• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.667-678
• /
• 2002

In this paper, a new radiating structure with a multi-layered two-dimensional metallic disk array was proposed for shaping the flat-topped element pattern. It is an infinite periodic planar array structure with metallic disks finitely stacked above the radiating circular waveguide apertures. The theoretical analysis was in detail performed using rigid full-wave analysis, and was based on modal representations for the fields in the partial regions of the array structure and for the currents on the metallic disks. The final system of linear algebraic equations was derived using the orthogonal property of vector wave functions, mode-matching method, boundary conditions and Galerkin's method, and also their unknown modal coefficients needed for calculation of the array characteristics were determined by Gauss elimination method. The application of the algorithm was demonstrated in an array design for shaping the flat-topped element patterns of $\pm$20$^{\circ}$ beam width in Ka-band. The optimal design parameters normalized by a wavelength for general applications are presented, which are obtained through optimization process on the basis of simulation and design experience. A Ka-band experimental breadboard with symmetric nineteen elements was fabricated to compare simulation results with experimental results. The metallic disks array structure stacked above the radiating circular waveguide apertures was realized using ion-beam deposition method on thin polymer films. It was shown that the calculated and measured element patterns of the breadboard were in very close agreement within the beam scanning range. The result analysis for side lobe and grating lobe was done, and also a blindness phenomenon was discussed, which may cause by multi-layered metallic disk structure at the broadside. Input VSWR of the breadboard was less than 1.14, and its gains measured at 29.0 GHz. 29.5 GHz and 30 GHz were 10.2 dB, 10.0 dB and 10.7 dB, respectively. The experimental and simulation results showed that the proposed multi-layered metallic disk array structure could shape the efficient flat-topped element pattern.

• Culinary science and hospitality research
• /
• v.21 no.1
• /
• pp.77-89
• /
• 2015

The objective of this study was to optimize processing conditions for the production of an instant puffed rice product using response surface methodology (RSM) and contour analysis. Sensory and texture qualities, and physical properties of the puffed rice were analyzed with various processing conditions related to drying and puffing temperature, and moisture content. Preference, color intensity, cohesiveness, rehydration ratio, density and lightness of the puffed rice product significantly varied depending on the processing conditions. The responses showed high $R^2$ values (0.623, 0.852, 0.735, 0.688, and 0.790) and lack-of-fit. Rehydration ratio was found to have a negative correlation with density in the condition of drying and puffing temperature. Lightness and preference scores of the puffed rice increased as the moisture content increased. According to RSM, the preference scores were very highly related to the moisture content, and the optimum processing conditions of the puffed rice product were at $40^{\circ}C$ of drying temperature, with 11.0% of moisture content, and at $232.7^{\circ}C$ of puffing temperature.

• Food Science and Preservation
• /
• v.15 no.1
• /
• pp.58-65
• /
• 2008

The Acorn (Quercus acutissima CARRUTHERS), which contains a large quantity of tannin, should be developed as a processed food as the acorn is rich in natural antioxidants and other valuable components. Accordingly, acorn extraction conditions for polyphenol and gallic acid (both antioxidants) were investigated by response surface methodology. The content of polyphenols were determined under 16 different extraction conditions based upon a central composite design. The parameters varied over $30-70^{\circ}C$ of extraction temperature, 1-5 h of extraction time, and 5-25 mL/g of solvent ratio, Gallic acid extraction was optimal at $60-100^{\circ}C$ extraction temperature, 1-5 h of extraction time, and 5-25 mL/g of solvent ratio, Epicatechin content was highest at $56.77^{\circ}C$, 4.16 hand 22.38 mL/g. Catechin content was highest at $52.37^{\circ}C$, 2h and 23.59 mL/g. The maximum catechin content was $91.30{\mu}g/mL$. Epigallocatechin content was influenced by extraction temperature and time. The maximum epigallocatechin content was $1,066.56{\mu}g/mL$ at $61.42^{\circ}C$, 4.17h, and 9.25 mL/g. The maximum value of epicatechingallate content was $125.39{\mu}g/mL$ at $47.72^{\circ}C$, 3.04h, and 24.93mL/g. Epigallocatechingallate content was influenced principally by solvent ratio and the maximum content was $61.38{\mu}g/mL$ at $48.11^{\circ}C$, 2.96h, and 24.95mL/g. The total polyphenol content was maximal at $1,332.75{\mu}g/mL$, after extraction at $61.50^{\circ}C$, 4.24h, at 9.71mL/g. The higher the extraction temperature and the longer the extraction time, the greater the polyphenol content. Gallic acid content was highest, the maximal level was $30.51{\mu}g/mL$ after $65.84^{\circ}C$, 1.65h at 17.17 mL/g, and this was influenced principally by extraction time and solvent ratio.

