• Journal of Biosystems Engineering
• /
• 제18권4호
• /
• pp.351-357
• /
• 1993

Recently, a garlic peeler with high performance is being demanded due to increase of consumption of peeled garlic. Although the air type out of various types of garlic peelers is recommended to remove effectively skin of garlic, it has an important problem of large energy consumption. This study was performed to analyze performance of an air-type garlic peeler for its optimum design. Performance indices to represent performance of garlic peeler include peeling ratio, energy efficiency and peeling performance. The factors such as aperture of nozzle, angle and position of air injection, charge rate of garlic, peeling time and so on must be considered to design optimally an air-type garlic peeler.

• 한국통신학회논문지
• /
• 제40권12호
• /
• pp.2324-2330
• /
• 2015

충격성 잡음하의 블라인드 신호처리 분야에서 최대 상호 코렌트로피 알고리듬 (MCC)이 MSE 기반의 알고리듬에 비해 우수한 성능을 보인다. 그러나 MCC 알고리듬에 대한 최적 가중치 조건들이나 충격성 잡음에 대한 내성과 관련된 특성들은 아직 충분히 연구되지 못한 상태이다. 이 논문에서는 MSE기반의 LMS 알고리듬과 비교를 통해 MCC의 최적 가중치의 성질을 분석하여 MCC 알고리듬의 최적 가중치가 MSE기반의 LMS 알고리듬과 같다는 보인다. 또한 MCC의 최적 가중치가 충격성 잡음 하에서도 동요 없이 안정을 유지하는 요인이 입력 크기 조정에 있다는 것을 시뮬레이션을 통해 입증하였다.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제6권
• /
• pp.27-35
• /
• 1998

An experimental study was performed to investigate the optimum cycle of an inverter heat pump as a function of frequency. The performance of the inverter heat pump with the rated cooling capacity of 4,141 W(3,550kcal/h) was measured with a variation of frequency, indoor and outdoor temperature, and length of capillary tube in the psychrometric test room. As a base case, the inverter heat pump with the standard capillary length of l,000mm(optimum size for the frequency of 60Hz) and ASHRAE Test condition "A" was tested by varying frequency from 30Hz to 80Hz. Then, the optimum cycles were investigated by varying the length of capillary tube at each frequency level of 30, 60 and 80Hz. Based on the experimental data, the change of system characteristics between the optimum and the base case were analyzed for each selected frequency level. Generally, for low frequency level(30Hz), the longer length of the capillary tube compared with the standard size showed the higher energy efficiency ratio(EER), while for high frequency level(80Hz) the shorter length of the capillary tube showed the higher EER.

• 설비공학논문집
• /
• 제9권1호
• /
• pp.64-72
• /
• 1997

An experiment study was performed to investigate the optimum cycle of an inverter heat pump as a function of frequency. The performance of the inverter heat pump with the rated cooling capacity of 4141W(3550kcal/h) was measured with a variation of frequency, indoor and outdoor temperature, and length of capillary tube in the psychrometric test room. As a base case, the inverter heat pump with the standard capillary length of 1000mm which was optimum size for the frequency of 60Hz and ARHRAE Test condition A was tested by varying frequency from 30Hz to 80Hz. Then, the optimum cycle was invesigated by varying the length of capillary tube at each frequency levels of 30, 60 and 80Hz. Based on the experimental data, the change of system characteristics between the optimum and the base case were analyzed for each selected frequency levels. Generally, for low frequency level(30Hz), the longer length of the capillary tube compared with the standard size showed the higher EER, while for high frequency level(80Hz) the shorter length of the capillary tube showed the higher EER.

• 한국전자통신학회논문지
• /
• 제6권5호
• /
• pp.621-627
• /
• 2011

본 논문에서는 로드-풀을 이용하여 X-band에서 on-Wafer 상태의 GaN HEMT 소자에 대한 성능을 분석하고 분석한 결과를 바탕으로 최적의 임피던스 점을 분석하였다. 패키징 하기 전 on-Wafer 상태에 있는 반도체 소자의 최적의 임피던스 분석을 통해 소자 자체에서 최적의 성능을 내는 방안을 제안하였다. Gate length가 0.25um이고 Gate Width가 각각 400um, 800um인 소자에 대한 최적의 임피던스를 선정하여 성능을 분석한 결과, 400um는 $P_{sat}$=33.16dBm(2.06W), PAE=67.36%, Gain=15.16dBm의 성능을 가지며, 800um는 $P_{sat}$=35.9 dBm(3.9W), PAE=69.23%, Gain=14.87dB의 성능을 보였다.

