• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1995.10a
• /
• pp.9-16
• /
• 1995

This study presents the applicable possibility of numerical optimization and Genetic Algorithm in the design of truss structures using discrete variables and real constraints. The introduction of Genetic Algorithm in the design of truss structures enables us to do easier formulation and handle discrete variables. To investigate these applicable possibility, the design of 15 - bar truss structures has been studied using GT/STRUDL and Genetic Algorithm and the results of Genetic Algorithm are compared with GT/STRUDL's.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.1
• /
• pp.135-142
• /
• 2008

This study is concerned with the optimum design of LB-Deck plate girder bridge. The optimizing problems of the composite bridge are formulated with objective functions and constraints. The objective functions are formulated as the total cost of the concrete deck and steel girder construction and the constraints are derived by criteria with respect to the Korean Highway bridge design. The optimizing algorithm using SUMT for optimum design of the Simple span, 2-Span, 3-span LB-deck plate and general RC-steel composite girder bridges (L=60m) which act live load(DB24). And their optimum numerical results are compares and analyzed to examine the possibility of optimization, the application and convergency of this optimizing algorithm.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.3
• /
• pp.159-167
• /
• 2004

The objective of this study is development of the optimum design program to minimize the cost for PSC box girder bridge using the full staging method to indicate the necessity for the optimum design applied many types of bridges. It also considered the proper span length to girder depth ratio and the cell number along the width of bridge. This program used SUMT procedure and Kavlie's extended penalty function to allow infeasible design points in the process. Powell's direct method was used in searching design points and Gradient Approximate Method was used to reduce design hours. This study showed the convergence in design parameter and correlation of totally optimized cost according to cell numbers, span lengths, and lane numbers.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.3
• /
• pp.89-97
• /
• 1997

A genetic algorithm (GA) is a stochastic direct search strategy that mimics the process of genetic evolution. The GA applied herein works on a population of structural designs at any one time, and uses a structured information exchange based on the principles of natural selection and wurvival of the fittest to recombine the most desirable features of the designs over a sequence of generations until the process converges to a "maximum fitness" design. Principles of genetics are adapted into a search procedure for structural optimization. The methods consist of three genetics operations mainly named selection, cross- over and mutation. In this study, a method of finding the optimum topology of truss/beam structure is pro- posed by using the GA. In order to use GA in the optimum topology problem, chromosomes to FEM elements are assigned, and a penalty function is used to include constraints into fitness function. The results show that the GA has the potential to be an effective tool for the optimal design of structures accounting for sizing, geometrical and topological variables.variables.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.5
• /
• pp.143-151
• /
• 2008

In this paper, the optimum design of plane steel frames using second-order inelastic analysis and section increment method is presented. Since the second-order inelastic analysis accounts for geometric and material nonlinearities of the whole system as well as its component members, the design method based on second-order inelastic analysis does not require separate member capacity checks after analysis. A section increment method proposed by this paper is used as optimization technique. The weight of structures is treated as the objective function. The constraint functions are defined by load-carrying capacities, deflections, inter-story drifts, and ductility requirement. The effectiveness of the proposed method are verified by comparing the results of the proposed method with those of other method.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.14 no.3
• /
• pp.267-276
• /
• 2001

On the basis of structural analysis of the radial gate(that is, Tainter gate), this paper focuses on the optimization of the moment distribution according to the location of the arm of the radial gate. In spite of its importance from economical view point, we could hardly find the study on the optimum design of radial gate. Accordingly, the present study identifies the optimum section modulus for a radial arm along with the optimum position for 2 of 3 radial arms with a convex cylindrical skin plate relative to a given radius of the skin plate curvature, pivot point, water depth, ice pressure, etc. These optimum measurements are then compared with previously constructed radial gates. The results indicate that the optimum section modulus vague for a radial arm was appreciably smaller than the previously constructed examples.

