• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.5
• /
• pp.563-572
• /
• 2006

In order to propose optimum in-situ treatment for reducing phosphorous release from sediment of stationary lakes, a series of column tests were performed. The sediment used in experiment was very fine clay with a mean grain site $7.7{\phi}$ and high $C_{org}$ contents(2.4%). Phosphorous releases were evaluated in two ways : in lake water(with microbial effect) and in distilled water(without microbial effect). As in-situ capping material, sand and loess were used while Fe-Gypsum and $SiO_2$-Gypsum were used for in-situ chemical treatment. In case of lake water considering the effect of microorganism, phosphorous concentration rapidly decreased in the early stage of experiment but it was gradually increased after 10 days. Flux of phosphorous release for control was $3.0mg/m^2{\cdot}d$. Whereas, those for sand layer capping(5 cm) and loess layer capping(5 cm) were $2.5mg/m^2{\cdot}d\;and\;1.8mg/m^2{\cdot}d$, respectively because the latter two were not consolidated sufficiently. For Fe-gypsum and $SiO_2$-gypsum the fluxes were $1.4mg/m^2{\cdot}d$ which meant that reduction efficiency of phosphorous release was more than 40% higher than that of control. The case capping with complex layer was $1.0mg/m^2{\cdot}d$, which showed high reduction efficiency over 60%. The addition of gypsum($CaSO_4{\cdot}2H_2O$) into the sediment reduced release of Phosphorus from the sediments. Gypsum acted as a slow-releasing source of sulphate in sediment, which enhanced the activity of SRB(sulfate reducing bacteria) and improved the overall mineralization rate of organic matter.

• Journal of the Korean Institute of Gas
• /
• v.24 no.2
• /
• pp.1-8
• /
• 2020

Centrifugal pump is a facility that transfers energy to fluid through centrifugal force, which is usually generated by rotating the impeller at high speed, and is a major process facility used in many LNG production bases such as vaporization seawater pump, industrial water and fire extinguishing pump using seawater. to be. Currently, pumps in LNG plant sites are subject to operating conditions that vary depending on the amount of supply desired by the customer for a long period of time. Pumps in particular occupy a large part of the consumption strategy at the plant site, and if the optimum operation condition is not available, it can incur enormous energy loss in long term plant operation. In order to solve this problem, it is necessary to identify the performance deterioration factor through the flow analysis and the result analysis according to the fluctuations of the pump's operating conditions and to determine the optimal operation efficiency. In order to evaluate operation efficiency through experimental techniques, considerable time and cost are incurred, such as on-site operating conditions and manufacturing of experimental equipment. If the performance of the pump is not suitable for the site, and the performance of the pump needs to be reduced, a method of changing the rotation speed or using a special liquid containing high viscosity or solids is used. Especially, in order to prevent disruptions in the operation of LNG production bases, a technology is required to satisfy the required performance conditions by processing the existing impeller of the pump within a short time. Therefore, in this study, the rotation difference of the pump was applied to the ANSYS CFX program by applying the modified 3D modeling shape. In addition, the results obtained from the flow analysis and the curve fitting toolbox of the MATLAB program were analyzed numerically to verify the outer diameter correction theory.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.27 no.7
• /
• pp.380-394
• /
• 2015

