• 한국해양학회지
• /
• 제27권4호
• /
• pp.303-310
• /
• 1992

산업폐수와 도시하수의 유입이 심한 마산만에서 하계에 각종 질소화합물의 분포와 산소소비율에 대한 연구를 수행하였다. 1986년 하계에 마산만은 육수유입의 영향을 강 하게 받았으며 수온약층 아래에는 빈산소층이 형성되었다. 용존성무기질소(DIN), 용존 성유기질소(DON), 입자성질소(PN) 는 내만 육수유입을 직접받는 곳에서 각각 735.6, 1261.8 amd 48.5 umol/l의 분포를 보였으며 마산내만 입구에서는 각각 79.1, 73.0 and 39.5 umol/l를 나타냈다. 마산내만입구의 일차생산력은 2,695mgC/m$^2$/day였다. 용존산 소량은 내만입구에서는 3 m 아래에서부터, 마산수로에서는 10 m 아래에서부터 1 ml/l 이하를 보였다. 저층수중의 높은 암모니아와 인산염의 농도는 유기물의 활발한 분해나 저층퇴적물로부터의 용출에 의한 것이라 생각된다. ETS 활동도는 마산내민 가장안쪽에 서 212.1ul $O^2$/l/h였고 마산내만입구의 저층수에서는 산소소비가 442 ml $O^2$/day의 비율로 지행되었다. 마산수로저층수에서의 탈질화 속도는 0.25 umol/l/day 였으며 마 산내만입구에서는 표층에서 일차생산에 의해 생성된 유기물의 9.3-10.5%가 저층수에서 분해되는 것으로 보인다.

• Korea-Australia Rheology Journal
• /
• 제19권4호
• /
• pp.183-190
• /
• 2007

Injection molding is one of the most common operations in polymer processing. Good quality products are usually obtained and major post-processing treatment is not required. However, residual stresses which exist in plastic parts affect the final shape and mechanical properties after ejection. Residual stresses are caused by polymer melt flow, pressure distribution, non-uniform temperature field, and density distribution. Residual stresses are predicted in this study by numerical methods using commercially available softwares, $Hypermesh^{TM},\;Moldflow^{TM}\;and\;ABAQUS^{TM}$. Cavity filling, packing, and cooling stages are simulated to predict residual stress field right after ejection by assuming an isotropic elastic solid. Thermo-viscoelastic stress analysis is carried out to predict deformation and residual stress distribution after annealing of the part. Residual stresses are measured by the hole drilling method because the automotive part selected in this study has a complex shape. Residual stress distribution predicted by the thermal stress analysis is compared with the measurement results obtained by the hole drilling method. The molded specimen has residual stress distribution in tension, compression, and tension from the surface to the center of the part. Viscoelastic deformation of the part is predicted during annealing and the deformed geometry is compared with that measured by a three dimensional scanner. The viscoelastic stress analysis with a thermal cycle will enable us to predict long term behavior of the injection molded polymeric parts.

• Journal of Microbiology and Biotechnology
• /
• 제13권3호
• /
• pp.437-443
• /
• 2003

Bioremediation technologies were applied to experimental microcosms, simulating an oil spill in a lower intertidal area. Three treatments (oil only, oil plus nutrients, and oil plus nutrients and microbial inocula) were applied, and each microcosm was repeatedly filled and eluted with seawater every 12 h to simulate tidal cycles. To minimize washing-out of the inoculum by the tidal cycles, microbial cells were primarily immobilized on diatomaceous earth before they were applied to the oiled sand. Oil degradation was monitored by gravimetric measurements, thin layer chromatography/flame ionization detector (TLC/FID) analysis, and gas chromatography (GC) analysis, and the loss of oil content was normalized to sand mass or nor-hopane. When the data were normalized to sand mass, no consistent differences were detected between nutrient-amended and nutrient/inoculum-amended microcosms, although both differed from the oil-only microcosm in respect of oil removal rate by a factor of 4 to 14. However, the data relative to nor-hopane showed a significant treatment difference between the nutrient-amended and nutrient/inoculum-treated microcosms, especially in the early phase of the treatment. The accelerating effect of inoculum treatment has hardly been reported in studies of oil bioremediation in the Tower intertidal area. The inoculum immobilized on diatomaceous earth seemed to be a very effective formulation for retaining microbial cells in association with the sand. Results of this study also suggest that interpretation of the effectiveness of bioremediation could be dependent on the selection of monitoring methods, and consequently the application of various analytical methods in combination could be a solution to overcome the limitations of oil bioremediation monitoring.

