• Journal of Periodontal and Implant Science
• /
• 제46권1호
• /
• pp.2-9
• /
• 2016

Purpose: Porphyromonas gingivalis and Tannerella forsythia have been implicated as the major etiologic agents of periodontal disease. These two bacteria are frequently isolated together from the periodontal lesion, and it has been suggested that their interaction may increase each one's virulence potential. The purpose of this study was to identify proteins on the surface of these organisms that are involved in interbacterial binding. Methods: Biotin labeling of surface proteins of P. gingivalis and T. forsythia and liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis was performed to identify surface proteins involved in the coaggregating activity between P. gingivalis and T. forsythia. Results: It was found that three major T. forsythia proteins sized 161, 100, and 62 kDa were involved in binding to P. gingivalis, and P. gingivalis proteins sized 35, 32, and 26 kDa were involved in binding to T. forsythia cells. Conclusions: LC-MS/MS analysis identified one T. forsythia surface protein (TonB-linked outer membrane protein) involved in interbacterial binding to P. gingivalis. However, the nature of other T. forsythia and P. gingivalis surface proteins identified by biotin labeling could not be determined. Further analysis of these proteins will help elucidate the molecular mechanisms that mediate coaggregation between P. gingivalis and T. forsythia.

• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.190-196
• /
• 2004

ACR(All Clear Reflector), also widely referred to as FFR(Free Form Reflector), were designed in general and intelligent ways using a NUDBS surface for the mathematical modelling of the reflector shape and artificial intelligence as the optimum design algorithm. An ACR, which consists of a continuous surface reflector and clear outer lens, offers styling advantages and provides a high quality light performance. The clear outer lens of an ACR remains efficient even with a highly inclined shape, as in the design of a sports car, as well as the complete clearness of the reflector surface eliminates the nuisance of stray light caused by the steps between adjacent segments of multi-faced reflectors. The application of an ACR to low beam lamp was so sucessful to obtain the sharp cut-off with the lens-free single-surfaced-smooth reflector. The design technique of ACR was tested with all types of lamps, including low beams, high beams, and fog lamps.

• 한국의류산업학회지
• /
• 제3권5호
• /
• pp.473-478
• /
• 2001

The newly developed cone drum twister is one of the outer surface contacting friction-twisting devices in false-twist texturing. An investigation of the drag angle for the newly developed cone drum twister texturing mechanism is reported. An analysis is given from which equations can be derived that relate to the conical angle of cone drum, wrapping angle, drag angle, and yam helix angle. Theoretical values of drag angle are calculated and discussed. It is shown that, as the helix angle and the projected wrapping angle increases, the drag angle also increases slowly until the helix angle of $40^{\circ}$ but after the helix angle of $40^{\circ}$ the drag angle increases rapidly. Furthermore the higher the projected wrapping angle and conical angle, the higher the drag angle of friction surface.

• 한국CDE학회논문집
• /
• 제11권1호
• /
• pp.20-26
• /
• 2006

This paper presents a procedure to compute pencil curves from a triangular mesh which is offset with the radius of a given ball-end mill. An offset triangular mesh has numerous self-intersections caused by an abundance of invalid triangles, which do not contribute to the valid CL-surface. Conceptually, we can obtain valid pencil curves by combining all intersections tying on the outer skin of the offset triangular mesh, i.e., the valid CL-surface. The underlying concept of the proposed algorithm is that visible intersections are always valid for pencil curves, because visible intersections lie on the outer skin of the offset model. To obtain the visibility of intersections efficiently, the proposed algorithm uses a graphics board, which performs hidden surface removal on up to a million polygons per second.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.913-918
• /
• 2001

This paper investigates insulating effects and strength properties of concrete under cold climate carrying out the experiment with insulating forms on the slab member. According to test results, under $-10^{\circ}C$ of outer temperature, the surface of concrete exposed to outer temperature goes below zero after 10hours since exposed. And, the surface of concrete covered with vinyl and blanket goes below zero after 42hours. However, the surface of concrete covered with insulating materials such as polystyrene foam does not drop below zero until 55hours. And, according to coring sample strength test, compressive strength cured with insulation shows much higher strength than no insulation curing condition and vinyl and blanket curing condition.

