• KSBB Journal
• /
• v.28 no.3
• /
• pp.208-212
• /
• 2013

Four types of mesoporous spherical silica adsorbents with different physical properties were prepared by spray pyrolysis and were used for the purification of the anticancer agent paclitaxel from plant cell cultures. Pore size had a greater effect on the removal of plant-derived impurities during the pre-purification of paclitaxel compared with surface area and pore volume. An appropriate pore diameter (~9.07 nm) was required to achieve the highest purity (~46.1%) and yield (~82.3%) of paclitaxel. These results were confirmed by HPLC analysis of the absorbent after treatment and Thermogravimetric analysis of the organic substances bonded to the adsorbent.

• Tribology and Lubricants
• /
• v.33 no.6
• /
• pp.282-287
• /
• 2017

SU-8 is an epoxy-type photoresist widely used for the fabrication of high-aspect-ratio (HAR) micro-structures in micro-electro-mechanical systems (MEMS). To fabricate highly integrated structures, chemical mechanical polishing (CMP) has emerged as the preferred manufacturing process for planarizing the MEMS structure. In SU-8 CMP, an oxidizer decomposes organic impurities and particles in the CMP slurry remove the chemically reacted surface of SU-8. To fabricate HAR microstructures using the CMP process, the adhesion between SU-8 and substrate material is important to avoid the delamination of the SU-8 film caused by the mechanical-dominant material removal characteristic. In this study, the friction force during the CMP process is measured with a CMP monitoring system to detect the delamination phenomenon and investigate the delamination of the SU-8 film from the silicon substrate under various pressure conditions. The increase in applied pressure causes an increase in the frictional force and wafer-edge stress concentration. The frictional force measurement shows that the friction force changes according to the delamination phenomenon of the SU-8 film, and that it is possible to monitor the delamination phenomenon during the SU-8 CMP process. The delamination at a high applied pressure is explained by the effect of stress distribution and pad deformation. Consequently, it is necessary to control the pressure of polishing, which can avoid the delamination in SU-8 CMP.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.4
• /
• pp.853-856
• /
• 2009

Highly polycrystalline copper indium diselenide (CuInSe2, CIS) thin films were deposited on glass or ITO glass substrates by two-stage metal organic chemical vapor deposition (MOCVD) at relatively mild conditions, using Cuand In/Se-containing precursors. First, pure Cu thin film was prepared on glass or ITO glass substrates by using a single-source precursor, bis(ethylbutyrylacetate)copper(II) or bis(ethylisobutyrylacetato)copper(II). Second, on the resulting Cu films, tris(N,N-ethylbutyldiselenocarbamato)indium(III) was treated to produce CuInSe2 films by MOCVD method at 400 ${^{\circ}C}$. These precursors are very stable in ambient conditions. In our process, it was quite easy to obtain high quality CIS thin films with less impurities and uniform thickness. Also, it was found that it is easy to control the stoichiometric ratio of relevant elements on demands, leading to Cu or In rich CIS thin films. These CIS films were analyzed by XRD, SEM, EDX, and Near-IR spectroscopy. The optical band gap of the stoichiometric CIS films was about 1.06 eV, which is within an optimal range for harvesting solar radiation energy.

• Journal of Hydrogen and New Energy
• /
• v.27 no.2
• /
• pp.135-143
• /
• 2016

Biogas is a renewable fuel from anaerobic digestion of organic matters such as sewage sludge, manure and food waste. Raw biogas consists mainly of methane, carbon dioxide, hydrogen sulfide, and water. Biogas may also contain other impurities such as siloxanes, halogenated hydrocarbons, aromatic hydrocarbons. Efficient power technologies such as fuel cell demand ultra-low concentration of containments in the biogas feed, imposing stringent requirements on fuel purification technology. Biogas is upgraded from pressure swing adsorption after biogas purification process which consists of water, $H_2S$ and siloxane removal. A polymer electrolyte membrane fuel cell power plant is designed to operate on reformate produced from upgraded biogas by steam reformer.

• Journal of Power System Engineering
• /
• v.18 no.6
• /
• pp.133-139
• /
• 2014

In this research, the photocatalytic degradation of benzothiophene in $TiO_2$ aqueous suspension has been studied. $TiO_2$ photocatalysts are prepared by a sol-gel method. The dominant anatase-structure on $TiO_2$ particles is observed after calcining the $TiO_2$ gel at $500^{\circ}C$ for 1hr. Photocatalysts with various transition metals (Nd, Pd and Pt) loading are tested to evaluate the effect of transition metal impurities on photodegradation. The photocatalytic degradation in most cases follows first-order kinetics. The maximum photodegradation efficiency is obtained with $TiO_2$ dosage of 0.4g/L. The photodegradation efficiency with Pt-$TiO_2$ is higher than pure $TiO_2$ powder. The optimal content value of Pt is 0.5wt.%. Also we investigate the applicability of $H_2O_2$ to increase the efficiency of the $TiO_2$ photocatalytic degradation of benzothiophene. The optimal concentration of $H_2O_2$ is 0.05. The effect of pH is investigated; we obtain the maximum photodegradation efficiency at pH 9. Hydroxy-benzothiophenes and dihydroxy-benzothiophenes are identified as reaction intermediates. It is proposed that benzothiophene is oxidized by OH radical to sequentially form hydroxyl-benzothiophenes, dihydroxybenzothiophenes, and benzothiophenedione.

