• 한국광학회:학술대회논문집
• /
• 한국광학회 1989년도 제4회 파동 및 레이저 학술발표회 4th Conference on Waves and lasers 논문집 - 한국광학회
• /
• pp.13-19
• /
• 1989

Passive mode-locking of a pulsed Nd:YAG laser is achieved with saturable absorbers, BDN dye in iodoethane solvent and Kodak Eastman # 26 dye in 1,2-dichloroethane solvent, and its optimum conditions are investigated. The thickness of saturable absorbers employed in the laser mode-locking is 0.16~0.50mm. The PBR (peak-to-background ratio) measured in the oscilloscope is 79.8% in Kodak Eastman # 26 dye at the neighbourhood of the peak power, whereas the passive mode-locking with BDN dye gives PBR of 67.7%. BDN and Kodak Eastman # 26 dyes are superior in photostability over Kodak eastman # 9860 and # 9740 dyes which were used previously in passive mode-locking. From the PBR curve, we find that Kodak Eastman # 26dye is more effective than BDN dye in passive mode-locking. The spacing between the adjacent pulses of the pulse train, which depends on the laser cavity length, is measured and is found to be 7 nsec for the cavity length of 100cm.

• Bulletin of the Korean Chemical Society
• /
• 제18권2호
• /
• pp.171-174
• /
• 1997

The initial kinetic energy of laser-ablated Zn cation has been investigated via time-of-flight mass spectrometry. The flight times of the ions have been measured with a high voltage pulse on the extract electrode in the mass spectrometer, which has been delayed from the laser pulse. The time-of-flight equation including the initial kinetic energy term of the ion has been derived for the mass spectrometer. The optimum value of the initial kinetic energy has been extracted by fitting the measured flight times into the time-of-flight equation. The initial kinetic energy of the ions generated by Nd:YAG laser (532 nm) at the power density of 5 × 107 W/cm2 has been determined to be 22-44 kJ/mol.

• 한국공작기계학회논문집
• /
• 제16권4호
• /
• pp.101-107
• /
• 2007

The objective of this research work is to investigate into effects of an auto tracking of the focal distance on the quality of the cut part in the cutting of a low carbon sheet using a high-power CW Nd:YAG laser. An auto-tracking system with a capacitance based distance control loop has been employed to perform a real control of the focal distance. In order to examine the influence of the auto-tracking of a focal distance on the optimum focal distance, the kerfwidth, surface roughness and the formation of the cut section, several linear cutting tests have been carried out using the auto-tracking system. The results of experiments have been shown that the optimum focal distance is 0.9mm. In addition, it has been shown that the variation of kerfwidth and the surface roughness of the cut part with control of the focal distance are reduced 40-80% and 30-55% in comparison with those of the cut part without tracking of the focal distance. From the results of the experiments, it has been found that the real time tracking of the focal distance can improve the part quality.

• 한국광학회지
• /
• 제1권1호
• /
• pp.22-27
• /
• 1990

결합형 모드록킹 극초단 색소레이저의 공진기 길이변화에 따른 펄스폭의 변화를 선형 자체상관기를 이용하여 연구하였다. 색소레이저의 공진기 길이가 여기레이저의 공진기 길이와 일치하였을 경우 펄스폭은 0.64ps이며 완벽하게 모드록킹 되었다. 그러나 최적조건보다 색소레이저 공진기 길이가 긴 경우나 짧은 경우에는 펄스폭은 넓어지며 불완전 모드록킹이 되었다. 즉 색소레이저의 공진기 길이가 여기레이저의 공진기 길이보다 길 경우는 자연방출에 의한 noise 때문에 broad base 가 형성되며, 색소 이득이 증가되기 때문에 자체 상관함수의 첨두출력은 최적조건에서의 색소레이저 공진기 길이보다 5 $\mu\textrm{m}$ 긴 조건에서 최대가 되었다. 또 색소레이저의 스펙트럼은 자연방출에 의한 형광 및 색소 이득이 증가되기 때문에 넓게 됨을 관찰할 수 있었다. 그러나 색소레이저의 공진기 길이가 여기 레이저의 공진기 길이보다 짧은 경우에는, 색소 이득이 적게 됨으로 자체 상관함수의 첨두출력도 약하게 되며 스펙트럼의 전반치폭은 좁게 되었다. 한편 최적조건을 벗어나면 스펙트럼의 중심파장이 이동되는 현상을 관찰할 수 있었다.

