• Journal of Environmental Health Sciences
• /
• v.32 no.5 s.92
• /
• pp.446-450
• /
• 2006

In order to treat the wastewater containing organic compound, pre-treatment system connected with MSP(molecular separation process) was investigated. With the aim of selecting an optimum process of Fenton's oxidation, removal efficiency of each process in the optimum reaction condition was recommended. The $Fe/H_{2}O_{2}$(ferric sulfate to hydrogen peroxide)reagent is referred to as the Fenton's regent, which produces hydroxyl radicals by the interaction of Fe with $H_{2}O_{2}$. The powerful oxidizing ability and extreme kinetic reactively of the hydroxyl radical was well established. Increasing dosage of $Fe/H_{2}O_{2}$ increased removal efficiency as molar ratio of $Fe/H_{2}O_{2}$ between 0.2 and 2.5. Optimum dosage of molar ratio was 1. The removal efficiency for reaction condition was increased as pH decreased when the molar ratio of $Fe/H_{2}O_{2}$ was 1.7. Fenton's oxidation was most efficient in the reaction time 35 min for complex wastewater. Also, coagulation aid experiments using kaolin resulted in 3% of kaolin dosage.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.5
• /
• pp.905-910
• /
• 2004

This study was carried out to observe the change of oriental melon juice quality during manufacture by heating condition and enzyme treatment. To use over-production oriental melon effectively, oriental melon juice was prepared with change of heating temperature and heating time. The heating conditions for minimum filtration time were 98.57$^{\circ}C$ and 11.29 min. The optimum conditions Predicted for separation ratio of clear solution, filtration time and browning color intensity of oriental melon juice were 98$^{\circ}C$, 13 min. In the pectin-degrading enzyme treatment test, turbidity showed minimum value in 4.40 mg％(pectin-degrading enzyme content)， 39.72 mg％ (gelatin content) and 24.09 min (treatment time)．Browning color intensity showed minimum value in 9.33 mg％ (pectin-degrading enzyme content)，44.70 mg％ (gelatin content) and 115.56 min (treatment time). The optimum conditions predicted for turbidity and browning color intensity of oriental melon concentration Juice were 6.6 mg％ (pectin-degrading enzyme content), 33.6 mg％ (gelatin content) and 70 min (treatment time).

• KSBB Journal
• /
• v.6 no.4
• /
• pp.351-361
• /
• 1991

This study is on the investigation of hydrogen production and substrate removal by photosynthetic bacteria. After using of Rhodospillum rubrum KS-301 and IFO 3986, which are photosynthetic bacteria as strains, R. rubrum KS-301 was turned out a better strain. And result of experiment in which glucose and sodium lactate, components of wastewater, were used limiting substrates, showed that the productivity of hydrogen was indifferent with the kind of substrates. In batch experiments using free cells and immobilized whole cells, the decrease in hydrogen productivity was observed in the latter case. From the results of these experiments, specific growth rate of cells, specific utilization rate of glucose, and specific production rate of hydrogen were calculated. And each rate was expressed in the form of Monod equation of which parameters were estimated. Also the optimum condition of hydrogen production for free cells was $30^{\circ}C$, pH 7, and 12,000 Lux, and the optimum immobilized condition was as follows: initial immobilized cell concentration 1.0g/L, sodium alginate concentration 2% and light intensity 12,000 Lux.

• Asian Journal of Turfgrass Science
• /
• v.9 no.3
• /
• pp.253-260
• /
• 1995

This study is aimed to understand the effects of temperature, light and GA soaking treatment on the seed germination of perennial ryegrass 'Dandy', creeping hentgrass 'Penlinks', tall fescue 'Arid' and Kentucky hluegrass 'Nasaw'. These experiments are carried in vitro, and their results obtained are summarized as the followings ; The optimum temperature for seed germination of perennial ryegrass 'Dandy' was found to he ranged at 20~30$^{\circ}C$, and the optimum temperature for germination of creeping bentgrass 'Penlinks', tall fescue 'Arid' and kentucky bluegrass 'Nasaw' seeds was found to be ranged at 20~25$^{\circ}C$, whereas the germination percentage under the below or above temperature of this range decreased. The germination of perennial ryegrass 'Dandy' and tall fescue 'Arid' seeds showed no effect on light, and while the germination percentage of creeping hentgrass 'Penlinks' increased more highly under the dark condition than under the light condition. The germination percentage decreased according to the higher temperature. The germination of Kentucky bluegrass 'Nasaw' seeds increased more highly under the dark condition than under the light condition at 20~25$^{\circ}C$, whereas the germination percentage under the dark condition at 15$^{\circ}C$ and 30$^{\circ}C$ decreased. In case of GA soaking treatment of seeds, all the cool season turfgrasses tested showed their own promoting effects on seed germination. The early germination of tall fescue 'Arid' was good without the soaking times. Creeping bentgrass 'Penlinks' and perennial ryegrass 'Dandy' had re-spectively the highest germination percentage at 10min and 1hr soaking treatment, and the longer the soaking time, the lesser the germination percentage. Kentucky bluegrass 'Nasaw' obtained the best results at 24has soaking treatment, and the longer the soaking time, the better the ger-mination percentage.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.1
• /
• pp.46-53
• /
• 1998

