• Korean Chemical Engineering Research
• /
• v.59 no.4
• /
• pp.542-547
• /
• 2021

Glass lined impellers are corrosion resistant to most chemicals, including strong acids, and also have a smooth, non-stick surface, easy to clean and free from impurities in the process. Glass lined home base impeller is a multi-purpose impeller designed to stir a wide viscosity range of liquids from low viscosity fluids to high viscosity fluids, among others, cell culture, yeast culture, and beer fermentation pots, especially used for air-water system breathable stirring. The glass lining for HB impellers, which are simple in structure and competitive in performance, is essential to have upper and lower division in order to make the joint area between the impeller and shaft as small as possible. The upper and lower division of the impeller hardly affects the mixing performance, but the aeration performance. In this study, in order to optimize the shape of the Glass Lining HB impeller, a study was conducted on the effect of the angle between the upper and lower impellers, the clearance between the impellers, and the number of baffles on the aeration power. The optimal shape and baffle plate conditions for the Glass lined HB impeller were derived through the study results that the angle and the clearance between the upper and lower impellers decreased the ration of the power consumption with aeration P_g and that without aeration P₀, P_g/P₀.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.4C
• /
• pp.213-220
• /
• 2008

A study on cemented sand reinforced with short fibers was carried out to improve its unconfined compressive strength and brittle behavior. Nak-dong River sand was mixed with Portland cement and polyvinyl alcohol (PVA) fibers. A PVA fiber widely used for concrete reinforcement is randomly distributed into cemented sand. Nak-dong River sand, cement and fibers with optimum water content were compacted in 5 layers and then cured for 7 days. The effect of fiber reinforcement rather than cementation was emphasized by using a small amount of cement. Weakly cemented sand with a cement/sand ratio less than 8% was fiber-reinforced with different fiber ratios and tested for unconfined compression tests. The effect of fiber ratio and cement ratio on unconfined compressive strength was investigated. Fiber-reinforced cemented sand with 2% cement ratio showed up to six times strength to non-reinforced cemented sand. Because of ductile behavior of fiber-reinforced specimens, an axial strain at peak stress of specimens with 2% cement ratio increases up to 7% as a fiber ratio increases. The effect of 1% fiber addition into 2% cemented sand on friction angle and cohesion was analyzed separately. When the fiber reinforcement is related to friction angle increase, the 8% of applied stress transferred to 1% fibers within specimens.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3D
• /
• pp.425-433
• /
• 2006

The presented work provided a predictive equation for dynamic modulus of hot mix asphalt, which showed higher reliability and more simplicity. Lots of test result by UTM at laboratory has been used to develop the precise predictive equation. Evaluation of dynamic modulus for 13mm and 19mm surface course and 25mm of base course of hot mix asphalt with granite aggregate and two asphalt binders (AP-3 and AP-5) were carried out. Superpave Level 1 Mix Design with gyrator compactor was adopted to determine the optimum asphalt binder content (OAC) and the measured ranges of OAC were between 5.1% and 5.4% for surface HMA, and around 4.2% for base HMA. The dynamic modulus and phase angle were determined by testing on UTM, with 5 different testing temperature (-10, 5, 20, 40, & $55^{\circ}C$) and 5 different loading frequencies (0.05, 0.1, 1, 10, 25 Hz). Using the measured dynamic modulus and phase angle, the input parameters of Sigmoidal function equation to represent the master curve were determined and these will be adopted in FEM analysis for asphalt pavements. The effect of each parameter for equation has been compared. Due to the limitation of laboratory tests, the reliability of predictive equation for dynamic modulus is around 80%.

• Korean Journal of Soil Science and Fertilizer
• /
• v.18 no.2
• /
• pp.121-127
• /
• 1985

This study was designed to gain practical data on the use of soil conditioners for more efficient water managements and to establish the optimum levels of structural properties for soil conditioning. A sandy loam and a silt loam soil were each treated with two different soil conditioners, hydrophobic Bitumen or hydrophilic Uresol. The perspex tube 34 cm long were packed homogeneously with air dried soil up to 2 cm below the top, then covered over 2 cm of treated or untreated aggregates. The infiltration rate into the soil columns was measured under simulated rainfall condition. The evaporation study was carried out in the wind tunnel, and the changes of soil moisture distribution of the columns following and during the evaporation were determined by a gamma ray scanner. The infiltration rate of water into the soil column was increased to 18.7-50.8% by the Uresol treatment but it was decreased to less than 25% of control by the Bitumen treatment. Evaporation was decreased to 22.0-68.1% by the Bitumen treatment and to 38.7-68.4% by the Uresol treatment. The water use efficiency of Uresol treated column was increased to more than twice as much as that of untreated soil. Aggregate stability and wetting angle were related to water infiltration and evaporation. A positive and highly significant logarismic relationship was found between the infiltration rate and stability index-wetting angle, evaporation rate and instability index-wetting angle. It was considered that the structural stability is more important than wetting angle. This is true because the structural stability is always positively correlated to water saving, however wettability is positively correlated to the infiltration, and negatively correlated to water saving during the evaporation.