• 한국광학회지
• /
• 제19권3호
• /
• pp.229-236
• /
• 2008

주기적으로 분극 반전된 비선형 결정 중에 하나인 PPLN(Periodically Poled MgO(5%) doped Lithium Niobate)과 수 W급의 고출력 연속발진형 파장가변 적외선 레이저 시스템인 DOFA(Diode Laser Oscillator & Fiber Amplifier) 시스템을 이용하여, 이 결정에서 펌핑광을 한번 통과시키는 단일통과와 두 번 통과시키는 이중통과에서의 효율적인 제2고조파 발생 조건을 실험적으로 구하였다. 단일통과에서는 최적의 위상정합온도 $108.9^{\circ}C$에서 최대 출력 2.45 W의 적외선(파장 = 1070 nm) 펌핑광을 사용하여 최대 245 mW의 녹색광원(파장 = 535 nm)인 제 2고조파를 만들었고, 이때의 주파수 변환 효율은 10%였다. 또한 제 2고조파 발생의 효율을 증가시키기 위해서 되 반사용 오목거울과 위상보정을 위한 쐐기유리판을 이용하여 이중통과의 제2고조파 발생장치를 구성하였다. 이때 최적의 위상정합온도 $108.5^{\circ}C$에서 최대 출력 2.45 W의 적외선(파장 = 1070 nm) 펌핑광을 사용하여 최대 383 mW의 녹색광원(파장 = 535 nm)인 제 2고조파를 만들었다. 이때의 변환 효율은 15.6%로써 단일통과에서의 제 2고조파 발생 효율보다 크게 증가함을 확인하였다.

• 한국레이저가공학회지
• /
• 제15권2호
• /
• pp.15-20
• /
• 2012

A novel joining technology was developed to compensate the camber in polymers. The preheating laser beam circulates on the joining location and the accumulated heat serves to increase the flexibility of neighboring polymers. The temperature rises up to the glass transient temperature of the polymers and continually loading spring force closes the gap of camber. The irradiated laser was 808nm central wavelength and the power varied between 2Watt and 5Watt. The laps were adjusted between 3 and 10 and the optimum process parameters were 3Watt and 5 laps for the specific application. An FEM analysis was introduced to understand the mechanism of joining by the transient temperature distribution on the polymers. Thermocouples experiments were also tried to correlate the numerical analysis results and it showed the trend of heat accumulation in experiments.

• Journal of Welding and Joining
• /
• 제32권4호
• /
• pp.20-25
• /
• 2014

Laser heat source was applied on 3D poly urethane model built by 3D printer and cellulous acetate for joining. A diode laser with 808nm wavelength was transmitted through the 3D model and applied on the boundary of ABS/Acetate and 3D poly urethane model. Based on the experimental result, the ABS and 3D built poly-urethane polymers was successfully joined, but the mechanical strength was not enough at the joining boundaries in the range of 6watt to 8watt of laser heat source. However, biodegradable acetate was successfully joined without damaging the 3D built model and mechanical strength was properly achieved. The optimum laser power was found between 5watt and 8watt with scanning speed of 500mm/min, 700mm/min and 1,000mm/min. Based on the SEM analysis the filling mechanism was that the applied pressure on 3D built model squeezed the fluidic thermoplastics, ABS and acetate, into the structure of 3D model. Therefore soundness of joining was strongly depending on the viscosity of thermoplastics in polymers. The developed laser process is expected to increase productivity and minimize the cost for the final products.

• 한국공작기계학회논문집
• /
• 제14권2호
• /
• pp.91-95
• /
• 2005

A feasibility study was performed to see the welding possibility of dissimilar thin-plat materials. These materials were welded for finding the optimum welding condition and evaluating the soundness of welding zone. The welding was attempted under the condition of laser power 500~600w, Pulse width 1.0~2.5ms and frequency 11~18Hz. In this study, the highest tensile-shear strength was observed at laser the low frequency. The suitable welding condition can be obtain at the large pulse width and the low frequency.

• 한국정밀공학회지
• /
• 제21권1호
• /
• pp.46-50
• /
• 2004

The curing characteristics of a liquid photopolymer during microstereolithography and the shape accuracy of thereby fabricated microstructures were investigated experimentally. A He-Cd laser with a wavelength of 442nm and a photopolymer consisted of a commercial resin from SK chemical and a photoinitiat or were used for the experiment. By varying the laser beam power and scanning speed of the focused laser beam, minimum curing thickness of 50 ${\mu}ㅡ$ was obtained. The distortion of solidified structure due to adhesion force was measured and the optimum fabrication conditions were determined. Also, the feasibility of direct fabrication of three-dimensional microstructures by Super IH process was examined.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년 추계학술발표대회 개요집
• /
• pp.190-192
• /
• 2006

The 3-dimensional(3D) chip stacking technology is one of the leading technologies to realize a high density and high performance system in package(SIP). It could be found that it is the advanced process of through-hole via formation with the minimum damaged on the Si-wafer. Laser ablation is very effective method to penetrate through hole on the Si-wafer because it has the advantage that formed under $100{\mu}m$ diameter through-hole via without using a mask. In this paper, we studied the optimum method for a formation of through-hole via using femto-second laser heat sources. Furthermore, the processing parameters of the specimens were several conditions such as power of output, pulse repetition rate as well as irradiation method and time. And also the through-hole via form could be investigated and analyzed by microscope and analyzer.