• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.355-356
• /
• 2020

본 논문에서는 PFC와 LLC공진형 컨버터로 구성되는 단상 AC/DC 정류기 시스템에서 발생하는 출력전압 120Hz 리플 저감에 관한 전향보상 제어기법을 제안한다. 제안하는 방법은 입/출력 전력 차이를 이용하여 DC-link의 전압 리플을 계산하고, 선형화된 LLC공진형 컨버터의 주파수 이득 곡선을 기반으로 120Hz에 대한 리플 성분을 전향 보상하여 저감 시키는 방법이며, 시뮬레이션을 이용하여 타당성을 검증하였다.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.724-729
• /
• 1998

In general, a single-phase current-fed PWM inverter using IGBTs has some unique advantages for small scale distributed utility-interactive power supply system as compared with voltage-fed PWM inverter. In particular, this is more suitable and acceptable for a non-isolated type utility-interactive power conditioner, which is going to be widely used for residential solar photovoltaic (PV) power generation system in Japan. However, this current-fed PWM inverter has a significant disadvantage. The output current of this inverter includes large harmonic contents when the inductance of smoothing reactor in its DC side is not large enough to eliminate its current ripple components of this inverter. In order to overcome this problem, a new conceptual pulse area modulation scheme for this inverter is introduced in difference with conventional PWM strategy. This paper presents a new effective control implementation of this PV power conditioner which is able to reduce the harmonic component in the output current produced by the single-phase current-fed PWM inverter even when the ripple current in the smoothing DC reactor is relatively large. The operating principle of the proposed control strategy introdued for this inverter system is described, and its simulation results are evaluated and discussed herein.

• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.399-410
• /
• 2015

A 6.5 V/50 kA high-frequency switching power supply (HSPS) system composed of 10 power modules is developed to meet the requirements of copper-foil electrolysis. The power module is composed of a two-leg pulse width modulation (PWM) rectifier and a DC/DC converter. The DC/DC converter adopts two full-wave rectifiers in parallel to enhance the output. For the two-leg PWM rectifier, the ripple of the DC-link voltage is derived. A composite control method with a ripple filter is then proposed to effectively improve the performance of the rectifier. To meet the process demand of copper-foil electrolysis, the virtual impedance-based current-sharing control method with load current full feedforward is proposed for n-parallel DC/DC converters. The roles of load current feedforward and virtual impedance are analyzed, and the current-sharing control model of the HSPS system is derived. Virtual impedance is used to adjust the current-sharing impedance without changing the equivalent output impedance, which can effectively reduce current-sharing errors. Finally, simulation and experimental results verify the structure and control method.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.547-550
• /
• 2004

An interleaved single-stage power-factor-correction (PFC) AC/DC converter is presented in this paper. The proposed converter is combined by two single-stage AC/DC converters based on flyback converter Each PFC stage operates in discontinuous conduction mode (DCM). By exploiting the interleaving technique, the input ripple current and output ripple voltage are reduced. The proposed converter complied with EN/1EC61000-3-2 harmonic regulations achieves high efficiency and low cost. The performance of the proposed converter was evaluated on a 180W $(90W\times2,\;24V,\;7.5A)$ experimental prototype.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.529-531
• /
• 2008

Generation system using regenerative energy like photovoltaic, fuelcell is increased, PCS technology coming into the spotlight. The efficiency of DC-DC converter as part of the PCS is very important, multi-phase boost converter has more advantage than other topology. Input current of the multi-phase boost converter is divided into two inductor current because of parallel structure of the boost converters, thus it has features of decreasing input current ripple and output voltage ripple. Also multi-phase boost converter with soft switching can decrease switching loss using ZCS and ZVS. In this paper, simulation and experiment are performed to verify operation of the proposed converter, and efficiencies of the conventional and proposed converter are compared.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.182-183
• /
• 2013

In the design of the fuel cell charger, it is important to find out the suitable topology and to design the converter to guarantee the performance of the fuel cell as well as the battery. Most of the chargers developed so far have used step-down converters. However, since the small fuel cell stack can only generate a low voltage, it is required to use the step-up converter to charge the battery. In this paper, a modified non-isolated boost charger topology for the Proton Exchange Membrane Fuel Cell (PEMFC) is proposed to meet the strict ripple requirements for the battery charge and its control method by using PI controller is detailed. The feasibility of the proposed topology and its control method is then verified by the experiments.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.5
• /
• pp.31-38
• /
• 2014

Maximum power point tracking method is very important to enhance efficiency of photovoltaic system. Meanwhile a lot of research about MPPT has been studied and developed new one better than a method of the past. This paper deals with Perturb and Observation that are most commonly used. Tracking parameter changed PV voltage for PV current and it was simulated with P-SIM program. The P&O tracking method to use current for parameter lows ripple rate of output and enhances response rate of tracking. Through this study, it has been demonstrated that method using current for tracking parameter is effective.

• Proceedings of the KAIS Fall Conference
• /
• 2004.06a
• /
• pp.193-197
• /
• 2004

The four-leg Voltage Source Converter(VSC) can use the DC link voltage effectively by the 3-D SVPWM method. Hence the DC battery voltage can be reduced by $15\%$ in comparison to that of the conventional line-interactive UPS system. In this paper a novel line interactive Uninterruptible Power Supply(UPS) using the two four-leg VSCs is proposed. One VSC is in parallel with the ac link reactor of the power source side, and the other is in series with the load. The parallel four-leg voltage source inverter controls the three-phase line voltage independently in order to control the line reactor current indirectly. It eliminates the neutral line current and the active ripple power of the source side using the pqr theory so that unity power factor and the sinusoidal source current can be achieved even though both the source and the load voltages have zero sequence components. The series four-leg voltage source inverter compensates the line voltage and allows it to be balanced and harmonic-free. Both of the parallel and series four-leg voltage source inverters always act as independently controllable voltage sources, so that the three-phase output voltage shows a seamless transition to the backup mode. The feasibility of the proposed UPS system has been investigated and verified through computer simulations results.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.605-610
• /
• 1991

In inverter system for driving induction motor, the output harmonics are hamrful in induction motor drive because it leads to ripple torque and induction interference. For electrical drives using PWM(Pulsewidth Modulation) inverters and ac motors, the methods for efficiency optimal control have been developed. In this paper, two different PWM methods for inverter and voltage control technique are described. In order to reduce or minimize losses, various forms of PWM strategy such as, PM (Positive Modulation) and NM (Negative Modulation) are discussed. The results show the feasibility of obtaining practically sinusoidal output waveforms which are highly desirable in most inverter application.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.4
• /
• pp.483-489
• /
• 2009

Electrolytic capacitors are used in variety of equipments as smoothening element of the power converters because it has high capacitance for its size and low price. Electrolytic capacitors, which is most of the time affected by aging effect, plays a very important role for the power electronics system quality and reliability. Therefore it is important to estimate the parameter of an electrolytic capacitor to predict the failure. This objective of this paper is to propose a new method to detect the rise of equivalent series resistor(ESR) in order to realize the online failure prediction of electrolytic capacitor for DC output filter of power converter. The ESR of electrolytic capacitor estimated from RMS result of filtered waveform(BPF) of the ripple capacitor voltage/current. Therefore, the preposed online failure prediction method has the merits of easy ESR computation and circuit simplicity. Simulation and experimental results are shown to verify the performance of the proposed on-line method.