• Resources Recycling
• /
• v.20 no.2
• /
• pp.60-66
• /
• 2011

Solvent extraction experiments were carried out to recover and separate Ru(III) from aqueous hydrochloric acid media using TBP and Cyanex923. The efficiency of the extraction was studied under various experimental conditions, such as concentration of HCl and NaCl, concentration of extractant in the organic phase and temperature. The extraction behavior of metal impurities, such as Pt, Bi, Sn, Fe, Pb and Cu in mixed solutions was examined. From the experimental studies, it was found that the Cyanex923 resulted in higher extraction percentage of Ru than TBP. However TBP was more effective for the separation of Ru and Pt, Bi, Sn in mixed solutions than Cyanex923.

• Journal of Conservation Science
• /
• v.37 no.4
• /
• pp.340-356
• /
• 2021

We have tried the experimental research of lost-wax casting to reconstruct Gilt-Bronze Pensive Bodhisattva; preliminary and reconstruction experiment based on ancient texts. Main object to reconstruct is Korean National Treasure No.83, Gilt-Bronze Pensive Bodhisattva (Maitreya), then we measure alloy ratio and casting method based on the scientific analysis. Other impurities were removed from the base metal components(copper : tin : lead) and their ratio was set to 95.5 : 6.5 : 3 where the ratios for tin and lead were increased by 2.5% each. The piece-mold casting method was used, and piece-mold casting experiments were carried out twice in this study but supplementary research on piece-mold casting was necessary. The microstructure was confirmed to be typical cast microstructure and the component analysis result was similar to that of the prior study. Analysis of the chemical composition is confirmed to copper, tin, lead, and zinc, and the chemical composition of the matrix was 87.8%Cu-7.5%Sn-2.7%Pb-2.1%Zn, and similar to previous experimental research. Also resulted in the detection of small impurity in Zn. Analysis of the mould revealed that the mould was fabricated by adding quartz and organic matter for structural stability, fire resistance, and air permeability. We expect that our research will contribute to provide base data for advanced researches in future.

• Resources Recycling
• /
• v.15 no.5 s.73
• /
• pp.3-10
• /
• 2006

The solvent extraction for the separation of platinum group metals from the leach liquor of spent automotive catalysts has been studied. Tri-n-butyl phosphate (TBP), tri-n-octylamine (TOA) and di-n-hexyl sulfide (DHS) were used as extractants and kerosene as a diluent. The extraction behavior of platinum, palladium and rhodium has been investigated as functions of different kinds of extractants and their concentrations. In addition, the extraction behavior of the major metal impurities such as cerium, lead, iron, magnesium and aluminum has been investigated. Platinum and palladium were extracted with TBP. And platinum, palladium and rhodium were extracted with TOA. Platinum was co-extracted with palladium into the organic phase by solvent extraction using SFI-6 of DHS extractant, but only palladium was selectively extracted with SFI-6R. The selective extraction of palladium with SFI-6R was found better than that with SFI-6, but the kinetics of extraction with SFI-6R was found poor in comparison to SFI-6. The metal impurities extracted simultaneously during the extraction of platinum group metals should be removed in scrubbing and stripping processes. A suitable process has been proposed for the separation of platinum group metals from the leach liquor of spent automotive catalysts. Initially palladium was extracted with SFI-6R, followed by the separation of platinum with TBP or TOA leaving rhodium in the raffinate.

• Korean Journal of Materials Research
• /
• v.5 no.7
• /
• pp.775-780
• /
• 1995

Thin films of titanium nitride are formed using the tetrakis-dimethyl-amino-titanium (TDMAT(Ti[N($CH_3$)$_2$]$_4$)) under various conditions. The formation of TiN films has been obtained from the thermal decomposition of the Ti-precursor and the gas phase reaction between TDMAT and ammonia(NH$_3$). The resistivity of the MOCVD film can be attributed to their impurity. Especially the curve fitting graph of XPS data is revealed that main impurities in the films as carbon and oxygen make various interstitial compounds which has influenced physical and electrical properties of the film. In the contact hole with the aspect ratio of 3:1 and the diameter of 0.5${\mu}{\textrm}{m}$, the SEM morphology shows that the step coverage is more decreased in the films formed y flowing ammonia additionally than the films formed by pyrolysis of TDMAT and the phenomenon is probably related with the activation energy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.355-355
• /
• 2016

There has been an explosive development of nanocrystal (NC) synthesis and application due to their composition-dependent specific properties. Despite the composition, shape, and size of NCs foremost determine their physicochemical properties, the surface state and molecule conjugation also drastically change their characteristics. To make practical use of NCs, it is a prerequisite to understand the NC surface state and the degree to which they have been modified because the reaction occurs on the interface between the NCs and the surrounding medium. We report in here an analysis method to identify conjugated ligands and their binding states on semiconductor nanocrystals based on their molecular information. Surface science techniques, such as time-of-flight secondary-ion mass spectrometry (ToF-SIMS) and FT-IR spectroscopy, are adopted based on the micro-aggregated sampling method. Typical trioctylphosphine oxide-based synthesis methods of CdSe/ZnS quantum dots (QDs) have been criticized because of the peculiar effects of impurities on the synthesis processes. Since the ToF-SIMS technique provides molecular composition evidence on the existence of certain ligands, we were able to clearly identify the n-octylphosphonic acid (OPA) as a surface ligand on CdSe/ZnS QDs. Furthermore, the complementary use of the ToF-SIMS technique with the FT-IR technique could reveals the OPA ligands' binding state as bidentate complexes.