• 한국표면공학회지
• /
• 제55권6호
• /
• pp.363-367
• /
• 2022

Transparent ZnO/Ti/ZnO (ZTZ) tri-layered films were prepared with radio frequency (RF) and direct current (DC) magnetron sputtering on the glass substrate. The thickness of the ZnO and Ti films was kept at 50 and 10 nm to consider the effect of the electron irradiation on the crystallization and optoelectrical properties of the films. From the XRD spectra, post-depostion electron irradiated films showed the characteristic peaks of ZnO(002) and Ti(200), respectively. the observed grain size of the ZnO(002) and Ti(200) enlarged up to 18.27 and 12.16 nm at an irradiation condition of 750 eV. In the figure of merit which means an optoelectrical performance of the films, as deposited films show a figure of merit of 2.0×10^-5 𝛺^-1, while the films electron irradiated at 750 eV show a higher figure of merit of 5.7×10^-5 𝛺^-1.

• 센서학회지
• /
• 제13권4호
• /
• pp.277-281
• /
• 2004

$Hg_{1-x}Cd_{x}Te$ (MCT) was grown by hot wall epitaxy. Prior to the MCT growth, the CdTe (111) buffer layer was grown on the GaAs substrate at the temperature of $590^{\circ}C$ for 15 min. When the thickness of the CdTe buffer layer was $5{\mu}m$ or thicker, the full width at half maximum values obtained from the x-ray rocking curves were found to significantly decrease. After a good quality CdTe buffer layer was grown, the MCT epilayers were grown on the CdTe (111)/GaAs substrate at various temperatures in situ. The crystal quality for those epilayers was investigated by means of the x-ray rocking curves and the photocurrent experiment. The photoconductor characterization for the epilayers was also measured. The energy band gap of MCT was determined from the photocurrent measurement and the x composition rates from the temperature dependence of the energy band gap were turned out.

• 열처리공학회지
• /
• 제29권2호
• /
• pp.62-65
• /
• 2016

TIO thin films were deposited on the poly-carbonate substrates with RF magnetron sputtering under different sputtering power condition to investigate the influence of deposition rate on the electrical and optical properties of the films. Although, all films have the similar carrier concentration, the films prepared at a lower deposition rate of 4 nm/min show a higher mobility of $5.96cm^2\;V^{-1}S^{-1}$ due to the low surface roughness. In addition, optical transmittance is also influenced by a deposition rate. Based on the figure of merit, it can be concluded that the lower deposition rate effectively enhances the opto-electrical performance of IGZO films for use as transparent conducting oxides in flexible display applications.

• 전기학회논문지
• /
• 제59권1호
• /
• pp.123-126
• /
• 2010

$Cu_2O$ nanoparticles-based films are fabricated by spin-coating on glass substrates and their optoelectronic characteristics are investigated in this study. The $Cu_2O$ films are nearly all-transparent as high as 98% in a wavelength range from 400 nm to 900 nm and three exciton peaks associated with the sublevels in the conduction band are observed at the wavelengths shorter than 400 nm in the absorption spectrum. Under the illumination of the 325 nm wavelength light, the photocurrent efficiency of the $Cu_2O$ film is $1.8\times10^5 {\mu}A/W$ at a voltage of 2.5 V in air.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1599_1600
• /
• 2009

ZnS:Mn 나노입자가 포함된 PVP 고분자 하이브리드 나노사를 전기방사법으로 제작하였다. 하이브리드 나노사의 표면 특성은 주사 전자 현미경으로 관측하였으며, 형광분광광도계와 공초점 주사현미경 (CLSM)을 이용하여 하이브리드 나노사의 발광특성을 조사하였다. 순수한 PVP 나노사와 하이브리드 나노사의 photoluminescence (PL) 스펙트럼 비교를 통하여, 586 nm에서 관찰된 PL 피크는 ZnS:Mn 나노입자에서 기인되었음을 알 수 있었으며, CLSM을 이용하여 ZnS:Mn 나노입자의 발광을 이미지화 하였다.

• 열처리공학회지
• /
• 제24권4호
• /
• pp.199-202
• /
• 2011

Ga doped ZnO thin films were deposited with RF magnetron sputtering on glass substrate without intentional substrate heating and then the effect of post deposition annealing temperature on the structural, optical and electrical properties of the films was investigated. The post deposition annealing process was conducted for 30 minutes in a vacuum of $1{\times}10^{-3}$ Torr and the vacuum annealing temperatures were 150 and $300^{\circ}C$, respectively. As increase annealing temperature, GZO films show the increment of the prefer orientation of ZnO (002) diffraction peak in the XRD pattern and the optical transmittance in a visible wave region was also increased, while the electrical sheet resistance was decreased. The figure of merit obtained in this study means that GZO films which vacuum annealed at $300^{\circ}C$ have the highest optoelectrical performance in this study.

