• Journal of Ocean Engineering and Technology
• /
• v.22 no.1
• /
• pp.37-45
• /
• 2008

The purpose of this study is to quantify the settling velocities of cohesive sediments from Han estuary and to evaluate their local variation within Han estuary. This study also includes an estimation of their spatial variation, for which the settling velocities of cohesive sediments from Han estuary arecompared with those for sediments from other regions. At the same time, physical-chemical properties, such as grain size distribution, the percentage of organic contents, mineralogical composition etc are measured in this study in order to examine their correlation with settling velocities and their effect on settling velocities. Results from settling tests shaw that the settling velocities of Han estuary mud varies in the range of two orders of magnitude(from 0.01 to 1.5 mm/sec) over the corresponding concentration range of 0.1 to 80 g/L, and a feature of the settling velocity profile is quite different in quantity as compared to those of previous studies for muds from other regions. Particularly in the flocculated settling region, the settling velocity for Han estuary muds is shown to be larger than that of Saemankeum and Keum estuary sediments, while in the hindered settling region all three sediments are shown to have a similar settling velocity. However, local variability of the settling velocities within Han estuary is shown to be insignificant.

• Geomechanics and Engineering
• /
• v.31 no.4
• /
• pp.365-373
• /
• 2022

In order to investigate the damage evolution law of rock specimens under cyclic loading, cyclic loading tests under constant loads with different amplitudes were carried out on limestone specimens with high strength and brittleness values using acoustic emission (AE) technology and the energy evolution and AE characteristics were evaluated. Based on dissipated energy density and AE counts, the damage variable of specimen was characterized and two damage evolution processes were analyzed and compared. The obtained results showed that the change of AE counts was closely related to radial deformation. Higher cyclic loading values result in more significant radial strain of limestone specimen and larger accumulative AE counts of cyclic loading segment, which indicated Felicity effect. Regarding dissipated energy density, the damage of limestone specimen was defined without considering the influence of radial deformation, which made the damage value of cyclic loading segment higher at lower amplitude loads. The damage of cyclic loading segment was increased with the magnitude of load. When dissipated energy density was applied to define damage, the damage value at unloading segment was smaller than that of AE counts. Under higher cyclic loading values, rocks show obvious damage during both loading and unloading processes. Therefore, during deep rock excavation, the damages caused by the deformation recovery of unloading rocks could not be ignored when considering the damage caused by abutment pressure.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.10 no.1
• /
• pp.90-95
• /
• 2014

Local wall thinning is a point of concern in almost all steel structures such as pipe lines covered with a thermal insulator made up of materials with low thermal conductivity(fiberglass or mineral wool); hence, Non Destructive Technique(NDT) methods that are capable of detecting the wall thinning and defects without removing the insulation are necessary. In this study we developed a Pulsed Eddy Current(PEC) system to detect the wall thinning of Ferro magnetic steel pipes covered with fiber glass thermal insulator and shielded with Aluminum plate. The developed system is capable of detecting the wall thickness change through an insulation of thickness 10cm and 0.4mm aluminum shielding. In order to confirm the thickness change due to wall thinning, two different sensors, a hall sensor and coil sensor were used as a detecting element. In both cases, the results show a very good change corresponding to the thickness change of the test specimen. During these experiments a carbon steel tube of diameter 210mm and a length of 620mm, which is covered with insulator of 95mm thickness was used. To simulate the wall thinning, the thickness of the tube is changed for a specified length such as 2.5mm, 5mm and 8 mm from the inner surface of the tube. A 0.4mm thick Aluminum plate was covered on the Test specimen to simulate the shielding of the insulated pipelines. For both hall sensor and coil detection methods Fast Fourier transform(FFT) was calculated using window approach and the results for the test specimen without Aluminum shielding were summarized which shows a clear identification of thickness change in the test specimen by comparing the magnitude spectra. The PEC system can detect the wall thinning under the 95 mm thickness insulation and 0.4 mm Al shielding, and the output signal showed linear relation with tube wall thickness.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.10
• /
• pp.82-88
• /
• 2014