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2014. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) The research works on the thermal and fluid engineering have been reviewed as groups of heat and mass transfer, cooling and heating, and air-conditioning, the flow inside building rooms, and smoke control on fire. Research issues dealing with duct and pipe were reduced, but flows inside building rooms, and smoke controls were newly added in thermal and fluid engineering research area. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer and industrial heat exchangers. Researches on heat transfer characteristics included the results for thermal contact resistance measurement of metal interface, a fan coil with an oval-type heat exchanger, fouling characteristics of plate heat exchangers, effect of rib pitch in a two wall divergent channel, semi-empirical analysis in vertical mesoscale tubes, an integrated drying machine, microscale surface wrinkles, brazed plate heat exchangers, numerical analysis in printed circuit heat exchanger. In the area of pool boiling and condensing, non-uniform air flow, PCM applied thermal storage wall system, a new wavy cylindrical shape capsule, and HFC32/HFC152a mixtures on enhanced tubes, were actively studied. In the area of industrial heat exchangers, researches on solar water storage tank, effective design on the inserting part of refrigerator door gasket, impact of different boundary conditions in generating g-function, various construction of SCW type ground heat exchanger and a heat pump for closed cooling water heat recovery were performed. (3) In the field of refrigeration, various studies were carried out in the categories of refrigeration cycle, alternative refrigeration and modelling and controls including energy recoveries from industrial boilers and vehicles, improvement of dehumidification systems, novel defrost systems, fault diagnosis and optimum controls for heat pump systems. It is particularly notable that a substantial number of studies were dedicated for the development of air-conditioning and power recovery systems for electric vehicles in this year. (4) In building mechanical system research fields, seventeen studies were reported for achieving effective design of the mechanical systems, and also for maximizing the energy efficiency of buildings. The topics of the studies included energy performance, HVAC system, ventilation, and renewable energies, piping in the buildings. Proposed designs, performance performance tests using numerical methods and experiments provide useful information and key data which can improve the energy efficiency of the buildings. (5) The field of architectural environment was mostly focused on indoor environment and building energy. The main researches of indoor environment were related to the evaluation of work noise in tunnel construction and the simulation and development of a light-shelf system. The subjects of building energy were worked on the energy saving of office building applied with window blind and phase change material(PCM), a method of existing building energy simulation using energy audit data, the estimation of thermal consumption unit of apartment building and its case studies, dynamic window performance, a writing method of energy consumption report and energy estimation of apartment building using district heating system. The remained studies were related to the improvement of architectural engineering education system for plant engineering industry, estimating cooling and heating degree days for variable base temperature, a prediction method of underground temperature, the comfort control algorithm of car air conditioner, the smoke control performance evaluation of high-rise building, evaluation of thermal energy systems of bio safety laboratory and a development of measuring device of solar heat gain coefficient of fenestration system.

• Journal of Aquaculture
• /
• v.21 no.1
• /
• pp.26-33
• /
• 2008

This study investigated the synergistic effects of dietary supplementation of quartz porphyry(QP) and a laboratory developed feed stimulants, BAISM(BS) on growth performance and utilization as the additives for juvenile eel Anguilla japonica. Six isoenergetic experimental diets(18.2 kJ/g) were formulated to contain 50% crude protein, 15% lipid with or without dietary QP(Song-Gang stone, Davistone, Korea) and BS supplementation. QP and BS were provided at 0% in the control diet($Q_0B_0$) and at 0.7% QP+0% BS($Q_{0.7}B_0$), 0.7% QP+0.3% BS($Q_{0.7}B_{0.3}$), 0.7% QP+0.5% BS($Q_{0.7}B_{0.5}$), 0.7% QP+0.75% BS($Q_{0.7}B_{0.75}$) and 0.7% QP+1.0% BS($Q_{0.7}B_{1.0}$) in experimental diets on dry matter basis. After four weeks of adaptation, triplicate groups of 30 fish initially averaging $15{\pm}0.1g(mean{\pm}SD)$ were randomly distributed into each aquarium, and they were fed one of the experimental diets for 8 weeks. By the end of the feeding trial, weight gain(%), specific growth rate(%), feed efficiency(%) and protein efficiency ratio of fish fed diet $Q_{0.7}B_{0.5},\;Q_{0.7}B_{0.75}\;and\;Q_{0.7}B_{1.0}$, were significantly higher(P<0.05) than those of fish fed the other diets. But, $Q_{0.7}B_{0.5},\;Q_{0.7}B_{0.75}\;and\;Q_{0.7}B_{1.0}$ were no significant differences(P<0.05). In challenge test, fish were infected by intraperitoneal injection of 0.1 mL bacterial suspension with Edwardsiella tarda per fish after the feeding trial. As a result, fish fed QP and BS supplemented diets have a significantly higher cumulative survival rate than those of fish fed control diet(P<0.05). In conclusion, these results indicated that the optimum dietary supplementation level of QP and BS could be approximately 0.7% quartz porphyry+0.5% BAISM($Q_{0.7}B_{0.5}$) of diet based on WG, FER, SGR, PER, cumulative survival rate in juvenile eel A. japonica.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.11
• /
• pp.1186-1191
• /
• 2006