• Food Science and Preservation
• /
• v.18 no.6
• /
• pp.980-985
• /
• 2011

This study was conducted to determine the acetic-acid fermentation properties of apple juice (initial alcohol content, apple juice concentration, acetic-acid content, and inoculum size) in flask scale. At the acetic-acid fermentation of apple juice with 3, 5, 7, and 9% initial alcohol content, the maximum acidity after 10-day fermentation was 5.88% when the initial alcohol content was 5%. The acetic-acid fermentation did not proceed normally when the initial alcohol content was 9%. When the initial Brix was $1^{\circ}$, the acidity gradually increased, and the acidity after 12-day acetic-acid fermentation was 4.48%. Above 4% acidity was attained faster when the apple juice concentration was 5 and 10 $^{\circ}Brix$ than when it was 1 and 14 $^{\circ}Brix$. When the initial acidity was 1% or above (0.3, 0.5, 1.0, and 2.0%), the acetic-acid fermentation proceeded normally. The acetic-acid fermentation also proceeded normally when the inoculum sizes were 10 and 15%, and the acidity after eight-day acetic-acid fermentation was 5.60 and 6.05%, respectively. Therefore, the following were considered the optimal acetic-acid fermentation conditions for apple cider vinegar: 5% initial alcohol content, 5 $^{\circ}Brix$ or above apple juice concentration, 1.0% or above initial acidity, and 10% or above inoculum size. Apple cider vinegar with above 5% acidity can be produced within 48 h under the following acetic-acid fermentation conditions: 7% initial alcohol content, about 1% initial acidity, and 10% inoculum volume at $30^{\circ}C$, 30 rpm, and 1.0 vvm, using 14 $^{\circ}Brix$ apple juice in a mini-jar fermentor as a pre-step for industrial-scale adaptation.

• Journal of the Korean Society of Radiology
• /
• v.12 no.7
• /
• pp.895-908
• /
• 2018

As modern science is developed and advanced, examination and number of times using radiation are increasing daily. General diagnostic X-ray generator is installed on stationary form, But X-ray generator was developed because patient who is in the intensive care unit, operation room, emergency room can not move to general x-ray room. What we examine patient by x-ray generator is certainly necessary, So patient exposure is inevitable. but reducing radiation exposure is highly important matter about radiation technology, guardian, patient in the same hospital room, nurse etc. For this reason, rule regarding safety control of diagnostic x-ray generator revised for radiation worker, patient and protector proclaim that mobile diagnostic x-ray shield must placed in case of examine different location excluding operation room, emergency room, intensive care unit. But, radiogical technologist is having a lot of difficulties to examine with mobile x-ray generator, diagnostic x-ray shield partition, image plate and lead apron. So, when we use x-ray generator, we manufacture shield tools can be attached to the mobile x-ray generator On behalf of x-ray shield partition and conduct analysis and in comparison to part of body and distribution of dose rate and find way to reduce radiation exposure through distribution of dose rate of patient within the radiogical technologist, medical team. Mobile x-ray generator aimed at SHIMADZU inc. R-20, We manufactured equipment for shielding x-ray scattered x-ray by installing shielding wall from side to side based on support beam on the mobile x-ray generator. Shielding wall when moving can be folded and designed to expand when examine. Experiment measured five times in each by an angle for dose rate of eyes, thyroid, breast, abdomen and gonad on exposure condition of upper and lower extremity, chest, abdomen which is examined many times by mobile x-ray generator. We used dosimeter RSM-100 made by IJRAD and measured a horizontal dose rate by body part. The result of an experiment, shielding decreasing rate of the front and the rear showed 77 ~ 98.7%. Therefore using self-production shielding wall reduce scattered x-ray occurrence rate and confirm can decrease exposure dose consequently. Therefore, through this study, reduction result which is used shielding wall of self-production will be a role of shielding optimization and it could be answer about reduction of medical exposure recommended by ICRP 103.

