• Microbiology and Biotechnology Letters
• /
• v.41 no.2
• /
• pp.176-182
• /
• 2013

Several types of mesoporous alumina adsorbents with different physical properties were prepared by spray pyrolysis and were used for the separation/purification of the anticancer agent paclitaxel. The pore diameter of the adsorbents had a greater effect than did the surface area and the pore volume on the removal of plant-derived impurities. An appropriate pore diameter (~10.8 nm) was required for effective impurity removal. At a constant pore diameter, the surface area of the adsorbent affected not only the purity but also the yield of paclitaxel. Also, increasing the surface area of the adsorbent resulted in an increase in the adsorption of paclitaxel and impurities (biomass-derived tar and wax components). Removal of these impurities was confirmed by HPLC analysis of the absorbent after the treatment and TGA of the organic substances that were bound to the adsorbent.

• Analytical Science and Technology
• /
• v.30 no.5
• /
• pp.226-233
• /
• 2017

In general, quantitative chemical analysis in various areas including food, the environment, in vitro diagnostics, etc., requires traceability in order to increase the reliability of the measurements. Measurement traceability is a property of an unbroken chain of comparisons relating an instrument's measurements to SI units. Purity analysis is the first process for establishing traceability to SI units in chemical measurements. The purpose of this study is to develop and validate a method of purity assignment for establishing the traceability of $17{\beta}$-estradiol measurements in an in vitro diagnostics field. The establishment of this method is very important as it can be applied to the development of CRM and to the analysis of the purity of other hormones. The method of assignment of the purity of $17{\beta}$-estradiol was developed using the mass balance method and was validated through participation in an International comparison. In the mass balance method, impurities are categorized into four classes as follows: total related structure impurities, water, residual organic solvents, and nonvolatiles/inorganics. In this study, total related structure impurities were characterized by a gas chromatography-flame ionization detector (GC-FID) and a high-performance liquid chromatography-ultraviolet (HPLC-UV) detector, water content was determined by a Karl-Fisher coulometer, and total residual solvents and nonvolatiles/inorganics were checked simultaneously by thermogravimetric analysis (TGA). The purity of the $17{\beta}$-estradiol was 985.6 mg/g and the expanded uncertainty was 2.1 mg/g at 95% confidence. The developed method can be applied to the development of certified reference materials, which play a critical role in traceability.

• Korean Journal of Soil Science and Fertilizer
• /
• v.50 no.5
• /
• pp.462-471
• /
• 2017

A more efficient use of nutrients from organic sources can benefit both farmers and water quality in agriculture. In this paper we reviewed information related to the regulations and guidelines of a swine liquid fertilizer to propose an establishment scheme for the official standards of swine manure slurry as a liquid fertilizer for organic farming. According to the law of establishment and designation of official standard of fertilizers, the liquid fertilizer made with pig liquid manure belongs to the byproduct fertilizer as of one of organic fertilizer. However, the official standards for byproduct fertilizers including the liquid fertilizer set by the Rural Development Administration (RDA), especially for a liquid swine manure fertilizer, should be revised to meet the goals of laws pursuing the environmentally sound agriculture, especially for organic farming because the terms and relevant standards need additional specific standards alike the standards such as impurities and parameter for declaration in EU. Therefore, it is suggested that official standards for byproduct fertilizers should be revised with respect to nutrient, salt content as of SAR and Na content instead of NaCl. Also we need to develop the maximum limit of heavy metals in soil to which the liquid fertilizer can be applied, as well as application rate depending on EC of the liquid fertilizer.

