• Journal of Power System Engineering
• /
• v.20 no.4
• /
• pp.75-82
• /
• 2016

In this paper, we developed a 3D printing system using a photo-curing resin in order to reduce the surface roughness of a sculpture produced with the 3D printer. Using the pattern of the resulting variable thickness, that gave rise to a stepped shape, and the area error of the photo-curable sculpture, a study was carried out for the process to reduce the surface roughness. At a given value of stage velocity (40~70 mm/s) and output air pneumatic pressure (20~60 kPa), the minimum pattern thickness of the pattern was achieved $65{\mu}m$ and the maximum pattern thickness of up to $175{\mu}m$. To increases the pattern resolution to about $40{\mu}m$, the process conditions should be optimized. 3D surface Nano profiler was used to find the surface roughness of the sculpture that was measured to be minimum $4.7{\mu}m$ and maximum $8.7{\mu}m$. The maximum surface roughness was reduced about $1.2{\mu}m$ for the maximum thickness of the pattern. In addition, a FDM was used to fabricate the same sculpture and its surface roughness measurements were also taken for comparison with the one fabricated using photo-curing. Same process conditions were used for both fabrication setups in order to perform the comparison efficiently. The surface roughness of the photo-curable sculpture is $5.5{\mu}m$ lower than the sculpture fabricated using FDM. A certain circuit patterns was formed on the laminated surface of the photo-curable sculpture while there was no stable pattern on the laminated surface of the FDM based sculpture the other hand.

• Journal of Korea Water Resources Association
• /
• v.43 no.6
• /
• pp.507-516
• /
• 2010

The purpose of this study is to propose the alternative development method by means of determining the optimal project size from the economic viewpoint, improving the existing method depending on engineering aspects. To this end, this study defined the flood mitigation projects as the production activities carried out by inputs and outputs, and proposed the alternative development method on the basis of optimizing input and output combinations. This paper, as the case study of the proposed method, developed alternatives for the flood mitigation planning of Youngsan River Basin by determining the optimal project scale. As the result of determining optimal project size, the net benefit of the optimal alternative tended to be dependent on the net benefits of the large individual proposals. Due to such problem, the effect of relatively small individual proposals are underestimated and possibly be excluded from the optimal alternative, which may result in exclusion of the potential damaged regions protected by them from the flood mitigation project. Thus for the selective flood protection by region, individual proposals need to be categorized into the global measures and local measures according to the flood protection area.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.1
• /
• pp.14-21
• /
• 2011

A 10b 500MS/s $0.13{\mu}m$ CMOS ADC is proposed for 4G wireless communication systems such as a LTE-Advanced and SDR The ADC employs a calibration-free single-channel folding architecture for low power consumption and high speed conversion rate. In order to overcome the disadvantage of high folding rate, at the fine 7b ADC, a cascaded folding-interpolating technique is proposed. Further, a folding amplifier with the folded cascode output stage is also discussed in the block of folding bus, to improve the bandwidth limitation and voltage gain by parasitic capacitances. The chip has been fabricated with $0.13{\mu}m$ 1P6M CMOS technology, the effective chip area is $1.5mm^2$. The measured results of INL and DNL are within 2.95LSB and l.24LSB at 10b resolution, respectively. The SNDR is 54.8dB and SFDR is 63.4dBc when the input frequency is 9.27MHz at sampling frequency of 500MHz. The ADC consumes 150mW($300{\mu}W/MS/s$) including peripheral circuits at 500MS/s and 1.2V(1.5V) power supply.

• Journal of the Korea Convergence Society
• /
• v.8 no.8
• /
• pp.147-154
• /
• 2017

The purpose of this study is to calculate and compare administered activities(MBq) and effective dose(mSv) of the various pediatric dose formulas of pediatric nuclear medicine and to provide base data for the criteria of the optimal administered activities. This study compares dosages and effective doses of 5 types of pediatric dose formulas(Clark rule, Area rule, Webster rule, Young rule, Solomon(Fried) rule) based on the dosage for adults of 2 types of radiopharmaceuticals($^{99m}Tc$-MDP, $^{99m}Tc$-Pertechnetate). The administered activities in adults, which is the criteria for calculating the Pediatric administered activities, used the value from the 'Nuclear Medicine' written by J-G Jeong & M-Ch Lee. and the administered activities by the radioactivity per effective dose(mSv/MBq) of the radiopharmaceuticals for calculating the effective dose used the value from ICRP 80 and the UNSCEAR 2008 Report. As a result of the study, the output of Young rule is the lowest, and its difference between other formulas is from minimum 1.7 times to maximum 3,4 times. The difference between administered activities of $^{99m}Tc$-MDP is maximum 309.9MBq and the effective dose is 3.76mSv. $^{99m}Tc$-Pertechnetate showed the figure at the maximum 154.9MBq and the effective dose has a difference of 5.50mSv. Since the pediatric dose formulas differ not only in administered activities but also in effective doses, the optimal administered activities have to be developed for optimization of medical radiation.

