• Journal of Animal Environmental Science
• /
• v.19 no.1
• /
• pp.1-8
• /
• 2013

Slurry treatments included peanut shell, palm golden fiber, almond hull, which was added 2% of the amount of slurry, and non-treatment control (n=4 each group). Levels of odorous compounds were measured from the liquid slurry incubated in $20^{\circ}C$ for 2 wk in chamber whose structure is similar to slurry pit. Concentration of phenols and indoles was higher (p<0.05) in control (48.4, 4.0 ppm) compared to almond hull (31.5, 1.4 ppm) or palm golden fiber (29.1, 1.6 ppm) group. Short chain fatty acid (SCFA) level was lowest (p<0.05) in control (2,121 ppm) but highest in peanut shell group (3,640 ppm). Branched chain fatty acid (BCFA) concentration was highest (p<0.05) in peanut shell (296 ppm), but lowest in almond hull (90 ppm). Taken together, concentration of odorous compounds was decreased by addition of almond hull in pig slurry by which crude fiber and non-digestible fiber (NDF) may act as a carbon source.

• Journal of Korean Society for Atmospheric Environment
• /
• v.22 no.6
• /
• pp.767-778
• /
• 2006

This study was carried out to evaluate the temporal variations of VOCs at an urban site, and to compare the concentrations of VOCs at an urban site in Daegu with those at a suburban site in Gyeongsan. Three hourly VOC samples in the ambient air were collected using a sequential tube sampler (STS 25, Perkin Elmer) throughout two weeks during May and July representing spring and summer seasons, respectively. The VOC concentrations were determined by an automatic thermal desorption apparatus with GC/MS analysis. A total of 12 VOCs of environmental concern were determined, which are chloroform, benzene, trichloroethylene, toluene, tetra-chloroethylene, ethylbenzene, m+p-xylenes, o-xylene, styrene, 1,3,5- and 1,2,4-trimethylbenzenes. Among 12 target VOCs, the most abundant compound appeared to be toluene, being followed by xylenes. The mean concentrations at the urbn site were 1.2 pub for benzene and 20.4 ppb for toluene (n=221) while the mean levels at the suburban site were 0.9 ppb and 4.3 ppb for benzene and toluene (n=96), respectively. The urban site concentrations were typically several-fold higher than those measured at the suburban site. It was found that general trends of VOC levels were significantly dependent on traffic conditions at the sampling site since VOC concentrations were at their maximum during rush hours, i.e. $9{\sim}12a.m$ and $6{\sim}9p.m$. Statistical investigations were conducted to investigate any significant relationships between VOC concentrations and affecting factors. Calculated correlation coefficients among VOCs were positively significant at a level of 0.05 in most cases. Increased concentrations of toluene in the urban site were estimated to reflect the effect of large industrial sources, mainly from textile industry.

• Korean Journal of Environmental Biology
• /
• v.26 no.2
• /
• pp.109-114
• /
• 2008

To evaluate the extent of Sea-Nine 211 (4,5-dichloro-2-n-octyl-3(2H) isothiazolone), one of the alternating organic booster compound used in antifouling paint to replace TBT, on marine benthic bivalve, we injected Sea-Nine 211 to clam, Pseudocardium sachalinensis, and then determined some xenobiotics metabolizing enzyme activities, especially EROD (ethoxyresorufin deethylase) and MROD (methoxyresorufin demethylase), in digestive gland during 4 day-exposure period. Moreover, the results were compared with those of TBT exposed clam. CYP1A1 dependant EROD activity in both the Sea-Nine 211 and the TBTC exposure groups showed no significant differences compared to those of the solvent control group. CYP1A2 dependant MROD activity in Sea-Nine 211 exposure group was significantly induced, but no significant difference was obtained in the TBTC exposure group. These results indicate that Sea-Nine 211 demonstrated a tendency to induce MROD activity, while TBTC inhibits the activities of this enzyme.

• Restorative Dentistry and Endodontics
• /
• v.28 no.4
• /
• pp.326-333
• /
• 2003

Ormocer has organic-inorganic compound polymers. One of advantages of ormocer is reduced polymerization shrinkage. The purpose of this study was to compare the amount of contraction shrinkage of composite resins and ormocers. Additionally, the time of each material when there is no further change of contraction shrinkage was analysed. Four brands of composite resins (P-60. Surefil, Z-250 and Denfil) and two brands of ormocers (Definite and Admira) were used. 20 seconds, 40 seconds and 60 seconds of curing times were given. Contraction shrinkage of them were measured using a linometer for 80 seconds. The effect of material and curing time to contraction shrinkage at the time of 80 seconds was analysed by two-way ANOVA. The effect of time to contraction shrinkage was analysed by one-way ANOVA and the time when there was no further change of the contraction shrinkage was analysed. The results are as follows: 1. P-60, Definite, Z-250 and Denfil had no further change of contraction shrinkage from the time of 20 seconds, and Surefil and Admira had no further change of contraction shrinkage from the time of 10 seconds. 2. Statistical analysis revealed volumetric shrinkage varied among material (p<0,05). No significant difference of contraction shrinkage among different curing times was found, and there was no effect of interaction between materials and curing times to contraction shrinkage. 3. Definite and Admira showed the statistically same contraction shrinkage with those of Z-250 and P-60. which is higher than that of Surefil and lower than that of Denfil (p<0.05).