Removal efficiency of As(III) through oxidation and adsorption in column reactors was investigated at different ratios of manganese-coated sand(MCS) and iron-coated sand(ICS) : MCS-alone, ICS-alone and both of ICS and MCS. The breakthrough of arsenic immediately occurred from a column reactor with MCS-alone. However, most of the arsenic present in the effluent was identified as As(V) due to the oxidation of As(III) by MCS. While five-times delayed breakthrough of arsenic was observed from a column reactor with ICS-alone. At a complete breakthrough of arsenic, the removed As(III) was 36.1 mg with 1 kg ICS. To find an optimum ratio of ICS and MCS in the column packed with both ICS and MCS, the removal efficiency of As(III) was investigated at three different ratios of ICS/MCS with a fixed amount of ICS. The breakthrough time of arsenic was quite similar in the different ratios ICS/MCS. However, much slower breakthrough of arsenic was observed as the ratio of ICS/MCS decreased. As the ratio of ICS/MCS decreased the concentration of As(III) in the effluent decreased and then showed below 50 ppb at an equal amount of ICS and MCS, suggesting more efficient oxidation of As(III) by greater amount of MCS. When a complete breakthrough of arsenic occurred, the removed total arsenic with an equal amount of ICS and MCS was 68.5 mg with 1 kg of filter material.

• Korean Journal of Soil Science and Fertilizer
• /
• v.44 no.6
• /
• pp.1071-1079
• /
• 2011

In this study, coal combustion ash (CCA) was evaluated for its stabilization effect on acidic mine waste with column experiment. Total of six treatments were installed depending on mixing ratio between coal wastes and CCA (0, 20, 40%) and mixing method (completely mixing and layered). Artificial acidic rain (pH 5.6) was used for feeding solution with flow rate of $0.05mL\;min^{-1}$. Result showed that higher pH of leachate was observed as more CCA was mixed. The highest pH in leachate was measured when 40% of CCA was mixed with coal waste (pH of 5.8). Also, complete mixing with CCA and coal waste was more effective to increase the pH of leachate than layered treatment. Regarding the reduction of soluble Fe amount, the highest efficiency (78%) was observed when 20% of coal ash was completely mixed with mine waste. Based on those result, optimum mixing ratio of coal ash with mine waste can be ranged 20-40% depending on environmental circumstances in the field.

• Korean Journal of Soil Science and Fertilizer
• /
• v.10 no.3
• /
• pp.103-134
• /
• 1977

The physiological and biochemical role of potassium for upland crops according to recent research reports and the nutritional status of potassium in Korea were reviewed. Since physical and chemical characteristics of potassium ion are different from those of sodium, potassium can not completely be replaced by sodium and replacement must be limited to minimum possible functional area. Specific roles of potassium seem to keep fine structure of biological membranes such as thylacoid membrane of chloroplast in the most efficient form and to be allosteric effector and conformation controller of various enzymes principally in carbohydrate and protein metabolism. Potassium is essential to improve the efficiency of phoro- and oxidative- phosphorylation and involve deeply in all energy required metabolisms especially synthesis of organic matter and their translocation. Potassium has many important, physiological functions such as maintenance of osmotic pressure and optimum hydration of cell colloids, consequently uptake and translocation of water resulting in higher water use efficiency and of better subcellular environment for various physiological and biochemical activities. Potassium affects uptake and translocation of mineral nutrients and quality of products. potassium itself in products may become a quality criteria due to potassium essentiality for human beings. Potassium uptake is greatly decreased by low temperature and controlled by unknown feed back mechanism of potassium in plants. Thus the luxury absorption should be reconsidered. Total potassium content of upland soil in Korea is about 3% but the exchangeable one is about 0.3 me/100g soil. All upland crops require much potassium probably due to freezing and cold weather and also due to wet damage and drought caused by uneven rainfall pattern. In barley, potassium should be high at just before freezing and just after thawing and move into grain from heading for higher yield. Use efficiency of potassium was 27% for barley and 58% in old uplands, 46% in newly opened hilly lands for soybean. Soybean plant showed potassium deficiency symptom in various fields especially in newly opened hilly lands. Potassium criteria for normal growth appear 2% $K_2O$ and 1.0 K/(Ca+Mg) (content ratio) at flower bud initiation stage for soybean. Potassium requirement in plant was high in carrot, egg plant, chinese cabbage, red pepper, raddish and tomato. Potassium content in leaves was significantly correlated with yield in chinese cabbage. Sweet potato. greatly absorbed potassium subsequently affected potassium nutrition of the following crop. In the case of potassium deficiency, root showed the greatest difference in potassium content from that of normal indicating that deficiency damages root first. Potatoes and corn showed much higher potassium content in comparison with calcium and magnesium. Forage crops from ranges showed relatively high potassium content which was significantly and positively correlated with nitrogen, phosphorus and calcium content. Percentage of orchards (apple, pear, peach, grape, and orange) insufficient in potassium ranged from 16 to 25. The leaves and soils from the good apple and pear orchards showed higher potassium content than those from the poor ones. Critical ratio of $K_2O/(CaO+MgO)$ in mulberry leaves to escape from winter death of branch tip was 0.95. In the multiple croping system, exchangeable potassium in soils after one crop was affected by the previous crops and potassium uptake seemed to be related with soil organic matter providing soil moisture and aeration. Thus, the long term and quantitative investigation of various forms of potassium including total one are needed in relation to soil, weather and croping system. Potassium uptake and efficiency may be increased by topdressing, deep placement, slow-releasing or granular fertilizer application with the consideration of rainfall pattern. In all researches for nutritional explanation including potassium of crop yield reasonable and practicable nutritional indices will most easily be obtained through multifactor analysis.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.15 no.3
• /
• pp.175-185
• /
• 1995