This paper presents the results of model tests for the attachment process of lightning leader to ground which is one of poorly understood processes of cloud-to-ground lightning discharges. In order to simulate the attachment process of lightning leader to ground, we investigated the discharge characteristics of air gap between the tip of needle-shaped electrode and the soil surface as a parameter of moisture content in soils when the positive and negative $1.2/50{\mu}s$ lightning impulse voltages are applied. The breakdown voltage and the discharge light were observed. As a result, the attachment processes of lightning leader to ground are strongly dependent on the grain size and the moisture content of soils. The time to breakdown was shortened with increasing the magnitude of incident impulse voltages. The delay time from application of the highest voltage to breakdown in sand is shortened with increasing the moisture content. The delay time from application of the voltage to breakdown in gravel varied from about $0.5{\mu}s$ to several ${\mu}s$. As the moisture content in soil increases, the breakdown voltages are decreased and the breakdown voltage versus time to breakdown curves are shifted toward the lower side. The results obtained in this work are similar to those for non-uniform air gap stressed by lightning impulse voltages.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.4 no.2
• /
• pp.256-262
• /
• 2001

Viscous solutions of supersonic side jet nozzle and supersonic jet impinging on a flat plate are simulated using three-dimensional Navier-Stokes solver. For rapid and abrupt control of a missile in supersonic flight, side jet on a missile body is found to be a useful devise as evidenced by recent missile development at several nations. The magnitude of the side jet and the duration of it decide the level of control of such a missile system. The aerodynamic characteristics of the side jet devise itself are examined in terms of key parameters such as the side jet nozzle geometry, the chamber pressure and temperature. On the other hand, the jet impinging flow structure exhibits such complex nature as shock shell, plate shock and Mach disk depending on the flow parameters. Among others, the dominant parameters are the ratio of the nozzle exit pressure to the ambient pressure and the distance between the nozzle exit plane and the impinging plane. As the plate is placed close to the nozzle, the computed wall pressure at or near the jet center oscillates with large amplitude with respect to the mean value. The amplitude of wall pressure fluctuations subsides as the plate/nozzle distance increases, and the frequency of the wall pressure is estimated on the order of 10.0 KHz. Objectives of this paper are to show accurate simulation of nozzle flow itself and to demonstrate the jet flow structure when the jet interacts with a wall at a close range.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.5
• /
• pp.22-28
• /
• 2003

This paper describes the frequency dependence of the grounding impedance. In order to propose the evaluation method of the transient response of powered grounding systems, the grounding impedances were measured with varying the frequency of incoming currents by way of the variable frequency inverter and band pass filter. The magnitude and phase of the grounding impedance were analyzed in the frequency range of 20 [Hz]∼2.1[kHz]. The grounding impedance were increased with increasing the frequency of the test current. The grounding impedance at the frequency of 2[kHz] in the actual 22.9[kV] substation grounding system was approximately 3 times as large as the 60[Hz] grounding impedance. It was found that the frequency dependence of the grounding impedance is mainly subject to the inductive reactance of the grounding conductors. As a result, it is critical to determine the shape and size of grounding grid reducing the resultant inductance in grounding systems for lightning surge protection.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.5
• /
• pp.576-581
• /
• 1999

Effects of signal sequences, protein sizes and dissolved oxygen on the secretion of human lysozyme from a recombinant yeast were experimentally characterized. The systems consisted of Saccharomyces cerevisiae host SEY2102 that was transformed with two different plasmids. These plasmids were identical with an exception to the plasmid pMC614, which contained the native yeast MFα1 sequence and the plasmid pMC632 with the non-native rat α-amylase signal sequence. The expression of human lysozyme was controlled by the ADHI promoter. The native yeast MFαl signal sequence was more efficient than the non-native rat α-amylase signal sequence in directing the secretion of human lysozyme. Lysozyme secreted with the α-amylase signal was retained inside the cells and released to the medium very slowly, thereby causing a lower cell growth rate and a decreased product secretion rate. Lysozyme was secreted more efficiently than invertase, which is an order of magnitude bigger in molecular size compared to lysozyme, which was under the direction of the MFαl signal sequence, suggesting that protein sizes may affect the secretion efficiency. When expressed in anaerobic conditions in the medium where the ADHI promoter was derepressed, the amount of lysozyme secreted was about twice higher than that of the aerobic culture. However, the secretion rates were identical. This result showed that the dissolved oxygen level may affect the efficiency of protein secretion only, and not the secretion rate of the product protein.

