• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.9
• /
• pp.68-73
• /
• 2013

In this paper, we proposed a readout circuit of pulse waveform and rate for a U-health system to monitor health condition. For long-time operation without replacing or charging a battery, either pulse waveform or pulse rate is selected as the output data of the proposed readout circuit according to health condition of a user. The proposed readout circuit consists of a simple digital logic discriminator and a dual-mode ADC which operates in the ADC mode or in the count mode. Firstly, the readout circuit counts pulse rate for 4 seconds in the count mode using the dual-mode ADC. Health condition is examined after the counted pulse rate is accumulated for 1 minute in the discriminator. If the pulse rate is out of the preset normal range, the dual-mode ADC operates in the ADC mode where pulse waveform is converted into 10-bit digital data with the sampling frequency of 1 kHz. These data are stored in a buffer and transmitted by 620 kbps to an external monitor through a RF transmitter. The data transmission period of the RF transmitter depends on the operation mode. It is generally 1 minute in the normal situation or 1 ms in the emergency situation. The proposed readout circuit was designed with $0.11{\mu}m$ process technology. The chip area is $460{\times}800{\mu}m^2$. According to measurement, the power consumption is $161.8{\mu}W$ in the count mode and $507.3{\mu}W$ in the ADC mode with the operating voltage of 1 V.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.8
• /
• pp.844-853
• /
• 2008

This paper describes the design of a FEM(Front End Module) having power detection function for mobile handset application. The designed FEM consists of a MMIC(Monolithic Microwave Integrated Circuits) power amplifier chip, SAW Tx filter and duplexer, diode power detector and stripline matching circuit. An LTCC(Low Temperature Co-fired Ceramics) technology is adopted for miniaturized FEM. The frequency band is $824{\sim}869$ MHz which is the uplink Tx band of the CDMA mobile system. The size of designed FEM is $7.0{\times}5.5{\times}1.5\;mm^3$, which is an ultra-small size even though the power detector circuit is included. All sub-components of FEM have been developed and measured in advance before being integrated into FEM. The measured output power and gain are 27 dBm and 27 dB, respectively. In addition, the measured ACPR characteristics are 46.59 dBc and 55.5 dBc at 885 kHz and 1.98 MHz offset, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.1
• /
• pp.76-84
• /
• 2012

In this paper, two kinds of E-plane microstrip-to-waveguide transitions are optimally designed and fabricated for combining output power from multiple small-power amplifiers in a WR-28 waveguide because conventional K connectors cause unnecessary insertion loss and adaptor loss. The transition design is based on target specifications such as a center frequency of 35 GHz, bandwidth of ${\pm}500MHz$, 0.1 dB insertion loss and 20 dB return loss. Performance variation caused by mechanical tolerance and assembly deviation is fully evaluated by three dimensional electromagnetic simulation. The fabricated back-to-back transitions with 16 mm and 26.57 mm interstage microstrip lines show insertion loss per transition of ~0.1 dB at 35 GHz and average 0.2 dB over full Ka band. Also the back-to-back transition shows return loss greater than 15 dB, which implies that the transition itself has return loss better than 20 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.352-361
• /
• 2010

In this paper, a compact 20 W block-up-converter for C-band satellite communication is designed and implemented. The designed block up-converter consists of an intermediate frequency circuit, a mixer and local oscillator, a driver amplifier, a solid-state power amplifier, waveguide circuits, and a power supply module. To reduce the size of the block-up-converter, all circuits are assembled within an housing, so its dimension is just $21{\times}14{\times}11cm^3$. Especially, the waveguide filter and microstirp-to-waveguide transition are easily implemented using an housing. Also, to meet spurious and harmonics specification, various compact microstrip filters including an elliptic filter are integrated. Measurement results show that the developed block up-converter has good electrical performances: the output power of 43.7 dBm, the minimum gain of 65 dB, the gain flatness of ${\pm}1.84$, the IMD3 of -35 dBc, and the harmonic level of -105 dBc.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.10
• /
• pp.769-778
• /
• 2017