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.387-392
• /
• 2005

For the production of further functional bio-degradable plastic(polybutylene succinate:PBS) with $TiO_{2}$ as photocatalyst, which shows the decomposition of detrimental organic compound and pollutant under ultraviolet irradiation, we attempted to prepare $TiO_{2}$ coatings on PBS substrate by HVOF and plasma spraying techniques under various conditions. The microstructures of coatings were characterized with SEM and XRD analysis, and the photocatalytic efficiency of coatings was evaluated through the photo degradation of gaseous acetaldehyde. The effects of primary particle size and spraying parameters on the formation behavior, photo catalytic performance and mechanical characteristics of the coatings have been investigated. The results indicated that with respect to both the HVOF sprayed $P_{200}$ and $P_{30}$ coatings, the high anatase ratio off 100% can be achieved regardless of fuel gas pressure. On the other hand, the HVOF sprayed $P_{7}$ coating exhibited largely decreased anatase ratio (from 100% to 49.1%) with increasing the fuel gas pressure, which may be attributed to the much higher susceptibility to heat of 7nm agglomerated powder. In terms of photocatalytic efficiency, HVOF sprayed $P_{200}$ and $P_{30}$ coatings seem to predominate as compared to that of plasma sprayed $P_{200}$ coatings owing to the higher anatase ratio. However, the HVOF sprayed $P_{7}$ coatings didn't show the photo catalytic activity, which may result from the extremely small reaction surface area to the photo-catalytic activity and low anatase ratio. Such functional PBS with new roles is expected to cosiderably contribute to the reduction of aggravated environmel problem.

• Korean Journal of Weed Science
• /
• v.17 no.4
• /
• pp.407-412
• /
• 1997

Allelopathic activity of methanol extract from medicinal plants was determined based on the inhibition of germination, shoot and root length of Echinochloa crus-galli. The response was depended on the source of extracts and concentrations. Of the 20 test plants tested, Cnidium officinale showed most inhibition according to germination, shoot and root length of E. crus-galli. Based on the plant parts, the root extract of C. officinale had more inhibitory effect on E. crus-galli than the stem+leaf extract. Phytotoxic effects of the root extract on E. crus-galli showed 75% inhibition of seed germination, 95% inhibition of shoot growth, and 100% inhibition of root growth at the concentration of 1g/petridish. Sequential partitioning of root extract with organic solvents with increasing polarity showed that the ethylacetate fraction had the greatest inhibitory effect on E. crus-galli. Germination was not inhibited at any rate of ethylacetate fraction but shoot and root growth, were significantly inhibited even at 2mg/petridish. This indicates that the most toxic phytotoxin present in the root extract may be moderate polar compound.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.553-553
• /
• 2013

상압 플라즈마 기술은 표면처리, 온존 발생장치, VOC (Volatile Organic compound) 제거등 다양한 산업분야에서 응용되고 있다. 상압플라즈마 기술 또한 DBD (Dielectric barrier discharge), Griding Arc, SDIP (Surface Discharge Induced Plasma) 등 다양한 기술들이 개발되어져 왔다. VOC를 제거하기 위한 다양한 플라즈마 기술중 특히 BDB 방법과 SDIP 기술들은 플라즈마에 의한 VOC 분해 뿐만 아니라 오존 발생을 통하여 VOC성분을 분해하는 것으로 알려져 있으며 효율이 매우 뛰어난 것으로 보고 되고 있다. 그러나 BDB 방전의 경우 방전이 발생하는 간격이 매우 작아 공기를 정화시키기 위해 좁은 유로를 통하여 일정넓이를 이동하여하 하기 때문에 압력감소가 심하며 이를 개선하기위해 다단으로 설계할 경우 구조가 복잡하고 가격이 고가인 단점이 있다. 본 연구에서는 두 개의 면 전극이 마주보는 형태로 된 DBD 구조의 단점을 보완하기 위하여 빗살무늬 모양의 다층구조의 선형전극으로 구조를 변화시켜 전극에 의한 압력감소를 방지하고 효율적으로 플라즈마 및 오존을 발생시킬 수 있는 VOC제거용 상압 플라즈마 발생장치를 개발하였다. 또한 플라즈마 발생 및 오존발생량이 우수한 것으로 알려져 있는 SDIP 장치 또한 제작하여 비교 평가를 하였다. 제작된 플라즈마 발생장치는 60 Hz와 20kHz의 교류 고압파워 서플라이를 이용하여 플라즈마 발생실험을 진행하였다. 선행 연구에서는 60 Hz의 고압 파워 서플라이를 이용하여도 플라즈마 방전이 잘 된다고 보고되었는데 본 실험에서 60 Hz 파워 서플라이를 사용할 경우 15 kV 이상이 인가될 때 아주 약하게 오존이 발생하는 현상이 관찰되었으나 육안으로 구분이 될 만큼의 플라즈마 방전은 발생하지 않았다. 20kHz의 고압파워 서플라이를 사용한 경우에는 비교적 낮은 전압인 7 kV에서 방전이 관찰되었으며 분당 22 mg의 오존이 발생하였다. SDIP를 이용한 경우 플라즈마가 발생하는 조건은 SDIP의 기하학적 형상에 많이 의존하게 된다. 본 실험에 SDIP 장치는 매우 낮은 전압에서 방전을 시작하였다. 기존의 DBD와는 다르게 1.7 kV에서 플라즈마 발생하였으며 1.8 kV에서 정상적인 플라즈마 방전이 발생하였다. 이때 분당 3.1 mg의 오존이 발생하였다. 오존 발생양은 앞에 빗살형 플라즈마 방전장치에 비하여 낮은데 인가되는 전력을 고려하면 입력된 전기 에너지당 오존발생양은 비슷한 수준이였다.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.5
• /
• pp.487-493
• /
• 2006

