• Restorative Dentistry and Endodontics
• /
• v.43 no.3
• /
• pp.33.1-33.8
• /
• 2018

Objectives: This study aimed to investigate the prevalence of a separate distolingual root and to measure the thickness of the buccal cortical bone in mandibular first molars in Koreans using cone-beam computed tomography (CBCT) images. Materials and Methods: High-quality CBCT data from 432 patients were analyzed in this study. The prevalence of a separate distolingual root of the mandibular first molar was investigated. The distance from the distobuccal and distolingual root apices to the outer surface of the buccal cortical bone was measured. We also evaluated the thickness of the buccal cortical bone. Results: The prevalence of a separate distolingual root (2 separate distal roots with 1 canal in each root; 2R2C) was 23.26%. In mandibular first molars with 2R2C, the distance from the distobuccal root apex to the outer surface of the buccal cortical bone was 5.51 mm. Furthermore, the distance from the distolingual root apex to the outer surface of the buccal cortical bone was 12.09 mm. In mandibular first molars with 2R2C morphology, the thickness of the buccal cortical bone at the distobuccal root apex of the mandibular first molar was 3.30 mm. The buccal cortical bone at the distobuccal root apex was significantly thicker in the right side (3.38 mm) than the left side (3.09 mm) (p < 0.05). Conclusions: A separate distolingual root is not rare in mandibular first molars in the Korean population. Anatomic and morphologic knowledge of the mandibular first molar can be useful in treatment planning, including surgical endodontic treatment.

• Particle and aerosol research
• /
• v.18 no.4
• /
• pp.137-145
• /
• 2022

As many studies on the harmfulness of fine dust have been reported, awareness of its seriousness is spreading. Recently, interest in indoor air quality as well as air pollution is increasing, and research on measures to block fine dust flowing into the room from the outside is being conducted. The clothing company is launching functional clothing to prevent fine dust attached to clothing from entering the room through outdoor activities. However, it is difficult to confirm whether there is actually fine-dust blocking performance, and there is no evaluation standard. In this study, the contamination rate caused by fine dust was quantitatively compared through image processing after contamination of the outer fabric for 4 types of commercially available functional clothing with fine-dust blocking effect. The difference in particle contamination according to the material of the outer fabric was analyzed by comparing the surface resistance, and it was found that the higher the surface resistance of the outer fabric material, the more fine dust was attached. The analysis method of this study is expected to be able to quantitatively compare and evaluate the fine-dust blocking performance of functional clothing.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.2
• /
• pp.112-122
• /
• 1995

While many surfaces such as automobile outer panels, ship hulls and airfoils are characterized by their smooth, free-form shapes, a far larger class of functional surfaces are characterized by highly irregular, multi-featured shapes consisting of pockets, channels, ribs, etc. In constaract to the design of aesthetic, free-form surfaces, functional surface design can perhaps best be viewed as a process of assembling a collection of known component surfaces to form a single compound surface. In this paper, we presents a feature-based functional surface modeling method. A single feature involves a secondary surface, which we must join to a primary surface with a smooth transition between two boundary courves. Through recursive blending of a secondary surface with the primary surface, the mullti-featured surface is represented. After constructing a compound surface, we generate the Z-map for NC machining of the surface. Offsetting the Z-map using the inverse offsetting technique, we get CL tool paths with out gouging.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.322-325
• /
• 2007

Dent resistance is an important characteristic to avoid damage on automotive outer panels. From a practical point of view, dents can be caused in a number of ways. Considering doors as an example, denting can occur from stone impacts or from the careless opening of an adjacently parked vehicle door. Denting can occur where the door surface is smooth and may not have sufficient curvature to resist dent. These exterior body parts are designed to improve dent resistance using a combination of work hardening and bake hardening. In brief, dent is affected by the shape of the parts and the material properties such as yield strength, strain and thickness. In this work, forming of door outer panel is investigated by Taguchi method. Main parameters are yield strength, thickness, blank size, blank holding force and so on. For the given value of design parameters, forming analysis of the thirty six cases are carried out according to L18 orthogonal array. After comparing the performance by simple conversion of simulation results into dent resistance, the final suggestion of the forming parameters is verified for the best improvement of dent resistance.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.4
• /
• pp.455-462
• /
• 2015

