• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1274-1274
• /
• 2008

In this report, the effect of substrate temperature on the electrical properties of ink-jet printed triisopropylsilyl (TIPS) pentacene organic thin-film transistors (OTFTs) has been investigated. The electrical properties such as mobility and on/off ratio were decreased as the substrate was heated above room temperature. The field-effect mobility of decreased from $10^{-2}cm^2/Vs$ to $10^{-5}cm^2/Vs$ and the on/off ratio decreased from $10^6$ to $10^4$ when the substrate temperature was heated from room temperature to 60$^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.176-176
• /
• 2010

One of the critical issues for applications of flexible organic thin film transistors (OTFTs) for flexible electronic systems is the electrical stabilities of the OTFT devices, including variation of the current on/off ratio (Ion/Ioff), leakage current, threshold voltage, and hysteresis under repetitive mechanical deformation. In particular, repetitive mechanical deformation accelerates the degradation of device performance at the ambient environment. In this work, electrical stability of the pentacene organic thin film transistors (OTFTs) employing multi-stack hybrid encapsulation layers was investigated under mechanical cyclic bending. Flexible bottom-gated pentacene-based OTFTs fabricated on flexible polyimide substrate with poly-4-vinyl phenol (PVP) dielectric as a gate dielectric were encapsulated by the plasma-deposited organic layer and atomic-layer-deposited inorganic layer. For cyclic bending experiment of flexible OTFTs, the devices were cyclically bent up to 105 times with 5mm bending radius. In the most of the devices after 105 times of bending cycles, the off-current of the OTFT with no encapsulation layers was quickly increased due to increases in the conductivity of the pentacene caused by doping effects from $O_2$ and $H_2O$ in the atmosphere, which leads to decrease in the Ion/Ioff and increase in the hysteresis. With encapsulation layers, however, the electrical stabilities of the OTFTs were improved significantly. In particular, the OTFTs with multi-stack hybrid encapsulation layer showed the best electrical stabilities up to the bending cycles of $10^5$ times compared to the devices with single organic encapsulation layer. Changes in electrical properties of cyclically bent OTFTs with encapsulation layers will be discussed in detail.

• Journal of the Korean Vacuum Society
• /
• v.17 no.3
• /
• pp.195-198
• /
• 2008

In this paper, it was demonstrated that organic thin-film transistors (OTFTs) were fabricated with the organic passivation layer by vapor deposition polymerization (VDP) processing. In order to form polymeric film as a passivation layer, VDP process was also introduced instead of spin-coating process, where polymeric film was co-deposited by high-vacuum thermal evaporation from 6FDA and ODA followed by curing. In order to investigate by compared with different passivation layer, the other OTFTs is fabricated to passivation by Polyvinylalcohol using spincoating. We can see that two different ways of passivation layer affect electric characteristic of OTFTs. The initial electric characteristic of OTFTs before passivation such as field effect mobility, threshold voltage, and on-off current ratio are $0.24cm^2/Vs$, -3V, and $10^6$, respectively. Then after polyimide passivation layer, field effect mobility change from $0.24cm^2/Vs$ to $0.26cm^2/Vs$, threshold voltage from -3V to 1V and on-off current ratio from $10^6$ to $10^6$, respectively. In the case of polyvinylalcohol passivation, the initial electric characteristic of OTFTs before passivation such as field effect mobility, threshold voltage, and on-off current ratio are $0.13cm^2/Vs$, 0V, and $10^6$, respectively. Then after polyvinylalcohol passivation layer, field effect mobility changes from $0.13cm^2/Vs$ to $0.13cm^2/Vs$, threshold voltage from 0V to 2V, and on-off current ratio from $10^6$ to $10^5$, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.137-137
• /
• 2009

