PET films were fabricated and their voltage signal characteristics were evaluated under varying impact forces for electronic mitt applications. The piezoelectric impact force sensor on an ethylene-vinyl acetate (EVA) substrate exhibited an output voltage difference of no greater than 40 mV a periodical impact test in with the impact load was increased by as much as 240 N by a restoration time of 5 s in a five-time experiment, implying good sensing ability. Moreover, the impact force sensor embedded four electronic mitts showed a reliable sensitivity of less than 1 mV/N and good repeatability under 100 N-impact force during a cycle test executed 10,000 times. This indicated that the fabricated flexible piezoelectric impact sensor could be used in electronic mitt applications. However, the relatively low elastic limit of substrate material such as EVA or poly-urethane slightly deteriorated the sensitivity of the impact sensor embedded electronic mitt at over 200 N-impact forces.

• 폴리머
• /
• 제35권3호
• /
• pp.203-209
• /
• 2011

표면이 매끄럽고 돌기가 있는 2가지 HDPE 지오멤브레인 덤벨형 시료에 두께 10% 간격으로 10~90% 깊이의 노치를 가하여 실험에 사용하였다. ISO 10722에 의거하여 부가하중 횟수를 변화시켜 시공시 손상의 실내 모사시험을 HDPE 지오브레인에 실시하였으며, 부가하중 횟수가 시공시 손상에 미치는 영향을 비교하였다. 항복응력과 변형률은 노지 깊이가 커짐에 따라 감소하였다. 손상된 그리고 노치를 가한 지오멤브레인을 응력균열시험에 사용하였으며, $50{\pm}1^{\circ}C$에서 pH 4와 12 용액에 침지시켜 항복응력 변화에 따른 응력균열저항성을 NCTL 시험을 통하여 고찰하였다. 인장 강도의 35% 이상에서 지오멤브레인은 응력균열에 취약함을 나타냈으며, 손상을 받은 그리고 노치를 가한 지오멤브레인 모두 같은 경향을 나타내었다. 특별히 노치를 가한 지오멤브레인의 경우 각각의 응력균열 조건에서 시공에 의해 손상된 지오멤브레인보다 낮은 강도를 나타내었다.

• 해양환경안전학회지
• /
• 제29권6호
• /
• pp.672-680
• /
• 2023

선박의 설계과정에 있어, 선박의 중량은 유체역학적 성능에 큰 영향을 미치는 가장 중요한 요소 중 하나이다. 선박은 일반적으로 최적의 흘수와 배수량을 갖는 하나의 조건으로 설계되지만, 실제로는 연료의 소비, 선박 평형수의 충전과 적재 조건과 같은 운항 활동으로 인해 선박의 중량 및 흘수가 일정 범위 내에서 바뀐다. 본 연구에서는 소형선박을 대상으로 3가지 하중조건에 따른 선박의 저항성능 변화를 모형실험과 수치해석을 통해 연구하였다. 마지막으로 2050년까지 CO2 배출 가스를 50% 감축한다는 국제해사기구(IMO) 목표를 따라 선박의 저항 성능을 개선하여 동력 요구 사항을 줄이기 위해 선박의 중량 변화에 따른 저항성능의 민감도를 연구하였다. 연구 결과, 선박의 중량변화에 따른 효과는 낮은 프루드 수에서 크게 나타나는 것으로 확인되며, 저항성능에 대한 연구 결과, 설계 흘수의 적재조건을 기준으로 배수량이 11.1% 증가하고, 흘수가 5% 증가한 Over load의 적재조건에서 운항 시 선체의 총 저항이 모형시험과 CFD 시뮬레이션에서 각각 15.97%, 14.31%까지 증가하는 것을 볼 수 있다.