• 대한공업교육학회지
• /
• v.40 no.1
• /
• pp.180-200
• /
• 2015

The problems current robotic technology education class has are the students with different basic background knowledge levels and the class based on the instructional teaching method. This study shows the implementation of the student teams achievement divisions (STAD) learning model into an introductory robotic technology education class to resolve the problems in the current robotic technology class. The STAD learning model focuses on the ability of each team member with different knowledge levels and make team members help each other through class activities such as assignments and a project. All members get rewarded by their performance output as a team in a course grade. The outputs of STAD learning models were measured by paired sample t-test as pre-test and post-test in terms of students's transition on basic knowledge for robotic technology, students' attitudinal transition on teaching robotic technology class, and students' competencies and self-efficacy on related subject areas. The study participants were 22 pre-service technology teachers at a university. The results show that all four measured areas were improved significantly, compared to pre-test with respect to the means scores of each measurement area. The STAD learning model could be an alternate for the current robotic technology class to deliver the better class outcomes for students under the specific circumstances.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.69-74
• /
• 2018

Large industrial motors require a large area because of the high risk of shutdown accidents and large industrial accidents due to the lowering of the dielectric strength of the armature windings and overheating problems. Therefore, there is a demand for a large-capacity motor that has small size, light weight, and excellent dielectric strength compared with conventional motors. Superconducting motors have advantages of high efficiency and output power, low size, low weight, and improved stability. This results from greatly increasing the magnetic field generation by using superconductive field coils in rotating machines such as generators and motors. It is very important to design and analyze the cooling system to lower the critical temperature of the wires to achieve superconducting performance. In this study, a field loss analysis and low-temperature heat transfer analysis of the cooling system were performed through the conceptual design of a 100-HP high-temperature superconducting synchronous motor. The field loss analysis shows that a uniform pore magnetic flux density appears when high-temperature superconducting wire is used. The low-temperature heat transfer analysis for gaseous neon and liquid neon showed that a flow rate of 1 kg/min of liquid neon is suitable for maintaining low-temperature stability of the high-temperature superconducting wire.

• Journal of the Korean Society of Radiology
• /
• v.12 no.3
• /
• pp.335-341
• /
• 2018

With the improvement of medical state, patients' expectations for the most advanced medical equipment are increasing. Particularly, Magnetic Resonance Image (MRI) is used as one of the core image diagnosis methods in all clinical area. However, it has been reported that many of patients who go through the examination suffer from anxiety to the severe noise level during the examination. In this study, both the noise reduction evaluation of headsets with sound-blocking materials added to existing sound-absorbing materials and the existence of sound blocking materials as artifacts on the examination image are tested. An MRI test noise is recorded as a speaker by cross-ordination the sound material (sponge) and the sound material (acrylic plate, copper plate, and 3D copper plate) inside the headset made from 3D pring. A quantitative assessment of headsets showed that the average headset value was 81.8 dB. The average dB value of the most soundproof material combination(Copper, acrylic plate, sponge, sponge) headsets on headsets with added charactering material was measured at 70.4 dB, and MRI showed that the copper was diamagnetic substance and excluded. The second most soundproof headset(Sponge, acrylic plate, 3D copper plate, sponge) was measured at 70.6 dB and MRI showed no artifacts. The same simulation of the material printed with a 3D copper PLA containing approximately 40 % copper powder resulted in no artifacts, therefore, the material output as a 3D printing was better suited for use. For MRI related research, the mutual development of 3D printing is highly anticipated.