• 한국환경보건학회지
• /
• 제36권4호
• /
• pp.337-341
• /
• 2010

The modified simultaneous differential staining technique, which enables double staining of cartilage and bones, needs to be improved to prevent soft tissues from being damaged during the staining process. Key factors influencing the extent to which soft tissues are damaged include the fixative used, macerating time, potassium hydroxide concentration, incubation temperature and the removal of skin from specimens. Here we describe a protocol that enables the hardening of tissues during bleaching and maceration. We also describe a method for objectively measuring rates of cartilage and bone growth. The use of formalin as a fixative rendered soft tissues more rigid due to the resulting chemical bonds formed between proteins. Blotted specimens were immersed in 1% potassium hydroxide (KOH) and incubated at $37^{\circ}C$ for 1 day (smaller specimens) or 2-3 days (larger specimens). The 1% KOH solution was also used as the diluent solution for the subsequent immersion in a graded series of 30%, 50%, 70%, 90%, 100% glycerol solutions, a procedure that made soft tissues even more transparent and hardened. It was not necessary to remove the skin of specimens shorter than 2 cm, since the macerating solution could easily penetrate their thin skin layer and continuously remove those pigments hindering visibility. Since excessive osmosis is another factor that can damage soft tissues in the macerating process by causing the rupture of those cells not able to withstand the osmotic pressure, here it was minimized by balancing the salt concentration between the interior and exterior of cells with the addition of 0.9% sodium chloride (NaCl) in the macerating solution. Finally, to determine the proportions of cartilage and bone growth, photographs of the stained specimens were taken with a dissecting microscope and sections corresponding to the cartilage and bones were cut out from the printed pictures and weighed. Our results show that this method is suitable for the objective evaluation of bone and cartilage growth.

• The Journal of Advanced Prosthodontics
• /
• 제6권4호
• /
• pp.295-301
• /
• 2014

PURPOSE. Numerous methods were used to etch the fiber posts to improve its bonding to root canal dentin. Our aim was to evaluate the efficacy of 37% phosphoric acid in etching fiber posts in comparison with 24% hydrogen peroxide. MATERIALS AND METHODS. Ninety human maxillary central incisors were taken and post space preparation was done. Ninety fiber posts were taken and divided into three groups (n=30) based on the surface treatment they received ($H_3PO_4$, $H_2O_2$, distilled water) and each group was further divided (n=10) based on the time period of application (15 seconds, 30 seconds, 60 seconds). All the posts were luted into canals using Rely X UniCem-2. Each tooth was then sectioned into six slices and subjected to push out test. Data obtained was subjected to statistical analysis at P<.05. The surface topography was evaluated using scanning electron microscopy. RESULTS. Highest bond strength values were noted in 15 seconds etched phosphoric acid group and 60 seconds etched hydrogen peroxide group with no significant difference between two groups. Surface topography revealed complete epoxy layer removal with no damage to its structural integrity in those groups. CONCLUSION. $H_3PO_4$ etching for a period of 15 seconds is an effective alternative in improving the adhesion of fiber post to root dentin.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 추계학술발표대회 논문집
• /
• pp.245-248
• /
• 2011

Many researches have been carried out to improve light absorption in the crystalline silicon solar cell fabrication. The rear reflection is applied to increase the path length of light, resulting in the light absorption enhancement and thus the efficiency improvement mainly due to increase in short circuit current. In this paper, we manufactured the silicon solar cell using the mono crystalline silicon wafers with $156{\times}156mm^2$, 0.5~3.0 ${\Omega}{\cdot}cm$ of resistivity and p-type. After saw damage removal, the dielectric film ($SiN_x$)on the back surface was deposited, followed by surface texturing in the KOH solution. It resulted in single-side texturing wafer. Then the dielectric film was removed in the HF solution. The silicon wafers were doped with phosphorus by $POCl_3$ with the sheet resistance 50 ${\Omega}/{\Box}$ and then the silicon nitride was deposited on the front surface by the PECVD with 80nm thickness. The electrodes were formed by screen-printing with Ag and Al paste for front and back surface, respectively. The reflectance and transmittance for the single-sided and double-sided textured wafers were compared. The double-sided textured wafer showed higher reflectance and lower transmittance at the long wavelength region, compared to single-sided. The completed crystalline silicon solar cells with different back surface texture showed the conversion efficiency of 17.4% for the single sided and 17.3% for the double sided. The efficiency improvement with single-sided textured solar cell resulted from reflectance increase on back surface and light absorption enhancement.

• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• 제1권1호
• /
• pp.19-33
• /
• 1997

The high oxidants, which occur the daily maximum concentrations in the afternoon, are transported into the other region via long range transport mechanisms or trapped within the shallow mixing boundary layer and then removed physically (deposition, transport by mountain wind, etc.) and chemically (reaction with local sources). Therefore, modeling formation of photochemical oxidants requires a complex description of both chemical and meteorological processes. In this study, as a part of air quality studies, we reviewed various aspects of photochemical modeling on the basis of currently available literature. The result of the review shows that the model is based on a set of coupled continuity equations describing advection, diffusion, transport, deposition, chemistry, emission. Also photochemical oxidant models require a large amount of input data concerned with all aspects of the ozone life cycle. First, emission inventories of hydrocarbon and nitrogen oxides, with appropriate spatial and temporal resolution. Second, chemical and photochemical data allowing the quantitative description of the formation of ozone and other photochemically-generated secondary pollutants. Third, dry deposition mechanisms particularly for ozone, PAN and hydrogen peroxide to account for their removal by absorption on the ground, crops, natural vegetation, man-made and water surfaces. Finally, meteorological data describing the transport of primary pollutants away from their sources and of secondary pollutants towards the sensitive receptors where environmental damage may occur. In order to improve our present study, shortcomings and limitation of existing models are pointed out and verification process through observation is emphasized.

• Korean Chemical Engineering Research
• /
• 제46권5호
• /
• pp.965-970
• /
• 2008

접촉분해경유의 산화반응후 포함된 산화황화합물을 분리하기위해 다양한 용매를 사용하여 용매추출에 관한 연구를 수행하였다. 용매로는 극성을 가진 물, N-메틸피놀리논, 에틸아세테이트, 디메틸포름아마이드, 이소프로필알코올, 아세토니트릴, 메탄올등을 사용하였다. 실험결과, 접촉분해경유와 용매와의 층분리는 적절한 양의 물을 첨가한 경우에 이루어졌으며, 물과 N-메틸피놀리논을 혼합한 혼합용매가 접촉분해경유로부터 산화황화합물의 선택적인 분리에 가장 적절하였다. 또한 접촉분해경유로부터 황화합물을 99.5% 이상으로 제거하기 위해선, 4단 정도의 평형추출이 필요하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1992년도 춘계학술대회 논문집
• /
• pp.110-113
• /
• 1992

$n^{+}$-p homojunction InP diodes were fabricated using thermal diffusion of Sulfur into p-type InP substrates(Zn doped, LEC grown, p=2.3${\times}$10$^{16}$c $m^{-3}$). The Sulfur diffusion was carried out at 550$^{\circ}C$, 600$^{\circ}C$, 700$^{\circ}C$ for 4 hours in a sealed quartz ampule(～2ml in volume) containing 5mg I $n_2$ $S_3$ and Img of red phosphorus. The formed junction depth was below 0.5$\mu\textrm{m}$. After the removal of diffused layer on the rear surface of the wafer, the beak ohmic contacts to the p-side were made with a vacuum evaporation of An-Zn(2%) followed by an annealing at 450$^{\circ}C$ for 5 minutes in flowing Ar gas. The front contacts were made with a vacuum evaporation of Au-Ge(12%) followed by an annealing at 500$^{\circ}C$ for 3 minutes in flowing Ar gas. The remarkable sprctral response of the cells obtained at the region of 6000-8000${\AA}$ region. The open circuit voltage $V_{oc}$ , short circuit current density $J_{sc}$ , fill factor and conversion efficiency η of the fabricated pattern solar cells(diffusion condition : at 700$^{\circ}C$ for 4 hours) were 0.660V, 14.04㎃/$\textrm{cm}^2$, 0.6536 and 10.09%, respectively.y.

• Archives of Plastic Surgery
• /
• 제38권5호
• /
• pp.715-717
• /
• 2011

Purpose: In cases of breast reconstruction with a free transverse rectus abdominis musculocutaneous (TRAM) flap after skin-sparing mastectomy with nipple-areolar complex (NAC) removal, the flat contour of the flap's skin paddle can easily look unnatural and dissatisfying. Reconstructed NAC on the flap surface lacks the elevated contour that the normal areola possesses, resulting in an unnatural final result. Therefore, we would like to introduce a novel method to improve this problem and report the satisfactory results we obtained. Methods: Operations were conducted on 19 patients who underwent immediate breast reconstruction with a free TRAM flap and skin-sparing mastectomy from January 2009 to January 2010, with a mean follow-up of nine months. While the TRAM free flap was being inset, a purse-string suture was carried out on the dermal layer of skin flap to create a slight protrusion with Gore-$Tex^{(R)}$ sutures. Results: The elevated mound surrounding the NAC was well maintained for an average follow-up period of nine months. Nipple projection was also well maintained. There was no complaint about breast contour or nipple height reduction. In addition, there was no reported incidence of other complications. Conclusion: The purse-string suture technique presents a more natural breast silhouette around the NAC and helps to maintain nipple projection. Furthermore, it does not require any supplementary incisions or complicated skills. There has been no report of additional complications using this technique.