• Tunnel and Underground Space
• /
• v.19 no.1
• /
• pp.31-42
• /
• 2009

One set of hardware system of guide point method (GP method), modified from the multistage convergent photographing technique, was developed to interpret the geometrical characteristics of Joints photogrammetrically on rock slope. Before the field application of the hardware system, the level of errors and constraints that ran be acceptable in the field measurement has been severely investigated in the laboratory and the optimum photographing scheme was analyzed. The range of the most suitable convergence angle between two cameras was $25^{\circ}{\sim}150^{\circ}$ and the photographing distance was about 5.5 m when using a 2 M pixel digital camera. An extended analyzing technique, which was newly developed in this study, was applied to the field measurement to magnify the benefits of GP method. This technique can be applied when survey for the wide range of rock surface is necessary. The global coordinates of ground control points for the neighbor photographing area ran be introduced without any preparation from the previous photographed area using this technique. It could reduce phographing time in the field.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.3
• /
• pp.240-248
• /
• 2016

As a new technical approach, the achievement of an eco-environmental leisure boat with a photovoltaic system is attempted by simultaneously actuating nine photovoltaic solar panels, in association with an applied sail control system by use of wind. In this approach, the photovoltaic system consists of a solar module, an inverter, a battery, and relevant components, while the sail control device is equipped with a sail up/down and mast-turning instrument. Furthermore, this research conducts a performance evaluation of the manufactured prototype and acquires the purposed quantity value and the development purpose items. The significant items-sail up/down speed (seconds) and mast turning angle (degrees)-are evaluated during the performance test. In the process of the performance evaluation, a wind direction sensitivity of 90% and a maximum instant charging power of 900 W were also obtained. In addition, the maximum sail time is evaluated in order to acquire the optimum quantity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.7
• /
• pp.4057-4064
• /
• 2014

In this paper, attempts were made to design a preform for a final punch inexpensively using the proposed approximate optimization method or metamodel-based simulation optimization. The design objective of this work is to achieve a uniform distribution of effective strains, the angle dimension of the preformed punch is chosen as a design variable, and maximum underfill ratio is used as a constraint. For this optimization, a computer simulation of a practical punch forging process is run using DEFORM software, in which a preformed punch(workpiece), a master punch(upper die), and a bottom die are dealt with. A validation method is introduced to determine if the simulation results match the actual forging process. In addition, this work presents the detailed design optimization procedure consisting of (i) generation of an initial metamodel, (ii) metamodel optimization, (iii) validation of metamodel-predicted optimum, and (iv) metamodel improvement.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.9
• /
• pp.5-14
• /
• 2010

This study was aimed to suggest reliable information of shear strength characteristics due to change of saturation in the landfills or slopes during rainfall infiltration. According to the Mohr-Coulomb failure criteria, the characteristics of shear strength due to change of saturation were analyzed for the weathered residual soils which were sampled in the road construction site of Daejeon city. From the direct shear strength tests, the cohesions and the shear resistance angles were showed maximum values in the condition of optimum moisture content, and then decreased in the condition of wet side compaction. In this study, the cohesions were decreased more than 50% according to increasing saturation by infiltration for the compaction soils. But the reductions of the shear resistance angles were about $1{\sim}2^{\circ}$ which was small value, and thus the changes of the saturation were not nearly influenced the shear resistance angle. The influences of the saturation were seemed to very small for the residual strength parameters according to Mohr-Coulomb failure criteria.

• Journal of Computational Design and Engineering
• /
• v.3 no.3
• /
• pp.198-214
• /
• 2016

Oval substrates are widely used in automobiles to reduce the exhaust emissions in Diesel oxidation Catalyst of CI engine. Because of constraints in space and packaging Oval substrate is preferred rather than round substrate. Obtaining the flow uniformity is very challenging in oval substrate comparing with round substrate. In this present work attempts are made to optimize the inlet cone design to achieve the optimal flow uniformity with the help of CATIA V5 which is 3D design tool and CFX which is 3D CFD tool. Initially length of inlet cone and mass flow rate of exhaust stream are analysed to understand the effects of flow uniformity and pressure drop. Then short straight cones and angled cones are designed. Angled cones have been designed by two methodologies. First methodology is rotating flow inlet plane along the substrate in shorter or longer axis. Second method is shifting the flow inlet plane along the longer axis. Large improvement in flow uniformity is observed when the flow inlet plane is shifted along the direction of longer axis by 10, 20 and 30 mm away from geometrical centre. When the inlet plane is rotated again based on 30 mm shifted geometry, significant improvement at rotation angle of $20^{\circ}$ is observed. The flow uniformity is optimum when second shift is performed based on second rotation. This present work shows that for an oval substrate flow, uniformity index can be optimized when inlet cone is angled by rotation of flow inlet plane along axis of substrate.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.3
• /
• pp.483-491
• /
• 2016

Even though the antifogging property of nanosilica coated glass surface is highly increased due to the hydrophilic hydroxyl groups on nanosilica surface, the durability of this property on outdoor glass was diminished rapidly after rain washing. In addition the topology of nanosilica coated glass surface plays very important roles to control an light transmittance or antireflection property. To improve these coating durability and characteristics a hydrophilic nanosilica coating on glass was prepared by coating with 1.5 wt% of nanosilica (Ludox) suspension in the presence of hydrolyzed tetraethylorthosilicate (TEOS). The optimum hydrolysis condition of TEOS in acidic or basic aqueous solution was also examined by contact angle measurement. The final transparent hydrophilic coating layer coated with nanosilica-TEOS in acidic condition (pH=4) showed much improved durability of hydrophilic surface as well as higher visible light transmittance than original uncoated glass by 2 % point.