Reductive dechlorination of chlorophenols by nickel coated iron was investigated to understand the feasibility of using Ni/Fe for the in situ remediation of contaminated groundwater. Zero Valent Iron(ZVI) was amended with Ni(II) ions to form bimetal(Ni/Fe). Dechlorination of five chlorophenol compounds and formation of intermediates were examined using Ni/Fe. Rate constant for each reaction pathway was quantified by the numerical integration of a series of differential rate equation. Experimental results showed that the sequence of hydrodechlorination rate constant was in the order of 2-CP>4-CP>2,4-DCP>2,4,6-TCP>2,6-DCP. The hydrodechlorination pathways for the conversion of each chlorophenol compound involves a full dechlorination to phenol via both concerted and stepwise mechanisms. Reaction pathways and corresponding kinetic rate constants were suggested based on the experiments and numerical simulations.

• Journal of Environmental Science International
• /
• v.20 no.11
• /
• pp.1465-1481
• /
• 2011

The accuracy of ozone sensitivity coefficients estimated with HDDM (High-order Decoupled Direct Method) can vary depending on the $NO_x$ (Nitrogen Oxides) and VOC (Volatile Organic Compound) conditions. In order to evaluate the applicability of HDDM over the Seoul Metropolitan Area (SMA) during a high ozone episode in 2007 June, we compare BFM (Brute Force Method) and HDDM in terms of the $1^{st}$-order ozone sensitivity coefficient to explain ozone change in response to changes in NOx and VOC emissions, and the $2^{nd}$-order ozone sensitivity coefficient to represent nonlinear response of ozone to the emission changes. BFM and HDDM estimate comparable ozone sensitivity coefficients, exhibiting similar spatial and temporal variations over the SMAduring the episode. NME (Normalized Mean Error) between BFM and HDDM for the episode average $1^{st}$- and $2^{nd}$-order ozone sensitivity coefficients to NOx and VOC emissions are less than 3% and 9%, respectively. For the daily comparison, NME for the $1^{st}$- and $2^{nd}$-order ozone sensitivity coefficients are less than 4% ($R^2$ > 0.96) and 15% ($R^2$ > 0.90), respectively. Under the emission conditions used in this study, two methods show negative episode average $1^{st}$-order ozone sensitivity coefficient to $NO_x$ emissions over the core SMA. The $2^{nd}$-order ozone sensitivity coefficient to $NO_x$ emissions leads ozone to respond muchnonlinear to the reduction in $NO_x$ emissions over Seoul. Nonlinear ozone response to reduction in VOC emissions is mitigated due to the $2^{nd}$-order ozone sensitivity coefficient which is much smaller than the $1^{st}$-order ozone sensitivity coefficient to the emissions in the magnitude.

• Journal of Environmental Science International
• /
• v.19 no.7
• /
• pp.829-841
• /
• 2010

The estimation of a biogenic volatile organic compound (BVOC, especially isoprene) and the influence of isoprene emissions on ozone concentrations in the Greater Busan Area (GBA) were carried out based on a numerical modeling approach during a high ozone episode. The BVOC emissions were estimated using a biogenic emission information system (BEIS v3.14) with vegetation data provided by the forest geographical information system (FGIS), land use data provided by the environmental geographical information system (EGIS), and meteorological data simulated by the MM5. Ozone simulation was performed by two sets of simulation scenarios: (1) without (CASE1) and (2) with isoprene emissions (CASE2). The isoprene emission (82 ton $day^{-1}$) in the GBA was estimated to be the most dominant BVOC followed by methanol (56) and carbon monoxide (28). Largest impacts of isoprene emissions on the ozone concentrations (CASE2-CASE1) were predicted to be about 4 ppb in inland locations where a high isoprene was emitted and to be about 2 ppb in the downwind and/or convergence regions of wind due to both the photochemical reaction of ozone precursors (e.g., high isoprene emissions) and meteorological conditions (e.g., local transport).