• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.5
• /
• pp.967-973
• /
• 1997

In this paper, the designed and fabrication of a K-band push-push oscillator using miniaturized hairpin resonator have been presented. One experimenal oscillator has been designed and fabricated for K-band point-to-point operation. the miniaturized harpin resonator has been analyzed theoretically and simulated by MPIE(Mixed Potential Integral Equation) method. With this results, the analysis of hairpin resonator which coupled microstrip line has been carried out with transmission-mode using this results. an optimized output matching network for the suppression of the fundamental and the 3rd order harmonic was acquired by using a nonlinear analysis method. The fabricated oscillator shows the output power of -2.28dBm, the fundamental frequency suppression of -19dBc, the 3rd order harmonic suppressionof -24dBc and 0.33 percent effiiency at 22.8GHz. The experimental outputs are in good agreement with the theoretical and simulated results.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1425-1427
• /
• 2005

In this paper, with loosely coupled transformer series-parallel resonant type DC/DC converter is analyzed. To get more efficient operating mode of the series-parallel resonant type DC/DC converter, theoretical analysis using normalized parameters are accepted. The proposed converter must be operated in Pulse Frequency Modulation(PFM) switching pattern for the Zero Voltage Switching(ZVS) operation. According to PFM control method, the output voltage of the proposed circuit can be controlled.

• Journal of Power Electronics
• /
• v.18 no.1
• /
• pp.195-203
• /
• 2018

In the variable speed Wind Turbine based on ElectroMagnetic Coupler (WT-EMC), a synchronous generator is coupled directly to the grid. Therefore, like conventional power plants, WT-EMC is able to inherently support grid frequency. However, due to the reduced inertia of the synchronous generator, WT-EMC is expected to be controlled to increase its output power in response to a grid frequency drop to support grid frequency. Similar to the grid frequency support control of Type 3 or Type 4 wind turbine, inertial control and droop control can be used to calculate the WT-EMC additional output power reference according to the synchronous generator speed. In this paper, an experimental platform is built to study the grid frequency support from WT-EMC with inertial control and droop control. Two synchronous generators, driven by two induction motors controlled by two converters, are used to emulate the synchronous generators in conventional power plants and in WT-EMCs respectively. The effectiveness of the grid frequency support from WT-EMC with inertial control and droop control responding to a grid frequency drop is validated by experimental results. The selection of the grid frequency support controller and its gain for WT-EMC is analyzed briefly.

• Journal of the Korean Physical Society
• /
• v.73 no.9
• /
• pp.1362-1369
• /
• 2018

A method aimed at improving the beam-wave interaction efficiency by changing the coupling slot configuration has been proposed in the study of extended interaction oscillators (EIOs). The dispersion characteristics, coupling coefficient and interaction impedance of the high-frequency structure based on different types of coupling slots have been investigated. Four types of coupled cavity structures with different layouts of the coupling slots have been compared to improve the beam-wave interaction efficiency, so as to analyze the beam-wave interaction and practical applications. In order to determine the improvement of the coupling slot to a coupled cavity circuit in an EIO, we designed four nine-gap EIOs based on the coupled cavity structure with different coupling slot configurations. With different operating frequencies and voltages takes into consideration, beam voltages from 27 to 33 kV have been simulated to achieve the best beam-wave interaction efficiency so that the EIOs are able to work in the $2{\pi}$ mode. The influence of the Rb and the ds on the output power is also taken into consideration. The Rb is the radius of the electron beam, and the ds is the width of the coupling slot. The simulation results indicate that a single-slot-type EIO has the best beam-wave interaction efficiency. Its maximum output power is 2.8 kW and the efficiency is 18% when the operating voltage is 31 kV and electric current is 0.5 A. The output powers of these four EIOs that were designed for comparison are not less than 1.7 kW. The improved coupling-slot configurations enables the extended interaction oscillator to meet the different engineering requirements better.