• Journal of Plant Biotechnology
• /
• v.46 no.2
• /
• pp.127-135
• /
• 2019

The purpose of this study was to investigate suitable parts for callus induction and optimal concentrations of growth regulators, contained in the medium affecting shoot and rooting for in vitro mass production of Haworthia truncata. Leaves and flower bud showed 100% callus formation rate at NAA $1{\sim}2mgL^{-1}$ treatment, and NAA $1mgL^{-1}$ + TDZ $2mgL^{-1}$ treatment. The flower stalk showed 75% callus formation rate, at NAA $2mgL^{-1}$ + TDZ $2mgL^{-1}$ treatment in H. truncata. While the rate of callus formation was high in leaves and flower bud, leaves were the most efficient in obtaining most culture parts. Shoot induction rate from callus was highest, at NAA $0.1mgL^{-1}$ treatment in H. truncata. Additionally, the number of shoots formation was 66.3 shoots high, in NAA $1mgL^{-1}$ + BA $0.1mgL^{-1}$ treatment in H. truncata. In the case of acclimatization of regenerated plant, growth characteristics did not show significant difference (95%) shading with respect to the different ratio of substrate mixture, and it was determined that would be appropriate, considering plant height and appearance preference of H. truncata. It was established that optimization of culture condition, was responsible for mass propagation in vitro cultures of H. truncata.

• Journal of Plant Biotechnology
• /
• v.46 no.1
• /
• pp.22-31
• /
• 2019

The objective of this study was to investigate the suitable parts for callus induction and optimal concentrations of growth regulators contained in the medium affecting shooting and rooting Echeveria laui and Echeveria elegans for in vitro mass production. To determine the suitable plant parts for callus induction, the leaves were divided into upper, medium and bottom parts and cultured on MS medium at different concentrations with $0{\sim}2mgL^{-1}\;NAA$ and $0{\sim}4 mgL^{-1}BA$. The upper and middle parts of leaves both showed 100% callus formation rate with $NAA\;1\;mgL^{-1}$ and $BA\;1\;mgL^{-1}$ treatment in E. laui. The middle parts of leaves showed 83.3% callus formation rate at $NAA\;2\;mgL^{-1}$ and BA 4 mgL-1 treatment in E. elegans. The shoot induction rate from callus was highest at $NAA\;0.1\;mgL^{-1}$ and $BA\;3\;mgL^{-1}$ treatment in E. laui and $NAA\;0.3\;mgL^{-1}$ in E. elegans. In addition, the number of shoots formation was 10.4 shoots high in $NAA\;1\;mgL^{-1}$ and $BA\;1\;mgL^{-1}$ treatment in E. laui and 12.0 shoots in most effective $NAA\;1\;mgL^{-1}$ and $BA\;0.1\;mgL^{-1}$ treatment in E. elegans. In the case of acclimatization of regenerated plant, growth characteristics did not show any significant difference (35 ~ 55%) shading with respect to the different ratio of substrate mixture, and it was determined that would be appropriate considered plant height and appearance preference of E. laui and E. elegans. It was established that the optimization of culture condition was responsible for the mass propagation in vitro cultures of E. laui and E. elegans.

• Journal of the Korean Electrochemical Society
• /
• v.26 no.1
• /
• pp.1-10
• /
• 2023