In this paper, a self-interference signal cancellation(SIC) circult for In-band Full-Duplex has been developed and tested in RF/analog region. By use of this SIC circuit, a FM two-way radio has been developed working at FRS(Family Radio Service) band. The two-way radio device is transmitting the FM modulated signal and demodulating the wanted FM signal at the same time. A circulator is used to enable a single antenna to transmit and receive simuultaenously. The receiver circuit needs to cancel out the self-interference signal due to the transmit signal. A vector modulator(VM) is used to control the phase and magnitude of the esitmated signal. And in-phase and quadrature correlators are used to figure out the optimal coefficients of the VM to remove the self-interference signal according to the change of channel environment. In this work, SA58646 has been used as the FM transceiver, and the system is tested with a frequency of 465 MHz and a bandwidth of 12.5 kHz FM signal. The output power is 17.2 dBm at the antenna port, and the self intererence signal level is measured -49.2 dBm at the receiver end. Therefore the SIC level is measured by 66.4 dB.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.5
• /
• pp.69-75
• /
• 2001

In this paper, a fast and easy impedance matching method, which could give the impedance matching component for the general 1 or 2-port network was introduced. First, the entire network structure was defined which consists of the network part to be matched and the impedance matching part composed of inductors and capacitors. Next, the transmission matrix and input and output impedances of the entire network from the terminal impedance conditions were calculated, then the exact solutions for the matching components were obtained. To verify the efficiency of this method, this method was applied to the CDMA If band withdrawal weighted SAW transversal filter, and investigated the effects of the impedance matching before and after, through the simulation and experiment. As the result, the performance of a fractional bandwidth of 1.2%, insertion loss of 29 dB, and VSWR of 80 have improved to a factional bandwidth of 1.8％, insertion loss of 9 dB, VSWR of 3 at 85.38 MHz center frequency. The result shows that this impedance matching method could be used in the SAW devices and other types of 1 or 2-port network.

• Journal of the Korean Society of Costume
• /
• v.61 no.4
• /
• pp.117-137
• /
• 2011

This study analyzed historical records on silk tabby-ju(細), Si(總)- in a diachronic and spatial point of view. The historical records were written in Samguksagi(三國史記) of Korea, Eastern barbarian[東弟] section of Ershiwush(二十五史) of China and Ritkokusi(六國史)of Japan from the $4^{th}$ century to the early $10^{th}$ century. The study finally could reach the conclusions as follow. Firstly, records that fabrics like Ju were used were found in the Korean historical documents written on Balhae(渤海) of the $8^{th}$ century and Sllla(新羅) of the $9^{th}$ century. On the other hand, no official record on production of fabrics like Ju was found in the Japanese historical documents up to the $10^{th}$ century. Instead, there are some records that Si was produced and used for the first time in the $7^{th}$ century and it was rapidly spread in the $8^{th}$ century. In the $9^{th}$ century, the number of records on Si was sharply decreased and the importance of Si in the foreign-relation point of view also went down gradually. Secondly, records on using and trading with both Ju(細) and Si(總)in the foreign relation of two countries were shown from the $8^{th}$ century to the $9^{th}$ century. In the period, international exchange had been promoted among Balhae, Silla and ancient Japan. In the $9^{th}$ century, fabrics like Ju of ancient Korea was introduced to ancient Japan ancient Japanese people could not manufacture Ju by themselves at that time. On this account, we assumed that ancient Japanese people might consider Ju as high quality fabric rather than Si that had been used as general fabric. Meanwhile, it is found that Japan presented various kinds of Si to Balhae and Silla from the early $8^{th}$ century. As the foreign relation between Sllia and ancient Japan got weaker in the mid-$8^{th}$ century, frequency and amount of supplying Si to Balhae were relatively increased. Besides Si, Balhae was given a lot of silk yarn and floss. These fabrics presumably were used as raw material of Ju in Balhae because Balhae got low output of silk due to its geographical condition.