• 보존과학연구
• /
• s.29
• /
• pp.199-220
• /
• 2008

Hobun(Oyster shell White) is a traditional material used as extender and white pigment from ancient times. The production method of it, however, has been discontinued. We have studied the traditional production method of Hobun by weathering oyster shell, which is one of the traditional ways for preparing Hobun. Reproduction study of manufacturing method of the discontinued traditional material is an important accomplishment of our research. Also this study provides solid background knowledge to stabilize the production and supply of Hobun for the cultural asset repairing materials. The result can be summarized as follows: The production process of Hobun by weathering method takes 5 steps - (1) weathering shells ${\rightarrow}$ (2) washing ${\rightarrow}$ (3) pulverization ${\rightarrow}$ (4) separating fine powder by submerging in water ${\rightarrow}$ (5) drying. The major aim in step (1) is to eliminate organic impurities. In the step (4), the fine particles smaller than $25{\mu}m$ are separated by extracting the supernatant from stirred suspension after heavy particles are submerged. Also, the soluble inorganic impurities can be eliminated through the powder submerge in 15 times water and stirring the suspension 6 hours and changing the water 3~4 times. The final products have high quality with 94.03, 0.52, 2.05 for L, a, b, less than $25{\mu}m$ particle size, fine resistance for discoloration by light and environmental pollution and good workability.

• Textile Coloration and Finishing
• /
• v.28 no.4
• /
• pp.239-245
• /
• 2016

In this study, carbon/phenol composites were prepared from carbon fiber preform and phenol resin by RTM(resin transfer molding) process. And changes in the properties of the composite according to the pre-treatment of phenol resin was mainly studied. RTM process conditions were deduced from viscosity and thermal analysis of phenol resin which were rheometer and thermogravimetric analyzer(TGA). RTM process was performed under various injection and molding temperature. Characterization of the prepared C/P composites were evaluated by various analysis. Morphology of composites was analyzed by Micro-CT(MCT), Mechanical properties of composites were measured through the flexural properties. As results, volatile impurities of phenol resin were effectively removed at resin pre-treatment temperature of $100^{\circ}C$ and composite was sufficiently cured at molding temperature of $180^{\circ}C$.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.6 no.2
• /
• pp.209-221
• /
• 1996

The purpose of this study was to find a suitable cosolvent to $CS_2$ so that desorption efficiency can be improved for both polar and non-polar organic solvent mixtures collected on an activated charcoal tube. Cosolvents added to $CS_2$ include: DMF(N,N-dimethylformamide): $CS_2$ (v/v 1:99), DMF:$CS_2$(v/v 3:97), BC (butyl carbitol, 2-(2-butoxy ethoxy) ethanol):$CS_2$(v/v 1:99), and BC:$CS_2$(v/v 3:97)). The results obtained were as follows : 1. Comparing the desorption efficiency of $CS_2$ with those of $CS_2$ with 1, 3, 5 % DMF and 1, 3 % BC cosolvents for two different groups of charcoal tubes each containing 8 different polar and non-polar organic solvents with 3 different concentration levels, the desorption efficiencies of the cosolvent-added $CS_2$ increased significantly for all polar organic solvents regardless of concentration levels tested. For non-polar organic solvents, no noticeable improvement was detected except xylene and trichloroethylene. The desorption efficiency of xylene increased significantly while that of trichloroethylene increased significantly at the lowest concentration level tested. 2. Either 5 % DMF or 3 % BC was the most suitable cosolvent because the desorption efficiency for non-polar organic solvent mixtures was similar or slightly improved compared with that of $CS_2$, while those of for polar organic solvent mixtures were above 75 % except for cyclohexanone. 3. The smallest variations in desorption efficiency represented by the ratio calculated from the maximum to minimum desorption efficiency for all concentration levels tested were found when 3 % BC was used as a cosolvent. The above results indicate that the desorption efficiency of $CS_2$ particularly for polar organic solvent mixtures collected on a charcoal tube can be significantly improved by the use of cosolvents such as 5 % DMF or 3 % BC. A caution, however, is in order for selecting a cosolvent whenever the cosolvent itself is being used in the workplace or the impurities contained in the cosolvent may interfere with the analytical results. In addition, to improve desorption efficiencies for such organic solvents as cyclohexanone or ketones, it is recommended to use suitable collection and desorption media other than the traditional method of charcoal tube collection/$CS_2$ desorption.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.9 no.1
• /
• pp.156-172
• /
• 1999