• 열처리공학회지
• /
• 제27권5호
• /
• pp.225-229
• /
• 2014

The influence of electron irradiation energy(eV) on the structural, electrical and optical properties of ITO/ZnO bi-layered films prepared with RF magnetron sputtering has been investigated. The ITO/ZnO show the lowest resistivity of $2.8{\times}10^{-4}{\Omega}cm$. The optical transmittance in a visible wave length region also increased with the electron irradiation energy. The film irradiated at 900 eV shows 82---- of optical transmittance in this study. By comparison of figure of merit, it was observed the optical transmittance and electrical resistivity of the films were dependent on the electron irradiation energy and optoelectrical performance of ITO/ZnO film is improved with electron irradiation.

• 한국세라믹학회지
• /
• 제55권4호
• /
• pp.325-336
• /
• 2018

Perovskite solar cells (PSCs) are a new class of photovoltaic devices, which have attracted significant attention due to their remarkable optoelectrical properties, including high absorption coefficients, high carrier mobilities, long carrier diffusion lengths, tunable bandgaps, low cost, and facile fabrication. PSCs have reached efficiencies of 22.70% and 18.36% on rigid fluorine-doped tin oxide and poly(ethylene terephthalate) substrates, respectively; these are comparable to those of single-crystal silicon and copper-indium-gallium-selenium solar cells. Over the past eight years, the photo conversion efficiency of PSCs has been significantly improved by device-architecture adjustments, and absorber and electron/hole transport layer optimization. Each layer is important for the performance of PSCs; hence, we discuss achievements in flexible perovskite solar cells (FPSCs), covering electron/hole-transport materials, electrode materials. We give a comprehensive overview of FPSCs and put forward suggestions for their further development.

• 한국전기전자재료학회논문지
• /
• 제36권4호
• /
• pp.326-331
• /
• 2023

The utilization of scanning transmission electron microscopy (STEM) in conjunction with cathodoluminescence (CL) has emerged as a valuable tool for the investigation of material optical properties. In recent years, this technique has facilitated significant advancements in the fields of plasmonics and quantum emitters by surpassing prior technical restrictions. The review commences by providing an outline of the diverse STEM-CL operating modes and technical aspects of the instrumentation. The review explains the fundamental physics of light production under electron beam irradiation and the physical basis for interpreting STEM-CL experiments for different types of excitations. Additionally, the review compares STEM-CL to other related techniques such as scanning electron microscope CL, photoluminescence, and electron energy-loss spectroscopy.

• 한국세라믹학회지
• /
• 제39권2호
• /
• pp.120-125
• /
• 2002

AC powder EL 소자를 절연층의 유전재료와 후면전극의 전기비저항을 변화시켜 스크린 프린팅법으로 제조하였다. 제조된 소자의 광전기적 특성을 평가하기 위하여 인가 전압은 50∼300 $V_{rms}$까지 변화시켜 휘도 및 전류밀도를 측정하였다. 주파수 및 전압공급원은 정현파 발생 장치로서 frequency generator를 이용하였다. 휘도는 luminometer 의해 측정되었으며 전류밀도 측정을 위하여 multimeter를 사용하였다. 또한 유전층에 대한 유전율을 후막 제조 후 impedance analyser(HP 4194 A)를 이용하여 측정하였다. $TiO_2$ 분말을 $BaTiO_3$에 첨가함에 따라 유전율의 향상으로 초저가형 AC powder EL 소자의 유전층에 적용함으로써 거의 비슷한 전류밀도 하에 50 cd/$m^2$ 정도의 향상된 휘도를 얻을 수 있었다. 저전력 소모형 AC powder EL 소자의 유전층에 적용시 상용분말을 이용한 경우보다 용액 연소법에 의해 제조된 $BaTiO_3$ 분말을 이용한 경우가 더욱 향상된 85 cd/$m^2$ 정도의 휘도를 얻을 수 있었다. 또한 후면전극의 전기 비저항을 조절함으로써 AC powder EL 소자의 휘도는 비교적 감소하지만 전류밀도를 낮출 수 있었다.