• Journal of Power Electronics
• /
• v.17 no.1
• /
• pp.222-231
• /
• 2017

In this paper, a new architecture for a cost-effective power conditioning systems (PCS) using a single-sourced asymmetric cascaded H-bridge multilevel inverter (MLI) for photovoltaic (PV) applications is proposed. The asymmetric MLI topology has a reduced number of parts compared to the symmetrical type for the same number of voltage level. However, the modulation index threshold related to the drop in the number of levels of the inverter output is higher than that of the symmetrical MLI. This problem results in a modulation index limitation which is relatively higher than that of the symmetrical MLI. Hence, an extra voltage pre-regulator becomes a necessary component in the PCS under a wide operating bias variation. In addition to pre-stage voltage regulation for the constant MLI dc-links, another auxiliary pre-regulator should provide isolation and voltage balance among the multiple H-bridge cells in the asymmetrical MLI as well as the symmetrical ones. The proposed PCS uses a single-ended DC-DC converter topology with a coupled inductor and charge-pump circuit to satisfy all of the aforementioned requirements. Since the proposed integrated-type voltage pre-regulator circuit uses only a single MOSFET switch and a single magnetic component, the size and cost of the PCS is an optimal trade-off. In addition, the voltage balance between the separate H-bridge cells is automatically maintained by the number of turns in the coupled inductor transformer regardless of the duty cycle, which eliminates the need for an extra voltage regulator for the auxiliary H-bridge in MLIs. The voltage balance is also maintained under the discontinuous conduction mode (DCM). Thus, the PCS is also operational during light load conditions. The proposed architecture can apply the module-integrated converter (MIC) concept to perform distributed MPPT. The proposed architecture is analyzed and verified for a 7-level asymmetric MLI, using simulation results and a hardware implementation.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.114-116
• /
• 1993

A novel Neural networks controller for Buck type DC-DC converter is presented and compared with the operation of sliding node coupled several control strategies for the converter. The connection weights of neural networks are trained by error back propagation algorithm. The behavior of the control system that arises fred the use of those methods is analyzed from the viewpoint of dynamic and steady state errors and simulation results are presented.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.9
• /
• pp.2272-2283
• /
• 1994

In scanning tunneling microscopy, the piezoelectric actuator is popuilarly used in stacked type as it can provide remarkable positioning resolution and stiffness. The actuator, however, exhibits a considerable amount of hystereic nonlinearity, resulting in losses of overall measuring accuracy when a linear model is used for its control and calibration, In this study, a nonlinear model is proposed for predicting the precise relationship between the input connand voltage and the output displacement of the actuator itself, cross-coupled electrical behaviours of the driving circuit with the actuator, and mechanical characteristics of the driven components of the actuator. Finally experimental results prove that the nonlinear model enhances the measuring of scanning tunneling microscopy by an order ten in comparison with a conventional linear model.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.9
• /
• pp.666-672
• /
• 2003

In this paper, we described the fabrication and the performance of wavelength tunable distributed bragg reflector (DBR) laser diode (LD), having different waveguide coupling mechanisms; integrated-twin-guide (ITG) DBR-LD and butt coupled (BT) DBR-LD. This deviceis fabricated by metal organic vapor phase epitaxy (MOVPE) growth and planar buried heterostructure (PBH)-type transverse current confinement structure. The result of measurement, the optical performance of BT-DBR-LD is better over 2 times than that of ITG-DBR-LD at the variation of threshold current and output power, and slop efficiency due to the higher coupling efficiency of the butt coupled structure than the integrated twin guide structure. The maximum wavelength tuning range is about 7.2nm for ITG DBR-LD and 7.4nm for BT DBR-LD. Both types of lasers have a very high yield of single mode operation with a side-mode suppression ratio of more than 35dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.3
• /
• pp.432-438
• /
• 2001

In this paper, after applying Defected Ground Structure(DGS) to DC block, changes of gap and length of λ/4 coupled line are investigated by EM simulation and fabrication. As a result, on condition of the same output with the case using typical DC block, the gap between λ/4 coupled line is widen from 0.1 mm to 0.46 mm by 0.36 mm and the length of λ/4 coupled line gets shorter from 17.7 mm to 13.2 mm by 4.5 mm. Also three type power amplifiers using blocking capacitor, typical DC block and DGS DC block are fabricated and investigated. At first, when S parameter characteristics of each amplifier are considered at frequency band of 3.2 +-0.O5 GHz, every amplifier has similar characteristics of gain and S parameter. Second when the output power of amplifiers is 25 dBm after putting CW signal of 3.2 GHz into three type amplifiers, the difference of dominant signal and 2nd harmonic signal using blocking capacitor, typical DC block and DGS DC block is each -44.83 dBc, -66.84 dBc and -64.33 dBc. Therefore harmonic characteristics of amplifiers using typical DC block and DGS DC block is almost same.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.1
• /
• pp.147-152
• /
• 2008

This paper has been fabricated the two different type of variable attenuators using a characteristics of a 3 dB directional coupler and pin diodes. One was not analyzed using the conventional even-odd modes but used simple two-port techniques. The resulting scattering parameters described operation characteristics for the general case where the terminating impedances are equal and unequal. After analyzing resistor role of the ${\pi}$ type fixed attenuator. this paper used a pin diode instead of a resistor. The variable attenuators were fabricated using pin diodes for current-controlled attenuation on the coupled ports of a 3 dB branch-line coupler and ${\pi}$ type fixed attenuator. The realized variable attenuators have more than 33 dB attenuation ranges at 2.1 GHz. and the input and output reflection coefficients are less than -13 dB. These results could be applied to mobile communication systems. It can be varied gain of the power amplifier according to change a outdoor environmental temperature and improved linearity.