• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1277-1280
• /
• 2005

A high-aspect-ratio and high-resolution stainless steel shadow mask for organic thin-film transistors (OTFTs) circuit has been fabricated by a new method which combines photochemical machining, micro-electrical discharge machining (micro-EDM), and electrochemical etching (ECE). First, connection lines and source-drain holes are roughly machined by photochemical etching, and then the part of source and drain holes is finished by the combination of micro-EDM and ECE processes. Using this method a $100\;\mu{m}$ thick stainless steel (AISI 304) shadow mask for inverter can be fabricated with the channel length of $30\;\mu{m}\;and\;10\;\mu{m}\;respectively.\;The\;width\;of\;connection line\;is\;150\;\mu{m}$. The aspect ratio of the wall is about 5 and 15, respectively. Metal lines and source-drain electrodes of OTFTs were successfully deposited through the fabricated shadow mask.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.5
• /
• pp.587-592
• /
• 2015

According to increase in the use of the LED, the demand for low power consumption LED display design of the controller block has increased. In this paper, the low power LED controller block was designed through the power source supply that leads adiabatic operation from constant current source circuit operated by digital signal control. The proposed circuit was implemented using a 0.35um CMOS process. and it demonstrated linear operation of the circuit. From the simulation result, the proposed circuit was evaluated with about 82% power consumption reduction effect in comparison with conventional LED controller block. This research is expected to be helpful for the low power operation and the solution for heat problem of LED display.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.4 no.1
• /
• pp.61-67
• /
• 2011

Influence of hexamethyldisilazane(HMDS) in post processing technique by using n-butanol azeotropic distillation on the luminescence properties of YAG:Ce nanophosphor were studied. The organic solvent(n-butanol) azeotropic distillation which prevent powders from conglobation since lager molecules decrease the surface tension and more complete replace the residual water in the precipitate. HMDS that had larger molecules than that of n-butanol was added in azeotropic distillation. The phosphor synthesized from n-butanol azeotropic distillation exhibited lower agglomerate and better photoluminescence properties than that from HMDS added heterogeneous azeotropic distillation.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.4.1-4.1
• /
• 2011

Recently, circuit printing technology has been considered as a promising alternative to conventional PCB fabrication, for it can greatly reduce the manufacturing costs. Even though printed circuit has many advantages over typical subtractive technology such as fewer processes, it has some disadvantages. The major problems are low adhesion and poor resolution. Efforts to overcome these problems have been mainly focused on ink developments with a limited success. And surface treatments showed some improvements. Therefore, various plasma treatments and primer coatings on plastic substrates have been tested. Plasma treatments using hydrocarbon gases including methane and propane improved the pattern quality of the inkjet printed circuit, which are further improved upon heating of substrate. On the other hand, there is little effect on the adhesion, which is improved only by a special primer coating. The adhesion of inkjet printed circuit has been increased more than 10 times upon treatment. As for the screen printed circuits, the overall effects are less significant since there is some organic binder in the ink. Nonetheless, the treatment has strong positive effects on pattern quality and adhesion. The adhesion of 1 kgf/cm2, which is comparable with those of the conventional PCB circuits, is possible through primer coating for both screen and inkjet printed circuits. The resulting circuit also showed good thermal, mechanical and electrical properties.

• Korean Journal of Materials Research
• /
• v.30 no.4
• /
• pp.160-168
• /
• 2020

The current density in copper electroplating is directly related with the productivity; then, to increase the productivity, an increase in current density is required. This study is based on an analysis of changes in surface characteristics and mechanical properties by applying the addition of Alcian Blue (AB, C₅₆H₆₈Cl₄CuN₁₆S₄). The amount of Alcian Blue in the electrolytes is changed from 0 to 100 ppm. When Alcian Blue is added at 20 ppm, a seed layer is formed homogeneously on the surface at the initial stage of nucleation. However, crystals electroplated in electrolytes with more than 40 ppm of Alcian Blue are observed to have growth in the vertical direction on the surface and the shapes are like pyramids. This tendency of initial nucleation formation causes protrusions when the thickness of copper foil is 12 ㎛. Thereafter, a lot of extrusions are observed on the group of 100 ppm Alcian Blue. Tensile strength of groups with added Alcian Blue increased by more than 140% compare to no-addition group, but elongation is reduced. These results are due to the decrease of crystal size and changes of prior crystal growth plane from (111) and (200) to (220) due to Alcian Blue.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.228-228
• /
• 2006

Conjugated oligomers, used as models for fluorene-thiophene copolymers, are compared in terms of the microscopic morphology of thin deposits and the optical properties. The AFM images and the solid-state absorption and emission spectra are interpreted in line with the structural data, in terms of the assembly of the conjugated molecules. The compound with a terthiophene central unit and fluorene end-groups shows well-defined monolayer-by-monolayer assembly into micrometer-long strip-like structures, with a crystalline herringbone-type organization within the monolayers. Polarized confocal microscopy indicates a strong orientation of the crystalline domains within the stripes. In contrast, the compound with a terfluorene central unit and thiophene end groups forms no textured aggregates. The difference in behavior between the two compounds most probably originates from their different capability of forming densely-packed assemblies of ${\pi-pi}$ interacting molecules. These assemblies are used as active elements in organic field effect transistors designed by using soft lithography technique.