• 한국생산제조학회지
• /
• 제8권6호
• /
• pp.113-118
• /
• 1999

In order to evaluate strength of spot welded joint, at first it is importent that we should know strain distribution near nugget zone. During loading, in HAZ, compressive strain increase with Increase of load, but in nugget zone tensile strain increase. During unloading, on the other hand, even through the decreases, the strain variation is not almost appeared in nugget zone and HAZ. In nugget boundary zone, the strain range increases continuously along with load increase on outer surface, but the strain increases continunously and decreases rapidly beyond yield strength on inner surface. In this paper, strain distribution are measured in inner and outer surface with variation of thickness and load under tensile-shear load. Tensile-shear strength increased as with increase of specimen thickness. As for thickness increase rates are 25%, 50%, 100%, and 150%, tensile-shear strength in crease rates are 40%, 81%, 130% and 228%.

• Journal of Biosystems Engineering
• /
• 제31권5호
• /
• pp.395-402
• /
• 2006

Mixed heat transfer in an indirected NIR (Near Infrared Ray) dry chamber was investigated numerical analysis. It is Important that the miked heat transfer effects on double parameters which the Reynolds number and the position of emit lamp. Reynolds number are based on the outer diameter of the cylinder range from 103 to $30{\times}105$. Four difference heat transfer regimes of behavior are apparent: forced convection and radiation on the outer surface of the cylinder, pure conduction, pure natural convection and radiation between lamp surface and inner surface of the cylinder. The temperature and flow patterns are illustrated by iso-contour lines for the double parameters. Also presented are results on the convective heat transfer flux and the radiative heat transfer flux as increased with Reynolds number.

• 오토저널
• /
• 제15권3호
• /
• pp.96-110
• /
• 1993

A procedure has been developed so that a die-face for stamping automobile outer panels can be design and modelled efficiently. The procedure is composed of four parts each of which corresponds to modeling major components of a die-face, i.e. tipped product, blankholder, draw beads, and step draw. The modeling techniques developed specifically for die-face design enable a designer to generate the shape of a die-face quickly with the minimum input, and the resulting models can be used in FEM analysis and NC tool path generation. This will lead to the reductions in lead time and manhours required for the design and manufacture of the stamping dies.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.411-414
• /
• 2008

In order to study the effect of lubrication during hot rolling, ferritic stainless steel (FSS) sheet were hot-rolled with and without application of lubrication. The effect of two hot rolling processes on the evolution of texture and microstructure after hot rolling, cold rolling and subsequent recrystallization annealing was studied by means of macro-texture analysis and microstructure observations. After hot rolling, the specimen rolled with lubrication showed rolling textures at the sheet surface, while the specimen rolled without lubrication displayed shear textures in the outer layers of the sheet. Hot rolling with lubrication was beneficial to the formation of strong recrystallization textures at sheet surface. However, hot rolling with lubrication led to the formation of orientation colonies in outer thickness layers of the recrystallized sheet.

• 식물분류학회지
• /
• 제49권1호
• /
• pp.90-95
• /
• 2019

Camellia pukhangensis (Theaceae), a new species with yellow flowers from Quy Hop District, Nghe An Province, Vietnam, is described and illustrated. Camellia pukhangensis has nearly sessile leaves with an attenuate to caudate apex, cordate base, hirsute abaxial surface, hirsute adaxial midrib, hirsute petiole, deltate to ovate perules hairy on the outer surface, bright yellow orbicular to obovate petals hairy on the outer surface, androecium pubescent to two-thirds from the base, pubescent ovoid ovary with three (or four) locules and three (or four) pubescent styles free to the base. The morphological data support the provisional placement of C. pukhangensis in Camellia sect. Archecamellia Sealy.