The cathode, which is one of the four major components of a lithium secondary battery, is an important component responsible for the energy density of the battery. The mixing process of active material, conductive material, and polymer binder is very essential in the commonly used wet manufacturing process of the cathode. However, in the case of mixing conditions of the cathode, since there is no systematic method, in most cases, differences in performance occur depending on the manufacturer. Therefore, LiMn₂O₄ (LMO) cathodes were prepared using a commonly used THINKY mixer and homogenizer to optimize the mixing method in the cathode slurry preparation step, and their characteristics were compared. Each mixing condition was performed at 2000 RPM and 7 min, and to determine only the difference in the mixing method during the manufacture of the cathode other experiment conditions (mixing time, material input order, etc.) were kept constant. Among the manufactured THINKY mixer LMO (TLMO) and homogenizer LMO (HLMO), HLMO has more uniform particle dispersion than TLMO, and thus shows higher adhesive strength. Also, the result of the electrochemical evaluation reveals that HLMO cathode showed improved performance with a more stable life cycle compared to TLMO. The initial discharge capacity retention rate of HLMO at 69 cycles was 88%, which is about 4.4 times higher than that of TLMO, and in the case of rate capability, HLMO exhibited a better capacity retention even at high C-rates of 10, 15, and 20 C and the capacity recovery at 1 C was higher than that of TLMO. It's postulated that the use of a homogenizer improves the characteristics of the slurry containing the active material, the conductive material, and the polymer binder creating an electrically conductive network formed by uniformly dispersing the conductive material suppressing its strong electrostatic properties thus avoiding aggregation. As a result, surface contact between the active material and the conductive material increases, electrons move more smoothly, changes in lattice volume during charging and discharging are more reversible and contact resistance between the active material and the conductive material is suppressed.

• Radiation Oncology Journal
• /
• v.23 no.4
• /
• pp.223-229
• /
• 2005

Purpose: In this work we designed and made MPBP(Multi Purpose Brachytherapy Phantom). The MPBP enables one to reproduce the same patient set-up in MPBP as the treatment of the patient and we tried to get an exact analysis of rectal doses in the phantom without need of in-vivo dosimetry. Materials and Methods: Dose measurements were tried at a point of rectum 1, the reference point of rectum, with a diode detector for 4 patients treated with tandem and ovoid for a brachytherapy of a cervix cancer. Total 20 times of rectal dose measurements were made with 5 times a patient. The set-up variation of the diode detector was analyzed. The same patient set-ups were reproduced in self-made MPBP and then rectal doses were measured with TLD. Results: The measurement results of the diode detector showed that the set-up variation of the diode detector was the maximum $11.25{\pm}0.95mm$ in the y-direction for Patient 1 and the maximum $9.90{\pm}4.50mm,\;20.85{\pm}4.50mm,\;and\;19.15{\pm}3.33mm$ in the z-direction for Patient 2, 3, and 4, respectively. Un analyzing the degree of variation in 3 directions the more variation was showed in the z-direction than x- and y-direction except Patient 1. The results of TLD measurements in MPBP showed the relative maximum error of 8.6% and 7.7% at a point of rectum 1 for Patient 1 and 4, respectively and 1.7% and 1.2% for Patient 2 and 3, respectively. The doses measured at R1 and R2 were higher than those calculated except R point of Patient 2. this can be thought to related to the algorithm of dose calculation, whcih corrects for air and water but is guessed not to consider the correction for the scattered rays, but by considering the self-error (${\pm}5%$) TLD has the relative error of values measured and calculated was analyzed to be in a good agreement within 15%. Conclusion: The reproducibility of dose measurements under the same condition as the treatment could be achieved owing to the self-made MPMP and the dose at the point of interest could be analyzed accurately. If a treatment is peformed after achieving dose optimization using the data obtained in the phantom, dose will be able to be minimized to important organs.

• Asia pacific journal of information systems
• /
• v.24 no.4
• /
• pp.443-472
• /
• 2014

