• 보존과학연구
• /
• 통권29호
• /
• pp.5-18
• /
• 2008

Hanji among paper, which is material for support of the organic artifact such as painting and Thangkas, is given as much importance as the original material in the conservation treatment of artifacts. This lining paper can go through physical and chemical deterioration due to its organic nature, and inflict serious damage to the original materials of the artifact. There is a lot of difficulty in keeping continuous production of the paper mulberry fiber based on lining paper due to a short supply of raw material and discontinuation of traditional method. Also restoration and conservation treatment is done by relying only on the knowledge and skill of few experts without any recognized manual based on scientific analysis. In this study, we evaluated the stability of lining paper which is used to support organic artifact. As the result of experiments, this lining paper was made from mulberry tree in Korea and produced by means of oebal method, but was not treated by starch in its surface.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 추계학술대회 논문집
• /
• pp.219-225
• /
• 2000

This study is to develop a Fe-based disc brake lining with sponge structure for rolling stock of 150km/h train and to concept design with 3 groove type for brake disc reducing hot hair-crack and certainly friction coefficient. The developing brake lining would be to presumption of saving 300 million won during one year

• 보존과학연구
• /
• 통권30호
• /
• pp.93-102
• /
• 2009

This study was carried out to investigate the effect of artificial accelerated ageing treatment on the permanence of lining papers produced from Korea and Japan. As time gone by, organic cultural properties are affected by chemical and physical deterioration because of various factors including the conditions of preservation environment and their material properties. In the public historical storage or owned as private collections, are vulnerable to sever amages caused by poor preservation environment as well as by other natural factors. In this study, the deterioration behaviors of lining paper in optical & mechanical properties were discussed. Overall, lining papers produced from Korea showed lower reduction in mechanical strength properties compared to the lining papers produced from Japan.

• 한국구조물진단유지관리공학회 논문집
• /
• 제13권3호통권55호
• /
• pp.110-118
• /
• 2009

산간 지형이 많은 국내 여건상 물류수송 및 교통 등을 위한 터널 구조물의 활용성은 매우 높다. 최근 현장에서는 공기단축 및 원가절감을 위하여 터널 굴착과 라이닝 콘크리트의 타설을 병행하는 공법이 진행되면서 굴착에 의한 진동 등의 영향으로 콘크리트 구조물 초기 재령에서 균열 및 내구성능 저하 문제가 발생하고 있다. 본 연구에서는 터널 라이닝용 콘크리트 배합에 있어서 보강재를 강섬유와 더불어 최근 국내에서 개발된 폴리아미드 섬유를 병행 사용한 콘크리트의 역학적 특성을 실험적으로 검토하였다. 또한 유 무기 섬유보강 터널 라이닝 콘크리트 부재의 하중-변위와 하중-변형률 관계를 모형 실험으로 평가하였다. 실험 결과, 보통 콘크리트에 강섬유와 폴리아미드 섬유 보강재를 하이브리드화하여 사용한 콘크리트 부재에서 구조 성능이 증진됨을 확인할 수 있었다.

• 한국정밀공학회지
• /
• 제29권11호
• /
• pp.1178-1182
• /
• 2012

The organic linings at flue gas desulfurization systems (FGD system) in power plant have the excellent chemical properties but, lose the anticorrosive properties according to the aging with environment conditions. The properties of the organic linings depend on the manufacturing company. Therefore, the basic properties of organic linings for the preestimate of life time should be examined by conducting the aging and the bond strength test according to temperature. The pre-aging samples were compared with the post-aging samples. The temperature conditions of the aging process were 70, 150 and $200^{\circ}C$. The bond strength was calculated and the cross sections of fracture surface were examined by optical microscope and SEM. The $T_g$ was examined by DSC, DTA and TGA.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.72-78
• /
• 2001

An experimental investigation was conducted to examine the tribological behavior of NAO (non-asbestos organic) type brake linings containing different volume ratios of graphite and antimony trisulfide (Sb$_2$S$_3$). In order to investigate the effect of the solid lubricants on brake performance, three different friction tests (pressure, speed, and temperature sensitive tests) were carried out using a scale dynamometer. The test results showed that the friction characteristics were strongly affected by the type and the amount of solid lubricants in the brake lining. It was found that the brake linings with both solid lubricants were better in friction stability due to the complementary role of the two disparate lubricating properties at various pressure and speed conditions. In particular, the brake lining containing higher concentrations of graphite showed better fade resistance than others during high temperature friction test.