• ETRI Journal
• /
• v.27 no.2
• /
• pp.181-187
• /
• 2005

Alkoxy-substituted poly(spirobifluorene)s and their copolymers with a triphenylamine derivative have been synthesized by Ni(0)-mediated polymerization. The polymers were well soluble in common organic solvents. Pure blue-light emissions without the long wavelength emission of poly(fluorene)s have been observed in the fluorescence spectra of polymer thin films. The light emitting diodes with a device configuration of ITO/PEDT:PSS(30 nm)/polymer(60 nm)/LiF(1 nm)/Al(100 nm) have been fabricated. The electroluminescence spectra showed the blue emissions without the long wavelength emission as observed in the fluorescence spectra. The relatively poor electroluminescence quantum yield of the homopolymer (0.017% @ 20 $mA/cm^{2}$) with color coordinates of (0.16, 0.07) has been improved by the introduction of triphenylamine moiety, and the copolymer with derivative exhibited an electroluminescence quantum yield of 0.15 % at 20 $mA/cm^{2}$ with color coordinates of (0.16, 0.08). Moreover, the introduction of polar side chains to the spirobifluorene moiety enhanced the device performance and led to the quantum yields of 0.6 to 0.7 % at 20 $mA/cm^{2}$, although there was some expense of color purities.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.524-524
• /
• 2006

For decades, the pursuit of volume commercialization of low-power reflective displays with a paper-like look has been an unfulfilled dream. While steady technical progress was made throughout the late 1990s, there were still no volume products incorporating electronic paper displays (EPD) on the market. Now, microencapsulated electrophoretic display technology, also called electronic ink, has moved into volume production with a frontplane laminate (FPL) display component called E Ink Imaging Film™. This film is coated roll to roll on a flexible plastic substrate and integrated into a display module. Today, all-plastic segmented displays are being shipped as well as displays with electronic ink FPL being driven by glass TFT backplanes. A roadmap to active matrix flexible electrophoretic displays is being enabled by rapid technical progress on flexible TFT backplanes by a variety companies. Each of the approaches to these backplanes and flexible active matrix displays has different advantages for the various market segments being pursued including large format flexible displays for e-news and other reader applications, rollable displays for compact readers, and high resolution small format displays up to 400 ppi that can have fully integrated drive electronics to reduce size and drive down costs. Backplane approaches include Si on plastic, organic transistors on plastic, and Si transistors on flexible stainless steel substrate. Progress is also being made on next generation inks, including more reflective inks with higher contrast ratios. A full color 6 inch, 170 pixel per inch (PPI) active matrix display using a newer generation ink has been developed and this will be described and demonstrated. Large format segmented flexible displays will also be described.

• Proceedings of the IEEK Conference
• /
• 2009.05a
• /
• pp.48-50
• /
• 2009

This paper presents an IAQ(Indoor Air Quality) Monitoring System using equipments for measurement of fine Particle($PM1{\sim}PM10$), $CO_2$, VOCs(Volatile Organic Compounds), temperature and humidity for IAQ monitoring of subway station which millions of people use a day. The necessity of IAQ monitoring system is getting increased for more effective subway station monitoring in line with the recent government's regulation for IAQ is reinforcing. Subway Station is an unusual case. The structure of subway station is closed and complicated. Therefore when data of equipments are transferred, transmission error can happen occasionally. To prevent transmission error, an IAQ Monitoring System is needed the appropriate position and selection of equipments or sensor module. In addition IT(Information Technology) can be utilized like "WiBro(Wireless Broadband)" and "GateWay" for facilitate movement of data and construction of IAQ monitoring system of subway station.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.293-296
• /
• 2002

This paper proposes new driving methods for designing a driver independent of the current property of organic light emitting diodes (OLED) displays. The proposed methods are the Look-Up Table (LUT) and the Pulse Width Modulation (PWM). The LUT is used to handle the amount of the current for driving the OLED display panel and the PWM is applied to represent the gray scale on the OLED display panel. Segment and common drivers were implemented using delay circuits to prevent short-circuit current and a DC-DC converter was designed to supply the drivers with a power source. In particular, tile proposed methods are used for the manufacturing of 1.8" 128$\times$128 dot passive matrix OLED display panel. The designed circuit was fabricated using 0.6w, 2-poly, 3-metal, CMOS process and applied to the Personal Communication System (PCS) phone successfully.ully.