• The KIPS Transactions:PartD
• /
• v.18D no.6
• /
• pp.501-508
• /
• 2011

A knowledge map, which has been recently applied in various fields, is discovering characteristics hidden in a large amount of information and showing a tangible output to understand the meaning of the discovery. In this paper, we suggested a knowledge map for research trend analysis based on keyword-relation networks which are constructed by using a database of the domestic journal articles in the computer engineering field from 2000 through 2010. From that knowledge map, we could infer influential changes of a research topic related a specific keyword through examining the change of sizes of the connected components to which the keyword belongs in the keyword-relation networks. In addition, we observed that the size of the largest connected component in the keyword-relation networks is relatively small and groups of high-similarity keyword pairs are clustered in them by comparison with the random networks. This implies that the research field corresponding to the largest connected component is not so huge and many small-scale topics included in it are highly clustered and loosely-connected to each other. our proposed knowledge map can be considered as a approach for the research trend analysis while it is impossible to obtain those results by conventional approaches such as analyzing the frequency of an individual keyword.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.2D
• /
• pp.137-145
• /
• 2012

According to the National Police Agency, the total number of traffic accidents which occurred in 2010 was 226,878. Intersection accidents accounts for 44.8%, the largest portion of the entire traffic accidents. An research on the signalized intersection is constantly made, while an research on the unsignalized intersection is yet insufficient. This study selected traffic volume, road width, and sight distance as the input variables which affect unsignalized intersection accidents, and number of accidents as the output variable to build a model using ANFIS(Adaptive Neuro-Fuzzy Inference System). The forecast performance of this model is evaluated by comparing the actual measurement value with the forecasted value. The compatibility is evaluated by R2, the coefficient of determination, along with Mean Absolute Error (MAE) and Mean Square Error (MSE), the indicators which represent the degree of error and distribution. The result shows that the $R^2$ is 0.9817, while MAE and MSE are 0.4773 and 0.3037 respectively, which means that the explanatory power of the model is quite decent. This study is expected to provide the basic data for establishment of safety measure for unsignalized intersection and the improvement of traffic accidents.

• Journal of Biosystems Engineering
• /
• v.25 no.2
• /
• pp.97-106
• /
• 2000

To develop the grain moisture meter using microwave free space transmission technique, a 10.5GHz microwave signal with the power of 11mW generated by an oscillar with a dielectric resonator is transmitted to an isolator and radiated from a transmitting $2{\times}2$ microstrip patch array antenna into the sample holder filled with the 12 to 26%w.b. of Korean Hwawung paddy rice. the microwave signal, attenuated through the grain with moisture, is collected by a receiving $2{\times}2$ microstrip patch array antenna and detected using a Shottky diode with excellent high frequency characteristic. A pair of light and simple microstrip patch array antenna for measurement of grain moisture content is designed and implemented on atenflon substrate with trleative dielectric constant of 2.6 and thickness of 0.54 by using Ensemble ver. 4.02 software. The aperture of microstrip patch arrays is 41 mm width and 24mm high. The characteristics of microstrip patch antenna such as grain. return loss, and bandwidth are 11.35dBi, -38dB and 0.35GHz($50^{\circ}$ at far-field pattern of E and H plane. The width of the sample holder is large enough to cover the signal between the antennas temperature and bulk density respectively. The calibration model for measurement of grain moisture content is proposed to reduce the effects of fluectuations in bulk density and temperature which give serious errors for the measurements . From the results of regression analysis using the statistically analysis method, the moisture content of grain samples (MC(%)) is expressed in terms of the output voltage(v), temperature (t), and bulk density of samples(${\rho}b$)as follows ;$$MC(%)\;=\;(-3.9838{\times}10^{-8}{\times}v^{3}+8.023{\times}10^{-6}{\times}v^{2}-0.0011{\times}v-0.0004{\times}t+0.1706){\frac{1}{{\rho}b}}{\times}100$ Its determination coefficient, standard error of prediction(SEP) and bias were found to be 0.9855, 0.479%w.b. and -0.0.369 %w.b. respectively between measured and predicted moisture contents of the grain samples.