To survive in the global competitive environment, enterprise should be able to solve various problems and find the optimal solution effectively. The big-data is being perceived as a tool for solving enterprise problems effectively and improve competitiveness with its' various problem solving and advanced predictive capabilities. Due to its remarkable performance, the implementation of big data systems has been increased through many enterprises around the world. Currently the big-data is called the 'crude oil' of the 21st century and is expected to provide competitive superiority. The reason why the big data is in the limelight is because while the conventional IT technology has been falling behind much in its possibility level, the big data has gone beyond the technological possibility and has the advantage of being utilized to create new values such as business optimization and new business creation through analysis of big data. Since the big data has been introduced too hastily without considering the strategic value deduction and achievement obtained through the big data, however, there are difficulties in the strategic value deduction and data utilization that can be gained through big data. According to the survey result of 1,800 IT professionals from 18 countries world wide, the percentage of the corporation where the big data is being utilized well was only 28%, and many of them responded that they are having difficulties in strategic value deduction and operation through big data. The strategic value should be deducted and environment phases like corporate internal and external related regulations and systems should be considered in order to introduce big data, but these factors were not well being reflected. The cause of the failure turned out to be that the big data was introduced by way of the IT trend and surrounding environment, but it was introduced hastily in the situation where the introduction condition was not well arranged. The strategic value which can be obtained through big data should be clearly comprehended and systematic environment analysis is very important about applicability in order to introduce successful big data, but since the corporations are considering only partial achievements and technological phases that can be obtained through big data, the successful introduction is not being made. Previous study shows that most of big data researches are focused on big data concept, cases, and practical suggestions without empirical study. The purpose of this study is provide the theoretically and practically useful implementation framework and strategies of big data systems with conducting comprehensive literature review, finding influencing factors for successful big data systems implementation, and analysing empirical models. To do this, the elements which can affect the introduction intention of big data were deducted by reviewing the information system's successful factors, strategic value perception factors, considering factors for the information system introduction environment and big data related literature in order to comprehend the effect factors when the corporations introduce big data and structured questionnaire was developed. After that, the questionnaire and the statistical analysis were performed with the people in charge of the big data inside the corporations as objects. According to the statistical analysis, it was shown that the strategic value perception factor and the inside-industry environmental factors affected positively the introduction intention of big data. The theoretical, practical and political implications deducted from the study result is as follows. The frist theoretical implication is that this study has proposed theoretically effect factors which affect the introduction intention of big data by reviewing the strategic value perception and environmental factors and big data related precedent studies and proposed the variables and measurement items which were analyzed empirically and verified. This study has meaning in that it has measured the influence of each variable on the introduction intention by verifying the relationship between the independent variables and the dependent variables through structural equation model. Second, this study has defined the independent variable(strategic value perception, environment), dependent variable(introduction intention) and regulatory variable(type of business and corporate size) about big data introduction intention and has arranged theoretical base in studying big data related field empirically afterwards by developing measurement items which has obtained credibility and validity. Third, by verifying the strategic value perception factors and the significance about environmental factors proposed in the conventional precedent studies, this study will be able to give aid to the afterwards empirical study about effect factors on big data introduction. The operational implications are as follows. First, this study has arranged the empirical study base about big data field by investigating the cause and effect relationship about the influence of the strategic value perception factor and environmental factor on the introduction intention and proposing the measurement items which has obtained the justice, credibility and validity etc. Second, this study has proposed the study result that the strategic value perception factor affects positively the big data introduction intention and it has meaning in that the importance of the strategic value perception has been presented. Third, the study has proposed that the corporation which introduces big data should consider the big data introduction through precise analysis about industry's internal environment. Fourth, this study has proposed the point that the size and type of business of the corresponding corporation should be considered in introducing the big data by presenting the difference of the effect factors of big data introduction depending on the size and type of business of the corporation. The political implications are as follows. First, variety of utilization of big data is needed. The strategic value that big data has can be accessed in various ways in the product, service field, productivity field, decision making field etc and can be utilized in all the business fields based on that, but the parts that main domestic corporations are considering are limited to some parts of the products and service fields. Accordingly, in introducing big data, reviewing the phase about utilization in detail and design the big data system in a form which can maximize the utilization rate will be necessary. Second, the study is proposing the burden of the cost of the system introduction, difficulty in utilization in the system and lack of credibility in the supply corporations etc in the big data introduction phase by corporations. Since the world IT corporations are predominating the big data market, the big data introduction of domestic corporations can not but to be dependent on the foreign corporations. When considering that fact, that our country does not have global IT corporations even though it is world powerful IT country, the big data can be thought to be the chance to rear world level corporations. Accordingly, the government shall need to rear star corporations through active political support. Third, the corporations' internal and external professional manpower for the big data introduction and operation lacks. Big data is a system where how valuable data can be deducted utilizing data is more important than the system construction itself. For this, talent who are equipped with academic knowledge and experience in various fields like IT, statistics, strategy and management etc and manpower training should be implemented through systematic education for these talents. This study has arranged theoretical base for empirical studies about big data related fields by comprehending the main variables which affect the big data introduction intention and verifying them and is expected to be able to propose useful guidelines for the corporations and policy developers who are considering big data implementationby analyzing empirically that theoretical base.