• Korean Chemical Engineering Research
• /
• v.58 no.2
• /
• pp.257-265
• /
• 2020

Densities (ρ) for binary mixtures of ethanol (1) + diisopropyl ether (DIPE) or cyclohexane or alkane (C₆-C₉) (2) were measured at 298.15 K, 308.15 K and 318.15 K. The excess molar volume (V^E_m) of binary mixtures was calculated using ρ data and correlated with Redlich-Kister polynomial equation. The V^E_m values for binary mixtures of ethanol (1) + cyclohexane or n-alkane (C₆-C₉) (2) were positive, whereas for ethanol (1) + DIPE (2) these were negative. The magnitude of V^E_m values follows the order: cyclohexane > n-nonane > n-octane > n-heptane > n-hexane > DIPE. The V^E_m values have been interpreted qualitatively and also quantitatively in terms of Flory-Treszczanowicz-Benson (FTB) model and Prigogine-Flory-Patterson (PFP) theory. The values V^E_m predicted using FTB model agree well with experimental V^E_m values at all mole fractions. But the PFP theory describes well V^E_m data in ethanol-rich region (x₁ > 0.5) for all binary mixtures and is able to predict the sign of V^E_m vs x₁ curve for ethanol-lean region (x₁ < 0.5) except for ethanol (1) + nonane (2) mixtures.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.12
• /
• pp.2913-2917
• /
• 2009

Second-order rate constants (k$_{Nu–}$) have been measured for nucleophilic substitution reactions of Y-substituted phenyl benzoates (1a-i) with butane-2,3-dione monoximate ($Ox^-\;an\;\alpha$-nucleophile) and Z-substituted phenoxides in 80 mol% H$_2$O/20 mol% DMSO at 25.0${\pm}$0.1$^{\circ}C$. Hammett plots correlated with ${\sigma}^o$ and ${\sigma}^-$ constants for reactions of 1a-h with Ox$^–$ exhibit many scattered points. In contrast, the Yukawa-Tsuno plot results in a good linear correlation with ${\rho}_Y$ = 2.20 and r = 0.45, indicating that expulsion of the leaving group occurs in the rate-determining step (RDS). A stepwise mechanism with expulsion of the leaving-group being the RDS has been excluded, since Y-substituted phenoxides are less basic and better nucleofuges than Ox$^–$. Thus, the reactions have been concluded to proceed through a concerted mechanism. Ox$^–$ is over 10$^2$ times more reactive than its reference nucleophile, 4-chlorophenoxide (4-ClPhO$^–$). One might suggest that stabilization of the transition-state (TS) through intramolecular general acid/base catalysis is responsible for the ${\alpha}$-effect since such general acid/base catalysis is not possible for the corresponding reactions with 4-ClPhO$^–$. However, destabilization of the ground-state (GS) of Ox$^–$ has been concluded to be mainly responsible for the ${\alpha}$-effect found in this study on the basis of the fact that the magnitude of the ${\alpha}$-effect is independent of the nature of the substituent Y.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.4
• /
• pp.363-368
• /
• 2016

In this study, we numerically analyze fatigue cracks of curved pipes under cyclic loadings. Numerical models of the curved pipes are developed. The models are verified with the experimental results in terms of fatigue lives and development process of the fatigue cracks. Erosion technique is applied to the solid elements in order to describe shapes of the fatigue cracks and estimate the fatigue lives. Also, development of the fatigue cracks is described by allocating sufficient number of solid elements in the radial direction. Fatigue lives and shapes of the crack resulting from numerical analyses show good agreement with those of the experiment considering ${\pm}100mm$ displacement. In addition, estimation of the fatigue life caused by displacement with different magnitude is conducted. We expect that the model can be applied to understand the relation between fatigue lives and characteristics of pipes or loadings.