Thin-film transistors (TFTs) that can be prepared at low temperatures have attracted much attention due to the great potential for flexible electronics. One of the mainstreams in this field is the use of organic semiconductors such as pentacene. But device performance of the organic TFTs is still limited by low field effect mobility or rapidly degraded after exposing to air in many cases. Another approach is amorphous oxide semiconductors. Amorphous oxide semiconductors (AOSs) have exactly attracted considerable attention because AOSs were fabricated at room temperature and used lots of application such as flexible display, electronic paper, large solar cells. Among the various AOSs, a-IGZO was considerable material because it has high mobility and uniform surface and good transparent. The high mobility is attributed to the result of the overlap of spherical s-orbital of the heavy pest-transition metal cations. This study is demonstrated the effect of thickness channel layer from 30nm to 200nm. when the thickness was increased, turn on voltage and subthreshold swing were decreased. a-IGZO TFTs have used a shadow mask to deposit channel and source/drain(S/D). a-IGZO were deposited on SiO2 wafer by rf magnetron sputtering. using power is 150W, working pressure is 3m Torr, and an O2/Ar(2/28 SCCM) atmosphere at room temperature. The electrodes were formed with Electron-beam evaporated Ti(30nm) and Au(70nm) structure. Finally, Al(150nm) as a gate metal was evaporated. TFT devices were heat treated in a furnace at $250^{\circ}C$ in nitrogen atmosphere for an hour. The electrical properties of the TFTs were measured using a probe-station to measure I-V characteristic. TFT whose thickness was 150nm exhibits a good subthreshold swing(S) of 0.72 V/decade and high on-off ratio of 1E+08. Field effect mobility, saturation effect mobility, and threshold voltage were evaluated 7.2, 5.8, 8V respectively.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1276-1279
• /
• 2005

The long-term stability of pentacene thin-film transistors (TFTs) encapsulated with a transparent $SnO_2$ thin-film prepared by ion beam assisted deposition (IBAD) was investigated. With a buffer layer of thermally evaporated 100 nm $SnO_2$ film deposited prior to IBAD process, our encapsulated OTFTs sustained its initial field-effect mobility up to one month and then gradually degraded showing only 37% reduction compared to 90% reduction of non-encapsulated OTFTs after 100 days in air ambient. The encapsulated OTFTs also exhibited superior on/off current ratio of over $10^5$ to that of the unprotected devices $({\sim}10^4)$ which was reduced from ${\sim}10^6$ before aging. Therefore, the enhanced long-term stability of our encapsulated OTFTs should be attributed to well protection of permeation of $H_2O$ and $O_2$ into the devices by the IBAD $SnO_2$ thin-film which could be used as an effective inorganic gas barrier for transparent organic electronic devices.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1140-1143
• /
• 2006

We report on the fabrication of P3HT-based thin-film transistors (TFTs) for liquid crystal display that consist of $NiO_x$, poly-vinyl phenol (PVP), and Ni for the source-drain (S/D) electrodes, gate dielectric layer, and gate electrode, respectively The $NiO_x$ S/D electrodes of which the work function is well matched to that of P3HT are deposited on a P3HT channel by electron-beam evaporation of NiO powder. The maximum saturation current of our P3HT-based TFT is about $15{\mu}A$ at a gate bias of -30 V showing a high field effect mobility of $0.079cm^2/Vs$ in the dark, and the on/off current ratio of our TFT is about $10^5$. It is concluded that jointly adopting $NiO_x$ for the S/D electrodes and PVP for gate dielectric realizes a high-quality P3HT-based TFT.

• Journal of Information Display
• /
• v.10 no.3
• /
• pp.125-130
• /
• 2009

The new organic semiconductor, which is composed of a divinylbenzene core unit and alkoxynaphthalene on both sides, 1,4-bis-2-(6-hexyloxy)naphthalen-2-yl-vinylbenzene, was synthesized via Wittig reaction. The obtained oligomer was characterized via FT-IR, mass and elemental analysis, UV-visible spectroscopy, cyclovoltammetry, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The vacuum-evaporated film was characterized via X-ray diffraction and atomicforce microscopy (AFM). It formed a highly ordered polycrystalline vacuum-evaporated film and exhibited a good field-effect performance, with a hole mobility of $0.015cm^2/V{\cdot}s$, an on/off ratio of $1.18{\times}10^5$, and a subthreshold slope of 0.69 V when it was deposited at Ts=$90^{\circ}C$ on HMDS-treated $SiO_2$.