• Structural Engineering and Mechanics
• /
• v.45 no.1
• /
• pp.111-127
• /
• 2013

In this paper, a new version of gravitational search algorithm based on opposition-based learning (OBGSA) is introduced and applied for optimum design of reinforced concrete retaining walls. The new algorithm employs the opposition-based learning concept to generate initial population and updating agents' position during the optimization process. This algorithm is applied to minimize three objective functions include weight, cost and $CO_2$ emissions of retaining structure subjected to geotechnical and structural requirements. The optimization problem involves five geometric variables and three variables for reinforcement setups. The performance comparison of the new OBGSA and classical GSA algorithms on a suite of five well-known benchmark functions illustrate a faster convergence speed and better search ability of OBGSA for numerical optimization. In addition, the reliability and efficiency of the proposed algorithm for optimization of retaining structures are investigated by considering two design examples of retaining walls. The numerical experiments demonstrate that the new algorithm has high viability, accuracy and stability and significantly outperforms the original algorithm and some other methods in the literature.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.1
• /
• pp.190-196
• /
• 2009

This study proposes a structural design method for the upper control arm installed at the rear side of a SUV. The weight of control arm can be reduced by applying the design and material technologies. In this research, the former includes optimization technology, and the latter the technologies for selecting aluminum as a steel-substitute material. Strength assessment is the most important design criterion in the structural design of a control arm. At the proto design stage of a new control arm, FE (finite element) analysis is often utilized to predict its strength. This study considers the static strength in the optimization process. The inertia relief method for FE analysis is utilized to simulate the static loading conditions. According to the classification of structural optimization, the structural design of a control arm is included in the category of shape optimization. In this study, the kriging interpolation method is adopted to obtain the minimum weight satisfying the strength constraint. Optimum designs are obtained by ANSYS WORKBENCH and the in-house program, EXCEL-kriging program. The optimum results determined from the in-house program are compared with those of ANSYS WORKBENCH.

• Computational Structural Engineering
• /
• v.5 no.3
• /
• pp.56-62
• /
• 1992

여기서 소개하게 될 MIDAS(the Most Intelletive Design and Analysis System) Package는 기존 구조해석 S/W Package들의 사용상 불편하였던 제반 문제점을 해소하고, 단시간내에 단위구조해석 및 설계작업이 가능하도록 개발되었으며, 특히 최신의 Computer Graphics 기능을 도입하여 모든 Data의 입력과정과 해석결과 Data 처리과정을 Graphic 화면상에서 직접 처리할 수 있도록 전처리 및 후처리 기능에 중점을 두고 개발함으로써 해석 실무자라면 누구든지 쉽게 사용이 가능하도록 하였다. MIDAS는 '90 중반 개발에 착수하여 '91.9 Version 1.0을 완료하였으며, '91.10 과학기술처에 공식등록하고 현재 Structural Optimum Design 및 설계도면 자동생산 기능 등을 포함한 Version 2.0을 개발 중에 있다.

• Journal of Korean Association for Spatial Structures
• /
• v.1 no.2 s.2
• /
• pp.59-66
• /
• 2001

This paper describes three modules for development of the Space Frame Integrated Design System(SFIDS). The Control Module is implemented to control the developed system. The Model Generation Module based on PATRAN user interface enables users to generate a complicated finite element model for space frame structures. The Optimum Design Module base on a branch of combinatorial optimization techniques which can realize the optimization of a structure having a large number of members designs optimum members of a space frame after evaluating analysis results. The Control Module and the Model Generation Module Is implemented by PATRAN Command Language(PCL) while C++ language is used in the Optimum Design Module. The core of the system is PATRAN database, in which the Model Generation Module creates information of a finite element model. Then, PATRAN creates Input files needed for the analysis program from the information of the finite element model in the database, and in turn, imports output results of analysis program to the database. Finally, the Optimum Design Module processes member grouping of a space frame based on the output results, and performs optimal member selection of a space frame. This process is repeated until the desired optimum structural members are obtained.