• 대한기계학회논문집A
• /
• 제28권4호
• /
• pp.378-385
• /
• 2004

Viscous-driven pumping is a very promising type in microscale applications. However, there exist a few disadvantages such as low efficiency and small volume flow rate. In the present study, a pump with tandem rotating cylinders and its optimum synthesis are proposed fur enhancing pumping performance. First, using an unstructured grid CFD method, we investigate the effects of geometrical parameters and then the performance of the pump with tandem cylinders is evaluated. Next, an optimum design synthesis tool is constructed by combining the aforementioned CFD analysis model with the mathematical optimization model, namely, Modified Method of Feasible Directions (MMFD). This technique is used to optimize the geometrical parameters of the pump, fur maximizing pumping efficiency. From the optimization results, it is believed that the present optimum synthesis is robust and has a potential fur other microfluidic device design.

• 대한기계학회논문집B
• /
• 제24권1호
• /
• pp.124-131
• /
• 2000

In this study, pool boiling performance of Turbo/B-type metal-formed tubes was investigated. Tubes with three different cavity gap width(0.04 mm, 0.07 mm, 0.1 mm) were manufactured and tested using R-11, R-123 and R-134a. Tests were conducted at two different saturation temperatures $4.4^{\circ}C$ and $26.7^{\circ}C.$ Heat flux was varied from 10 kW/m2 to 50 kW/m2. It was found that optimum gap width varied for different refrigerants. For low-pressure refrigerants such as R-11 or R-123, optimum gap width was 0.07 mm. For high-pressure refrigerant R-134a, however, the optimum value was 0.1 mm. Compared with the heat transfer performance of the smooth tube, the metal-formed tubes enhanced the heat transfer coefficients significantly - 6.5 times for R-11, 6.0 times for R-123 and 5.0 times for R-134a (at $4.4^{\circ}C$ saturation temperature and 40 kW/m2 heat flux), which are comparable with the performance of foreign products. The heat transfer coefficients of R-134a were larger than those of R-11 or R-123, and they increased as the saturation temperature increased.

• Tribology and Lubricants
• /
• 제22권5호
• /
• pp.269-275
• /
• 2006

Rolling bearings are classified one of the most important machine elements. The various function of bearings are greatly influenced by grease, and higher performance of rolling bearing greases is required to improve bearing lubrication. Three urea/ether oil greases with different composition were synthesized to compare the performance of these greases. The typical grease physical properties were investigated, and life test of these greases was conducted by FE-9 grease life tester. The grease with higher content of the thickener showed higher performance. After these preliminary test, twelve greases were synthesized and evaluated the performance of dropping point and OIT value. And optimized conditions for grease synthesis were selected by SSRED (Six Sigma Robust Engineering Design) using dropping point and OIT value respectively. The optimized grease using OIT value showed longer grease life than that using dropping point. Two greases were synthesized following the optimum synthesis conditions by means of OIT value. Then grease life and other properties of these greases were investigated. These two greasaes showed longer grease life than typical urea/ether oil grease.

• Earthquakes and Structures
• /
• 제18권2호
• /
• pp.185-199
• /
• 2020

A computationally-efficient method for multi-criteria optimisation is developed for performance-based seismic design of friction energy dissipation dampers in RC structures. The proposed method is based on the concept of Uniform Distribution of Deformation (UDD), where the slip-load distribution along the height of the structure is gradually modified to satisfy multiple performance targets while minimising the additional loads imposed on existing structural elements and foundation. The efficiency of the method is demonstrated through optimisation of 3, 5, 10, 15 and 20-storey RC frames with friction wall dampers subjected to design representative earthquakes using single and multi-criteria optimisation scenarios. The optimum design solutions are obtained in only a few steps, while they are shown to be independent of the selected initial slip loads and convergence factor. Optimum frames satisfy all predefined design targets and exhibit up to 48% lower imposed loads compared to designs using a previously proposed slip-load distribution. It is also shown that dampers designed with optimum slip load patterns based on a set of spectrum-compatible synthetic earthquakes, on average, provide acceptable design solutions under multiple natural seismic excitations representing the design spectrum.

• 대한원격탐사학회지
• /
• 제34권1호
• /
• pp.151-166
• /
• 2018

This paper compares the four selections of performance used in the application of genetic algorithms (GAs) to automatically optimize multispectral pixel cluster for unsupervised classification from KOMPSAT-3 data, since the selection among three main types of operators including crossover and mutation is the driving force to determine the overall operations in the clustering GAs. Experimental results demonstrate that the tournament selection obtains a better performance than the other selections, especially for both the number of generation and the convergence rate. However, it is computationally more expensive than the elitism selection with the slowest convergence rate in the comparison, which has less probability of getting optimum cluster centers than the other selections. Both the ranked-based selection and the proportional roulette wheel selection show similar performance in the average Euclidean distance using the pixel clustering, even the ranked-based is computationally much more expensive than the proportional roulette. With respect to finding global optimum, the tournament selection has higher potential to reach the global optimum prior to the ranked-based selection which spends a lot of computational time in fitness smoothing. The tournament selection-based clustering GA is used to successfully classify the KOMPSAT-3 multispectral data achieving the sufficient the matic accuracy assessment (namely, the achieved Kappa coefficient value of 0.923).