A feature line is a visually noticeable creased line on outer automotive panels. Feature lines play an important role in creating a good impression of a car. Even though the manufacturing quality of feature lines is important, it is difficult to achieve the designed shape owing to the springback of sheet metal. The current study presents five methods of making samples that will be used in a visual experiment to discover a quality control quantitative manufacturing allowance for feature lines. Measurement and inspection methods for the samples are also presented. The results show that plunge machining is the most accurate way to make the desired shape, and that wrapping the machined surface with sheet film is an appropriate way to emulate the roughness and visual texture of the painted outer panels of a car.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.5
• /
• pp.109-116
• /
• 2016

Polymethyl methacrylate is commonly used in the outer lens of automotive rear lamps. However, if the lens warps above the allowable limit, it may lead to faulty connection with the housing, and failure of the assembly. This study investigated the effects of gate diameter and cooling line distance in the mold design for automotive outer lens. The optimal gate diameter and cooling line distance to minimize the warp of the outer lens were derived as 3.0 mm and 50-60 mm respectively, and the cooling temperature to minimize warp was shown to be $60-80^{\circ}C$ (mold surface temperature $48-67^{\circ}C$). A higher cooling temperature may somewhat mitigate the warp, but is undesirable because it may cause injection molding problems, such as sinks. A mold was constructed matching the optimal design and the produced lens properties, particularly the degree of warp, were comparable with the CAE predictions.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.5
• /
• pp.487-494
• /
• 2008

An experimental assessment has been made of the drag reducing efficiency of the outer-layer vertical blades, which were first devised by Hutchins (2003). The drag reduction efficiency of the blades was reported to reach as much as 30%. The assessment of the drag reducing efficiency is mainly restricted to the downstream region of the blades. Indeed, sufficient care has not been taken to such adverse effects as the increase in the wetted surface area and the flow disturbances due to the presence of the blades. In the present study, a series of drag force measurements in towing tank and circulating water channel has been performed toward the assessments of the total drag reduction efficiency of the outer-layer vertical blades.

• Transactions of Materials Processing
• /
• v.23 no.4
• /
• pp.211-220
• /
• 2014

The outer race of a constant velocity (CV) joint having six inner ball grooves has traditionally been manufactured by multi-stage warm forging, which includes forward extrusion, upsetting, backward extrusions, necking, ironing and sizing, and machining. In the current study, a multi-stage cold forging process is examined and an assessment for replacing and modifying the conventional multi-stage warm forging is made. The proposed procedure is simplified to the backward extrusion of the conventional process, and the sizing and necking are combined into a single sizing-necking step. Thus, the forging surface of the six ball grooves can be obtained without additional machining. To verify the suitability of the proposed process, a 3-dimensional numerical simulation on each operation was performed. The forging loads were also predicted. In addition, a structural integrity evaluation for the tools was carried out. Based on the results, it is shown that the dimensional requirements of the outer race can be well met.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.1
• /
• pp.100-107
• /
• 1996

In this paper, we report the results of the experimental study on the flow and the mass transport around a square harbor driven by a tidal effect. The model harbor is composed of a uniform water-depth with a straight breakwater. The harbor is connected to the outer ocean by an entrance region having the same shape as the harbor. We investigated two cases, one having another breakwater in the place between the entrance region and the outer ocean, and the other without it, The surface and bottom flow patterns of the model container are visualized by using light particles and dye, respectively. It was shown that the inner harbor and the entrance region have well-organized, large vortical residual flows, and the material transport between the entrance and outer region is however significantly different for two cases; when the breakwater is built between the two regions, the transport is far better than that without it, which is clearly contrary to our common sense that the breakwater would block the dispersion of the materials between the harbor and the outer ocean.

• Transactions of Materials Processing
• /
• v.16 no.4 s.94
• /
• pp.254-259
• /
• 2007

Dent resistance is an important characteristic to avoid damage on automotive outer panels. From a practical point of view, dents can be caused in a number of ways. Considering doors as an example, denting can occur from stone impacts or from the careless opening of an adjacently parked vehicle door. Denting can occur where the door surface is smooth and may not have sufficient curvature to resist dent. These exterior body parts are designed to improve dent resistance using a combination of work hardening and bake hardening. In brief, dent is affected by the shape of the parts and the material properties such as yield strength, strain and thickness. In this work, forming of door outer panel is investigated by Taguchi method. Main parameters are yield strength, thickness, blank size, blank holding force and so on. For the given value of design parameters, forming analysis of the eighteen cases are carried out according to L18 orthogonal array. After comparing the performance by simple conversion of simulation results into dent resistance, the final suggestion of the forming parameters is verified for the optimal improvement of dent resistance.