• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.452-455
• /
• 2003

[ $ZrO_2$ ] dielectric layers were grown on the p-type Si (100) substrate by metalorganic molecular beam epitaxy(MOMBE). Zrconium t-butoxide, $Zr(O{\cdot}t-C_4H_9)_4$ was used as a Zr precursor and Argon gas was used as a carrier gas. The thickness of the layers was measured by scanning electron microscopy (SEM) and the properties of the $ZrO_2$ layers were evaluated by X-ray diffraction, high frequency capacitance-voltage measurement. and HF C-V measurements have shown that $ZrO_2$ layer grown by MOMBE has a high dielectric constant (k=18-19). The growth rate is affected by various process variables such as substrate temperature, bubbler temperature, Ar, and $O_2$ gas flows.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.5
• /
• pp.351-355
• /
• 2001

Via for achieving reliable fabrication of MCM(Multichip Module) substrate was formed on photosensitive BCB layer. The MCM substrate consists of photosensitive BCB(Benzocyclobutene) interlayer dielectric and copper conductors. In order to form the vias in the photosensitive BCB layer, the process of forming the BCB layer and its via forming plasma etch using C$_2$F$\_$6//O$_2$ gas were evaluated. The thickness of the BCB layer after hard bake was shrunk down to 40% of the original. The resolution of vias formed on the BCB was 15㎛ and the slope after develop was 85 degree. AES analysis was done on two vias, one is etched in C$_2$F$\_$6/O$_2$ gas and the other isnot etched. On the via etched in C$_2$F$\_$6//O$_2$, native C was detected and the amount of native C was reduced after Ar sputter. On the via not etched in C$_2$F$\_$6//O$_2$, organic C was detected. As a result of AES, BCB residue was not removed by Ar sputter, so plasma etch is necessary for achieving reliable vias.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.78-82
• /
• 2003

For the decomposition of laundry wastewater containing Fe-EDTA produced from the steam generators in nuclear power plants, Supercritical Water Oxidation (SCWO) Process, Photocatalytic Oxidation (PO) Process, and Dielectric Barrier Discharge (DBD) Atmospheric Pressure Plasma Process were evaluated. Even though EDTA was converted over 99.98 % by the SCWO process, it was estimated that the countermeasure against corrosion of the equipment should be reinforced for the process stability. It was considered that the PO process is not appropriate for the decomposition of high concentrated laundry wastewater since the conversion ratio of EDTA was around 10 %. Finally, High efficiency of the decomposition of organic matter (methylene blue) was obtained using DBD process even low energy was supplied. However there is still room for the evaluation of EDTA decomposition in order that the DBD process should be applied for the field samples.

• Journal of Environmental Science International
• /
• v.22 no.7
• /
• pp.915-923
• /
• 2013

Decomposition of non-biodegradable contaminants such as phenol contained in water was investigated using a dielectric barrier discharge (DBD) plasma reactor in the aqueous solutions with continuous oxygen bubbling. Effects of various parameters on the removal of phenol in aqueous solution with high-voltage streamer discharge plasma are studied. In order to choose plasma gas, gas of three types (argon, air, oxygen) were investigated. After the selection of gas, effects of 1st voltage (80 ~ 220 V), oxygen flow rate (2 ~ 7 L/min), pH (3 ~ 11), and initial phenol concentration (12.5 ~ 100.0 mg/L) on phenol degradation and change of $UV_{254}$ absorbance were investigated. Absorbance of $UV_{254}$ can be used as an indirect indicator of phenol degradation and the generation and disappearance of the non-biodegradable organic compounds. Removal of phenol and COD were found to follow pseudo first-order kinetics. The removal rate constants for phenol and COD of phenol were $5.204{\times}10^{-1}min^{-1}$ and $3.26{\times}10^{-2}min^{-1}$, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.7
• /
• pp.599-603
• /
• 2003

Ferroelectric B $i_4$$_{-x}$N $d_{x}$ $Ti_3$ $O_{12}$ (BNdT) thin films with the composition(x=0.75) were prepared on Pt/Ti/ $SiO_2$(100) substrate by metal-organic deposition. The films were annealed by various temperatures from 550 to $650^{\circ}C$ and then the electrical and structural characteristics of BNdT films were investigated for the application of FRAM. Electrical properties such as dielectric constant, 2Pr and capacitance were quite dependent on the thermal heat treatment. The measured 2Pr value on the BNdT capacitor annealed at $650^{\circ}C$ was 56$\mu$C/$\textrm{cm}^2$ at an applied voltage of 5V. In fatigue characteristics value remained constant up to 8$\times$10$^{10}$ read/write switching cycles at a frequency of 1Mhz regardless of annealing temperatures.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.75-78
• /
• 2004