This experiment was carried out to investigate the optimum rates of animal excreta(cattle slurry-N) for the highest dry matter production and improve the nutritive values of reed canarygrass with different cutting frequency. The results are summarized as follows; The highest relative dry matter yields for annual dry matter yield were 42.2% and 45.2% at 3rd cut in 3 and 4 cuttings, and 34.7% at 4th cut in 5 cuttings, respectively. The annual dry matter yields of non slurry-N application plot showed were from 6.8 tons to 8.0 tons/ha in all cutting frequencies. The highest annual dry matter yield obtained was in 3 cuttings. The annual dry matter yield increased with an increase of applied rates of slurry-N in all cutting frequencies. Annual dry matter yield was produced by 3.3 tons/ha at rates of 90 kg N/ha/cut in 3 cuttings, and more 1.7 tonsha and 2.4 tons/ha at rates of 30 kg N/ha/cut in 4 and 5 cuttings than that of non slurry-N application plots. The contents of crude protein were 12.01% and 15.0% at rates of 90 kg N/ha/cut in 3 and 4 cuttings, and 16.59% at rates of 120 kg N/ha/cut in 5 cuttings, respectively. On the contrary, the content of acid detergent fibre(ADF) showed the lowest values at same rates of slurry-N application in each cutting. J. The average content of crude protein was significantly increased with cutting frequencies, and they were 11.43%, 13.53% and 15.53% in 3, 4 and 5 cuttings, respectively. The average contents of acid detergent fibre(ADF) were 40.27%, 40.53% and 37.06% in 3, 4 and 5 cuttings. The values of 5 cuttings were significantly lower than other cutting frequencies, but the values of acid detergent fibre(ADF) was not significantly different between 3 and 4 cuttings. 6. The efficiency of dry matter production to slurry-N application rates showed the highest values of 18.9 kg and 15.7 kg DM/kg N at rates of 30 kg N/ha/cut in 3 and 5 cuttings, and 16.3 kg DM/kg/ N at rates of 90 kg N/ ha/cut in 4 cuttings. The efficiency of total nitrogen yield to slurry-N application rates were the highest values of 0.51 kg and 0.43 kg W k g N at rates of 30 kg N/ha/cut in 4 and 5 cuttings, and 0.52 kg TN/kg N at rates of 90 kg N/ha/cut in 3 cuttings, respectively. 7. The ranges of economic slurry-N rates were estimated as the 107.2-151.0 kglha, 359.1-375.7 kgha and 160.3-236.9 kg/ha in 3, 4 and 5 cuttings, and marginal dry matter yields were 9.6-10.0 tons/ha, 12.4-12.6 tons/ha and 9.0-9.7 tons/ha in 3, 4 and 5 cuttings, respectively. 8. The limiting sluny-N application rates to maintain the highest dry matter yields were estimated to be 420.0 kg/ ha, 440.6 kg/ha and 666.3 kg/ha in 3, 4 and 5 cuttings.