• Corrosion Science and Technology
• /
• 제3권1호
• /
• pp.20-25
• /
• 2004

In order to clarify the durability of protective coatings for maritime steel structures, various anti-corrosive organic coated steel samples were exposed for twelve years in semitropical marine environment at Miyakojima Island, Okinawa, JAPAN. Samples were various organic coated steel pipes, 4.0 m in length and 150 mm in diameter. While the bare steel pipe entirely corroded in 4.5 mm thickness in four and half years, these organic coated steel pipes exhibited protective appearances after twelve-year-exposure except for the defect in the coatings. Polyethylene (PE) lining pipe exhibited a good protective performance. Urethane painted pipe was also good but some barnacles stuck to its surface. A combination of petrolatum tape and FRP cover showed sufficient corrosion resistance for steel surface. The correlation in results between exposure and laboratory acceleration test was examined. It was found that salt spray test (SST) results corresponded to rusted area of scratched portion and that adhesion change of coating layer corresponded to the rotating immersion test result. Among the on-site measured data, volume resistivity is utilized for the index of corrosion protection performance of organic coating.

• Tribology and Lubricants
• /
• 제17권5호
• /
• pp.351-357
• /
• 2001

Tribological behavior of NAO type brake linings containing different volume ratios of graphite and Sb$_2$S$_3$ was investigated using a scale dynamometer. Three different test modes consisting of stop, drag, and fade tests were employed to elucidate the effect of the solid lubricants on brake performance. Results of this work showed that the two solid lubricants, graphite and Sb$_2$S$_3$, significantly affected friction characteristics at various braking situations. Compared with the brake linings containing a single lubricant, the brake linings containing both solid lubricants showed better friction stability due to the synergistic effect of the two disparate lubricants during the stop and the drag test. In particular, in the case of containing two solid lubricants, the brake lining with higher contents of graphite showed better fade resistance than others.

• Journal of Advanced Marine Engineering and Technology
• /
• 제20권2호
• /
• pp.75-75
• /
• 1996

The rapid expansion for the auto-industry and the worldwide trend toward non-asbestos friction materials for brake lining force our industry to transfer into non-asbestos ones from asbestos-based friction materials. Furthermore, it is imperative for the friction materials to have technological excellence and lower production cost to be competitive in the world market. There is no known theoretical procedures to formulate friction materials. It, rather, depends on the trial and error process. Thus, it is quite clear how important it is to accumulate the know-how on the formulation and manufacturing the friction material. This study concerns the practical ways of conceptualizing the formulation and optimizing the manufacturing process. This study focused on the development of formulation for non-asbestos friction material as well as deriving the physical properties of the trial product to prove its validity and applicability. Elaboration of the formula and optimizing scheme of the manufacturing process to get better quality are also sought. Physical properties were obtained by constant velocity test dynamotest, hardness test and strength test. Differential scanning calorimeter was also used to analyze the thermal reactions of organic constituents, microstructures, bond effects, and degree of mixture.

• Journal of Advanced Marine Engineering and Technology
• /
• 제20권2호
• /
• pp.7-14
• /
• 1996

The rapid expansion for the auto-industry and the worldwide trend toward non-asbestos friction materials for brake lining force our industry to transfer into non-asbestos ones from asbestos-based friction materials. Furthermore, it is imperative for the friction materials to have technological excellence and lower production cost to be competitive in the world market. There is no known theoretical procedures to formulate friction materials. It, rather, depends on the trial and error process. Thus, it is quite clear how important it is to accumulate the know-how on the formulation and manufacturing the friction material. This study concerns the practical ways of conceptualizing the formulation and optimizing the manufacturing process. This study focused on the development of formulation for non-asbestos friction material as well as deriving the physical properties of the trial product to prove its validity and applicability. Elaboration of the formula and optimizing scheme of the manufacturing process to get better quality are also sought. Physical properties were obtained by constant velocity test dynamotest, hardness test and strength test. Differential scanning calorimeter was also used to analyze the thermal reactions of organic constituents, microstructures, bond effects, and degree of mixture.