$Bi_{3.25}Eu_{0.75}Ti_3O_{12}$ (BET) thin films were deposited on the $LaNiO_3$ (LNO (100))/Si and Pt/Ti/$SiO_2$/Si substrates by the metal-organic decomposition method. Structural and dielectric properties of BLT thin films for the applications in nonvolatile ferroelectric random access memories were investigated. Both the structure and morphology of the films were analyzed by x-ray diffraction (XRD) and atomic force microscope (AFM). Even at low temperatures $650^{\circ}C$, the BET thinfilms were successfully deposited on LNO bottom electrode and exhibited (001) and (117) orientation. Compared with the Pt electrode films, the BET thin films on the LNO electrode annealed at $650^{\circ}C$ showed better dielectric constantsand remanent polarization. The BET thin films on the LNO electrode for the annealing temperature of $650^{\circ}C$, the remanent polarization Pr and coercive field were $45.6\;C/cm^2$ and 171 kV/cm, respectively.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.245-247
• /
• 1996

The ferroelectric $Pb(Zr_xTi_{1-x})O_3$ (20/80, 80/20) heterolayered thin films were fabricated from an alkoxide-based by Sol-Gel method. The PZT(20/80) and PZT(80/20) stock solution were made and spin-coated on the Pt/Ti/$SiO_2$/Si substrate by turns. Each layers were baked to remove the organic materials at 300[$^{\circ}C$] for 30[min]. and sintered at 650[$^{\circ}C$] for 1[hr]. This procedure was repeated 5 times. At this time the thickness of thin films were about 4000[$\AA$]. Relative dielectric constant and remanent polarization of the PZT heterolayered thin films were 1200, 27.10 [${\mu}C/cm^2$], respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.395-395
• /
• 2007

We report on the fabrication of soluble pentacene-based thin-film transistors (TFTs) that consist of $NiO_x$, poly-vinyl phenol (PVP), and Ni for the source-drain (SID) electrodes, gate dielectric, and gate electrode, respectively. The $NiO_x$ SID electrodes of which the work function is well matched to that of soluble pentacene are deposited on a soluble pentacenechannel by sputter deposited of NiO powder and show a moderately low but still effective transmittance of ~65% in the visible range along with a good sheet resistance of ${\sim}40{\Omega}/{\square}$. The maximum saturation current of our soluble pentacene-based TFT is about $15{\mu}A$ at a gate bias of -40showing a high field effect mobility of $0.06cm^2/Vs$ in the dark, and the on/off current ratio of our TFT is about $10^4$. It is concluded that jointly adopting $NiO_x$ for the S/D electrodes and PVP for gate dielectric realizes a high-quality soluble pentacene-based TFT.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.4
• /
• pp.325-331
• /
• 2007

In this study, the inter-metal dielectric material of FSG was changed by low-k material in $0.13{\mu}m$ foundry-compatible technology (FCT) device process based on fluorinated silicate glass (FSG). Black diamond (BD) was used as a low-k material with a dielectric constant of 2.95 for optimization and yield-improvement of the low-k based device process. For yield-improvement in low-k based device process, some problems such as photoresist (PR) poisoning, damage of low-k in etch/ash/cleaning process, and chemical mechanical planarization (CMP) delamination must be solved. The PR poisoning was not observed in BD based device. The pressure in CMP process decreased to 2.8 psi to remove the CMP delamination for Cu-CMP and USG-CMP. $H_2O$ ashing process was selected instead of $O_2$ ashing process due to the lowest condition of low-k damage. NE14 cleaning after ashing process lot the removal of organic residues in vias and trenches was employed for wet process instead of dilute HF (DHF) process. The similar-state of SRAM yield was obtained in Cu/low-k process compared with the conventional $0.13{\mu}m$ FCT device by the optimization of these process conditions.

• Journal of Surface Science and Engineering
• /
• v.34 no.5
• /
• pp.475-480
• /
• 2001

Diffusion of Cu into the low-k para-xylene based plasma polymer (pXPP) thin films deposited by plasma-enhanced chemical vapor deposition using the para-xylene precursor was comparatively measured using various methods. Cu layer was deposited on the surfaces of pXPPs treated by $N_2$ plasma generated in a magnetically enhanced inductively coupled plasma reactor. Diffusion characteristics of Cu into pXPPs were measured using Rutherford backscattering spectroscopy (RBS), secondary ion mass spectroscopy (SIMS), cross-sectional transmission electron microscopy (XTEM), and current-voltage (I-V) measurements for the vacuum-annealed Cu/pXPPs for 1 hour at $450^{\circ}C$ and were compared. The results showed a correlation between the I-V measurement and SIMS data are correlated and have a sensitivity enough to evaluate the dielectric properties but the RBS or XTEM measurements are not sufficient to conclude the electrical properties of low-k dielectrics with Cu in the film bulk. The additional results indicate that the pXPP layers are quite resistant to Cu diffusion at the annealing temperature of $450^{\circ}C$ compared to the other previously reported organic low-k materials.