• Journal of the Korean Applied Science and Technology
• /
• v.16 no.4
• /
• pp.313-316
• /
• 1999

Organic semiconductors based on conjugated thiophene oligomer have great potential to be utilized as an active layer for electronic and optoelectronic devices. In this study, a conjugated oligomer such as ${\alpha}$-sexithiophene (${\alpha}$-6T) thin films was prepared by the Organic Molecular Beam Deposition (OMBD), and various electrode materials were also deposited by a simple vacuum evaporation, respectively. Those films were photolithographically patterned for the electrical measurements. Electrical charact-erization of the thin film transistor with various channel length were executed and the field effect mobility of these thin film transistors were also calculated by the formula using the experimental data.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.3
• /
• pp.124-129
• /
• 2015

Organic electronics are the domain in which the components and circuits are made of organic materials. This new electronics help to realize electronic and optoelectronic devices on flexible substrates. In recent years, organic materials have replaced conventional semiconductors in many electronic components such as, organic light-emitting diodes (OLEDs), organic field-effect transistors (OFETs) and organic photovoltaic (OPVs). It is well known that organic light emitting diodes (OLEDs) have many advantages in comparison with inorganic light-emitting diodes LEDs. These advantages include the low price of manufacturing, large area of electroluminescent display, uniform emission and lower the requirement for power. The aim of this paper is to model polymer LEDs and OLEDs made with small molecules for studying the electrical and optical characteristics. The purpose of this modeling process is, to obtain information about the running of OLEDs, as well as, the injection and charge transport mechanisms. The first simulation structure used in this paper is a mono layer device; typically consisting of the poly (2-methoxy-5(2'-ethyl) hexoxy-phenylenevinylene) (MEH-PPV) polymer sandwiched between an anode with a high work function, usually an indium tin oxide (ITO) substrate, and a cathode with a relatively low work function, such as Al. Electrons will then be injected from the cathode and recombine with electron holes injected from the anode, emitting light. In the second structure, we replaced MEH-PPV by tris (8-hydroxyquinolinato) aluminum (Alq₃). This simulation uses, the Poole-Frenkel -like mobility model and the Langevin bimolecular recombination model as the transport and recombination mechanism. These models are enabled in ATLAS- SILVACO. To optimize OLED performance, we propose to change some parameters in this device, such as doping concentration, thickness and electrode materials.

• Journal of Adhesion and Interface
• /
• v.21 no.3
• /
• pp.86-92
• /
• 2020

We confirmed the effects on the device performances and the charge injection characteristics of organic field-effect transistor (OFET) by selectively differently controlling the surface energies on the contact region of the substrate where the source/drain electrodes are located and the channel region between the two electrodes. When the surface energies of the channel and contact regions were kept low and increased, respectively, the field-effect mobility of the OFET devices was 0.063 ㎠/V·s, the contact resistance was 132.2 kΩ·cm, and the subthreshold swing was 0.6 V/dec. They are the results of twice and 30 times improvements compared to the pristine FET device, respectively. As the results of analyzing the interfacial trap density according to the channel length, a major reason of the improved device performances could be anticipated that the pi-pi overlapping direction of polymer semiconductor molecules and the charge injection pathway from electrode is coincided by selective surface treatment in the contact region, which finally induces the decreases of the charge trap density in the polymer semiconducting film. The selective surface treatment method for the contact region between the electrode and the polymer semiconductor used in this study has the potential to maximize the electrical performances of organic electronics by being utilized with various existing processes to lower the interface resistance.