Potential chemical hazards encountered in painting operation of four shipyards and a ship-repair shop were investigated through the material safety data sheets (MSDS). Material safety data sheets (MSDS) for 307 paints, 50 thinners and 34 binders were collected and reviewed. It was shown that various organic solvents such as aromatic hydrocarbons, aliphatic hydrocarbons, ketones, alcohols, glycols, glycol ether acetates and esters were contained in painting materials. Of these solvents, xylene was found in the largest number of painting materials. sixty percent of the thinners contained xylene in the contents of 20-100%. Other most frequently found solvents were 1-methoxypropanol, 1-methoxypropyl acetate, n-butanol, methyl isobutyl ketone, toluene, isopropanol, and n-butyl acetate, etc. Glycol ethers such as 2-methoxyethanol (2-ME), 2-methoxyethyl acetate (2-MEA), 2-ethoxyethanol (2-EE), 2-ethoxyethyl acetate (2-EEA) and 2-butoxyethanol (2-BA) were regarded as having the potential to cause adverse reproductive effects, embryotoxic effect and hematotoxic effects, and were found in some epoxy panting materials. Coal tar pitch was included in some paints(13%) where polynuclear aromatic hydrocarbons (PAHs) could be contaminated. Inorganic pigments such as lead chromate and zinc potassium chromate were found in some paints (8%). The epoxy resin based paints, which may contain isocyanates such as toluene diisocyanates and hexamethylene diisocyanates causing potential sensitization and asthma to upper respiratory organ, were mostly used in the shipyards. The constituents in the MSDS were significantly different from the results analyzed using gas chromatography/mass detector: minor constituents or impurities were omitted in many MSDS. In conclusion, xylene was the most frequent organic solvent in painting materials, and glycol ethers, including 2-ME, 2-MEA, 2-EE, 2-EEA and 2-BA, were found some products. Also, painting workers may be exposed to PAHs, lead, chromate, isocyanates, organic tin and other various chemicals. The compositions of chemicals in painting materials were variable significantly, and the hazards were changed. These facts should be considered in environmental monitoring and control of the hazards.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.7
• /
• pp.953-956
• /
• 2003

Hexagonal GaN (h-GaN) films have been grown on Si(111) substrates by metal organic chemical vapor deposition using the azidodiethylgallium methylamine adduct, Et₂Ga(N₃)·NH₂Me, as a new single precursor. Deposition was carried out in the substrate temperature range 385-650 °C. The GaN films obtained were stoichiometric and did not contain any appreciable amounts of carbon impurities. It was also found that the GaN films deposited on Si(111) had the [0001] preferred orientation. The photoluminescence spectrum of a GaN film showed a band edge emission peak characteristic of h-GaN at 378 nm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.3
• /
• pp.180-184
• /
• 2017

In this study, we examine the electrical properties of diketopyrrolopyrrole (DPP) containing polymer semiconductors that have been reported to show high performance with ambipolar characteristics. We prepared three different DPP based polymer semiconductors (PDPPTPT, PDPP3T, and PDPP2T-TT) and fabricated organic thin film transistors (OTFTs) with ambipolar polymer semiconductors as an active layer. All three DPP polymers showed only p-type properties at initial measurements. However, after annealing in vacuum oven for 24 hours, it was found that the DPP based polymers have both p-type and n-type properties. It is speculated that the residual impurities supposedly regarded as a strong electron trap source were eliminated during the vacuum process.

• Journal of the Korean Society of Combustion
• /
• v.12 no.4
• /
• pp.47-56
• /
• 2007

Utilization of sewage sludge for industrial fuel should be considered in appropriate calory with low emission of environmental pollutants and the amount of sewage sludge for continuously long-time operation. For the low grade fuel(<4,000kcal/kg), one of proper processes is that coal and oil are added into sewage sludge to remove impurities and increase calory(>7,000kcal/kg) and the amount of fuel having sewage sludge. Recently, 2-step agglomeration has been attempted by secondarily agglomerate sewage sludge onto the primary nuclei formed by agglomeration of coal and oil. Furthermore, sawdust and waste oil can substitute about 1/3 each for coal and mineral oil consumed in this process, which will lead to securing alternative energy resources from environmental pollutants as well as cost reduction.