• Journal of Korea Water Resources Association
• /
• v.38 no.4 s.153
• /
• pp.301-311
• /
• 2005

The purpose of this study is to assess the quantitative effect of stream discharge due to land use changes. The upstream watershed of Pyeongtaek gauging station of Anseong-cheon ($592.6\;km^2$) was adopted. To accomplish the purpose, firstly, trace land use changes for the selected watershed which have some changes of land use by using Landsat images of 1986 and 1999 of the watershed and secondly, analyse the quantitative effect of stream discharge due to land use changes by applying GIS- based distributed hydrologic model KIMSTORM. The model was calibrated and verified at 2 locations (Pyeongtaek and Gongdo) by comparing observed with simulated discharge results for 7 storm events from 1998 to 2003. Model output was designed to provide information of land use impact on runoff components in the watershed and the sensitivity of impact level of each land use category on storm runoff. Land use impact was evaluated with the land use data sets for 1986 and 1999 for the same rainfall condition (160.5 mm). Area decrease of 4.8 percent of forest and 4.0 percent of paddy field during 13 years (1986 - 1999) within the watershed caused a 30.3 percent increase of peak runoff and a 9.3 percent increase of runoff volume.

• Journal of Biosystems Engineering
• /
• v.37 no.3
• /
• pp.155-165
• /
• 2012

This study was performed to offer the data for design of the seedling bed transfer equipment to make the automation of working process in a plant factory. The seedling bed transfer equipment pushing the seedling bed with bearing wheels on the rail for interconnecting each working process by a pneumatic cylinder was made and examined. The examined transfer force to push the seedling bed with a weight of 178.9 N by the pneumatic cylinder with length of 60 cm and section area of 5 $cm^2$ was measured by experiments. The examined transfer forces was compared with theoretical ones calculated by the theoretical formula derived from dynamic system analysis according to the number of the seedling bed and pushing speed of the pneumatic cylinder head at no load. The transfer function of the equipment with the input variable as the pushing speed $V_{h0}$(m/s) and the output variable as the transfer force f(t)(N) was represented as $F(s)=(V_{h0}/k)(s+B/M)/(s(s^2+Bs/M+1/(kM))$ where M(kg), k(m/N) and B(Ns/m) are the mass of the bed, the compression coefficient of the pneumatic cylinder and the dynamic friction coefficient between the seedling bed and the rail, respectively. The examined transfer force curves and the theoretical ones were represented similar wave forms as to use the theoretical formular to design the device for the seedling bed transfer. The condition of no vibration of the transfer force curve was $kB^2>4M$. The condition of transferring the bed by the repeatable impact and vibration force according to difference of transfer distance of the pneumatic cylinder head from that of the bed was as $Ce^{-\frac{3{\pi}D}{2\omega}}<-1$, where ${\omega}=\sqrt{\frac{1}{kM}-\frac{B^2}{4M^2}}$, $C=\{\frac{\frac{B}{2M}-\frac{1}{kB}}{\omega}\}$, $D=\frac{B}{2M}$. The examined mean peak transfer force represented 4 times of the stead state transfer force. Therefore it seemed that the transfer force of the pneumatic cylinder required for design of the push device was 4Bv where v is the pushing speed.

• Science of Emotion and Sensibility
• /
• v.15 no.4
• /
• pp.503-516
• /
• 2012

According to the researches of robot and software agent until now, computational emotion model is dependent on system, so it is hard task that emotion models is separated from existing systems and then recycled into new systems. Therefore, I introduce the Engine of computational Emotion model (shall hereafter appear as EE) to integrate with any robots or agents. This is the engine, ie a software for independent form from inputs and outputs, so the EE is Emotion Generation to control only generation and processing of emotions without both phases of Inputs(Perception) and Outputs(Expression). The EE can be interfaced with any inputs and outputs, and produce emotions from not only emotion itself but also personality and emotions of person. In addition, the EE can be existed in any robot or agent by a kind of software library, or be used as a separate system to communicate. In EE, emotions is the Primary Emotions, ie Joy, Surprise, Disgust, Fear, Sadness, and Anger. It is vector that consist of string and coefficient about emotion, and EE receives this vectors from input interface and then sends its to output interface. In EE, each emotions are connected to lists of emotional experiences, and the lists consisted of string and coefficient of each emotional experiences are used to generate and process emotional states. The emotional experiences are consisted of emotion vocabulary understanding various emotional experiences of human. This study EE is available to use to make interaction products to response the appropriate reaction of human emotions. The significance of the study is on development of a system to induce that person feel that product has your sympathy. Therefore, the EE can help give an efficient service of emotional sympathy to products of HRI, HCI area.