• Journal of Animal Science and Technology
• /
• v.49 no.4
• /
• pp.459-470
• /
• 2007

Domestically, finishing pigs are marketed at 110 kg on an average. However, it is thought to be feasible to increase the market weight to 120kg or greater without decreasing the carcass quality, because most domestic pigs for pork production have descended from lean-type lineages. The present study was undertaken to investigate the growth efficiency and profitability of ‘high’-market wt pigs and the physicochemical characteristics and consumers' acceptability of the high-wt carcass. A total of 96 (Yorkshire × Landrace) × Duroc-crossbred gilts and barrows were fed a finisher diet ad laibtum in 16 pens beginning from 90-kg BW, after which the animals were slaughtered at 110kg (control) or ‘high’ market wt (135 and 125kg in gilts & barrows, respectively) and their carcasses were analyzed. Average daily gain and gain:feed did not differ between the two sex or market wt groups, whereas average daily feed intake was greater in the barrow and high market wt groups than in the gilt and 110-kg market wt groups, respectively(P<0.01). Backfat thickness of the high-market wt gilts and barrows corrected for 135 and 125-kg live wt, which were 23.7 and 22.5 mm, respectively, were greater (P<0.01) than their corresponding 110-kg counterparts(19.7 & 21.1 mm). Percentages of the trimmed primal cuts per total trimmed lean (w/w), except for that of loin, differed statistically (P<0.05) between two sex or market wt groups, but their numerical differences were rather small. Crude protein content of the loin was greater in the high vs. 110-kg market group (P<0.01), but crude fat and moisture contents and other physicochemical characteristics including the color of this primal cut were not different between the two sexes or market weights. Aroma, marbling and overall acceptability scores were greater in the high vs. 110-kg market wt group in sensory evaluation for fresh loin (P<0.01); however, overall acceptabilities for cooked loin, belly and ham were not different between the two market wt groups. Marginal profits of the 135- and 125-kg high-market wt gilt and barrow relative to their corresponding 110-kg ones were approximately -35,000 and 3,500 wons per head under the current carcass grading standard and price. However, if it had not been for the upper wt limits for the A- and B-grade carcasses, marginal profits of the high market wt gilt and barrow would have amounted to 22,000 and 11,000 wons per head, respectively. In summary, 120～125-kg market pigs are likely to meet the consumers' preference better than the 110-kg ones and also bring a profit equal to or slightly greater than that of the latter even under the current carcass grading standard. Moreover, if only the upper wt limits of the A- & B-grade carcasses were removed or increased to accommodate the high-wt carcass, the optimum market weights for the gilt and barrow would fall upon their target weights of the present study, i.e. 135 and 125 kg, respectively.

• Journal of Animal Science and Technology
• /
• v.45 no.6
• /
• pp.975-986
• /
• 2003

Present study was conducted to investigate the effect of the level of concentrates and pasture grazing in 36 autumn born Hanwoo heifers(initial body weight, 119.7${\pm}$25.6kg) for 426d including 195d for a pasture stage. The animals were fed commercial concentrates at a rate of 0.5%(T1), 1.0%(T2), 1.5%(T3) and 2.0%(T4) of body weight, respectively, for pre- and post-pasture. 1. Mean daily gains by treatments were 0.348, 0.403, 0.450 and 0.501kg for T1, T2, T3 and T4, respectively, indicating that increases in concentrates intake was associated with the daily gain of grazing Hanwoo heifers. However, the mean daily gain was the highest for T2 during the pasture stage. 2. TDN intakes per 1kg gain were, on average, 8.61kg for the entire experimental period and 9.22kg for the pasture stage, respectively. In addition, the rate of roughage to concentrate during the entire experimental period was 49.6 to 68.2%(mean 58.5%). 3. Age reached 225 and 250kg of body weight was, on an average, 15.1mo. and 17.6mo., respectively, indicating that increasing the level of concentrates feeding(by 0.5% of body weight) reduced the first pregnancy by 0.9 mo. Ages and body weight for first service were 19.5mo. and 272.2 kg, respectively. Mean pregnant rate of total heads was approximately 52.8%, but appeared to 66.6% for T3 and T4. Therefore, it may be concluded that the optimum level of concentrates for autumn born Hanwoo heifers is 1.8% of body weight for indoor feeding on rice straw-based diet and 1.5% of body weight for a pasture stage, respectively.