The variation of the mechanical properties, microstructures and the formation of retained austenite with heat treatment conditions in austempered ductile cast iron has been investigated. In the case of austempered ductile cast iron below 25mm diameter, it has been found that a pearlite structure are not obtained under a super cooled condition at range of $0.05^{\circ}C/sec{\sim}10^{\circ}C/sec$, and the matrix is precipitated in graphite, bainite and retained austenite. After austempering treatment the retained austenite is increased with decreasing cooling rate. The elongation increases with decreasing super cooling rate, and the optimum result has been shown to be the elongation of 15.6% at super cooling rate of $0.05^{\circ}C/sec$. The optimum result has been shown to be the tensile strength-elongation balance of $1656kgf/mm^2.%$ and it is more than doubled to as the casting state and continuous cooling condition.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.2
• /
• pp.33-38
• /
• 2013

In the past, a very popular method for reducing the corrosion on zinc involved the use of chemical conversion layer coatings based on $Cr^{+6}$. However, there is an important problem with using chromium salts as a result of restrictive environmental protection legislation. This study investigated the optimum condition for galvanized steel using an organic/inorganic solution with a Ti composition. In the case of a fixed heat treatment time, the corrosion resistance values of LR-0727(1) and LR-0727(2) were improved as the heat treatment temperature increased, and the optimum minimum temperature decreased with the heat treatment time. At the optimum heat treatment condition of two coating solutions, the heat treatment time of the LR-0727(1) solution was shorter than LR-0727(2) for the same heat treatment temperature. LR-0727(1) coated specimens did not show desquamation, and all of the specimens showed a good adhesive property. In contrast, in the case of the LR-0727(2) coated specimens, desquamation arose. Therefore, the adhesive property of LR-0727(1) was superior to that of LR-0727(2). The pencil hardness had a 3H average for all of the coating solutions and heat treatment conditions. In the case of a corrosion resistance test with boiling water, the coated specimens of LR-0727(1) were discolored, but LR-0727(2) was not. Finally, LR-0727(1) was more moisture proof than LR-0727(2).

• Textile Coloration and Finishing
• /
• v.18 no.3 s.88
• /
• pp.31-41
• /
• 2006

Functional properties are available with sputtering. But sputtering treatment alone cannot got a good fastness performance to washing, rubbing and light. This research was objected to investigate optimum condition by sputtering on polyester through various processing conditions such as ion current and treatment time, and then various resin treated onto metal coated polyester fabrics in order to increase washing fastness of metal membrane. As the results, the optimum conditions revealed 1500 mA of ion current, 2 min of treatment time in sputter, and suitable resin concentrations were 2% of o.w.s (on the weight of solution) in resin treatment. Therefore, we could get enhanced anti-static effect and flex stiffness as well as washing fastness in sputtered polyester fabric with various resin treatment, for example, melamine and polyurethane.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.32 no.9
• /
• pp.1461-1466
• /
• 2008

This study provides effects of mixed activators on enzymatic activation and determines optimum mixture ratio for enzymatic treatment. Wool 80% and polyester 20% blend fabric and papain from carica papaya are used in this experiment. L-cysteine and sodium sulfite are used as activators for papain treatment process. The treatment condition is pH 7.5, $70^{\circ}$, papain concentration 10%(o.w.f), 60 minutes. L-cysteine and sodium sulfite are added in enzyme solution with various concentrations($0{\sim}50mM$). The optimum treatment condition is determined by measuring weight loss, tensile strength, whiteness, water contact angle(WCA), dyeability and surface micrographs. The results are as follow; The optimum mixture ratio of activators is L-cysteine 2mM and sodium sulfite 10mM. Mixed activators assists in improving the activation of papain. WCA of papain treated fabrics is decreased since papain treatment with activator mixture makes wool polyester blend fabrics more hydrophilic. Dyeing property of papain-treated fabrics more improves by the treatment with mixed activators than with single activator. It means that this method can save time and lower cost. After papain treatment in the presence of mixed activator, the surface of fabrics is modified. The surface of wool fiber shows to be descaled and hydrolyzed, and that of polyester fiber shows to be cracked.

• Textile Coloration and Finishing
• /
• v.4 no.4
• /
• pp.97-103
• /
• 1992

For manufacturing a high sorptive ACF, we used orthognal array experimental design to get optimum condition. The ability of ACF was measured by $CCl_4$ adsorption and showed those manufacturing conditions were effective in the order of treatment time>oxidative gas>treatment temperature. The optimal condition presented the maximum adsorption rate was at 90$0^{\circ}C$ for 6 minutes with $CO_2$/$H_2O$ gas in the PAN based ACF manufacturing process. The adsorption rate of developed ACF in this experiment was over 100%.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.51 no.1
• /
• pp.94-101
• /
• 2015

The heat treatment machine based on immersion was developed to reduce temperature difference during netting process and appraised it performance compared current heat treatment machine using high pressure. It was also reviewed the optimum heat treatment procedures for PBSAT monofilament net in accordance with the immersion time and temperature. The procedure was based on physical measurement such as breaking load, elongation and angle of the mesh for PBSAT monofilament. The water temperature gap of the treatment machine based on immersion was less than $1^{\circ}C$. and the energy consumption was also increased in high temperature condition. It was identified that the optimum temperature was $75^{\circ}C$ and its optimum processing time was between 15 minutes and 20 minutes to get qualified physical properties.