• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.304-308
• /
• 2008

The optimal design of two stage evaporation & absorption system which is related to the large temperature difference system was investigated numerically in the absorption refrigeration system. The concentrations at inlet & oulet of absorber are 62.9% and 56.9%, but in two stage absorption system the values are 62.2% and 56.2%. Therefore strong solution & weak solution became diluted than the standard value. The amount of weak solution circulation can be reduced in absorption refrigeration system, and the sensible heat load is more reduced to enhance the COP of system. As UAR is increased, COP becomes larger, and this means the role of top section is more important than bottom section in two stage evaporation & absorption system. But the increase of COP becomes slower at 0.7 of UAR ratio. The performance of Type2 is higher than Type1 in COP with the flow direction of cooling waters. This phenomena is due to the active absorption of vapor -absorption & lower temp. cooling water is more effective. The pressure at bottom section becomes higher & that at top section becomes lower and therefore the circulation rate can be diminished more.

• The Korean Journal of Food And Nutrition
• /
• v.20 no.1
• /
• pp.20-26
• /
• 2007

The characteristics of sponge cake were investigated with various flour types and amounts of ginseng powder. Sponge cake made with medium flour in combination with 2 and 4% mixtures of ginseng powder was found to be optimal as a cake flour control, being unaffected by the addition of ginseng powder. The results of alveogram showed that increment of ginseng powder decreased over pressure(P), extensibility(L) and swelling index(G) value. Farinogram, consistency, water absorption, stability, time to breakdown and the farinograph quality number all decreased with increasing ginseng powder however, the longest development time was the medium flour with a 2% ginseng powder mixture. Water activities were not significantly affected by addition of ginseng powder, however the 2% ginseng powder mixture showed a slight decrease in water activity. Addition of ginseng powder caused an increase in darkness, as well as redness and yellowness. The results of the sensory test suggest that the 2% ginseng powder mixture was preferable for the cake flour control.

• Fire Science and Engineering
• /
• v.24 no.4
• /
• pp.41-46
• /
• 2010

High strength concrete (HSC) has been mainly used in large SOC structures. HSC have superior property as well as improvement in durability compared with normal strength concrete. In spite of durability of HSC, explosive spalling in concrete front surface near the source of fire occurs serious problem in structural safety. Therefore, this study is concerned with experimentally investigation of fire resistance at high temperature due to fireproof material covering thickness in addition to concrete cover. From the test result, it was appeared that the use of fireproof material results in good performance for fire resistance and spalling prevention, and the optimal fireproof covering thickness is 1~3mm. On the other hand, the temperature was rapidly increased by explosive spalling within 30 minutes and showed very little rise caused by evaporation heat after then. It was also found that the void channel was remained at high temperature as PP fiber melts at about $200^{\circ}C$, and the pore pressure in concrete was decreased.

• Journal of Korea Water Resources Association
• /
• v.48 no.10
• /
• pp.845-855
• /
• 2015

Studies of optimizing pump operation in water distribution networks (WDN) are receiving spotlight in recent days. However, the water networks are quite complex including thousands of or even tens of thousands of nodes and pipes, thus simulation time is an issue. In some cases, implementing a computer model for pump operation decisions is restrictive due to intensive computation time. To that end, it is necessary to reduce the simulation time of water networks by simplifying the network layout. In this study, WDN skeletonization approaches were suggested and applied to a real water transmission network in South Korea. In skeletonizing the original network, it was constrained to match the water pressure and water age in the same junction locations to maintain the hydraulic and water quality characteristics in the skeletonized network. Using the skeletonization approaches suggested in this study, it is expected to reduce the simulation time of WDN and apply for developing a computer module of WDN real-time optimal operation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.3
• /
• pp.103-111
• /
• 2006

The spray behavior of direct-injection spark-ignition(DISI) engines is crucial for obtaining the required mixture distribution for optimal engine combustion. The spray characteristics of DISI engines are affected by many factors such as piston bowl shape, air flow, ambient temperature, injection pressure and fuel temperature. In this study, the effect of fuel temperature on the spray and combustion characteristics was partially investigated for the wall-guided system. The effect of fuel temperature on the fan spray characteristics was investigated in a steady flow rig embodied in a wind tunnel. The shadowgraphy and direct imaging methods were employed to visualize the spray development at different fuel temperatures. The microscopic characteristics of spray were investigated by the particle size measurements using a phase Doppler anemometry(PDA). The effect of injector temperature on the engine combustion characteristics during cold start and warming-up operating conditions was also investigated. Optical single cylinder DISI engine was used for the test, and the successive flame images captured by high speed camera, engine-out emissions and performance data have been analyzed. This could give the way of forming the stable mixture near the spark plug to achieve the stable combustion of DISI engine.

• Journal of Korea Foundry Society
• /
• v.33 no.4
• /
• pp.157-161
• /
• 2013

A ribbon-type polycrystalline silicon wafer was directly fabricated from liquid silicon via a novel technique for both a fast growth rate and large grain size by exploiting gas pressure. Effects of processing parameters such as moving speed of a dummy bar and the length of the solidification zone on continuous casting of the silicon wafer were investigated. Silicon melt extruded from the growth region in the case of a solidification zone with a length of 1cm due to incomplete solidification. In case of a solidification zone wieh a length of 2 cm, on the other hand, continuous casting of the wafer was impossible due to the volume expansion of silicon derived from the liquid-solid transformation in solidification zone. Consequently, the optimal length of the solidification zone was 1.5 cm for maintaining the position of the solid-liquid interface in the solidification zone. The silicon wafer could be continuously casted when the moving speed of the dummy bar was 6 cm/min, but liquid silicon extruded from the growth region without solidification when the moving speed of the dummy bar was ${\geq}$ 9 cm/min. This was due to a shift of the position of the solid-liquid interface from the solidification zone to the moving area. The present study reports experimental findings on a new direct growth system for obtaining silicon wafers with both high quality and productivity, as a candidate for an alternate route for the fabrication of ribbon-type silicon wafers.

• Polymer(Korea)
• /
• v.37 no.5
• /
• pp.642-648
• /
• 2013

There is a kind of abnormal noise known to come from the stick-slip mechanism induced by frictional impulses during the sliding of two polymeric plates. In this work, quantitative analysis of abnormal noise is carried out based on experimental results. Some combinations of polymer plates, such as an ABS base-plate contacted to ABS, PP, MIPS, and POM plates, which are well-known materials used in home-appliances, are studied to obtain the best combination of polymer plates in order to reduce the abnormal noise. For the experiments, a rig for the test was set up and a methodology was proposed. In addition, the effects of the surface roughness of the plate, the normal loading force, and the relative sliding speed between the two contact plates were evaluated in order to understand the reason for the abnormal noise. Through this experimental work, the optimal combination of materials was ABS/POM system to reduce the noise in real industrial applications.

• Journal of Environmental Science International
• /
• v.13 no.10
• /
• pp.883-890
• /
• 2004

The purpose of this study is to survey and analyze the growth, management and surrounding environment of the big and old trees in Kyoungju-si or the cultural assets alive in our history, and thereby, provide for some data useful to their reasonable protection and use of their surrounding areas. As a result of surveying the growth conditions of the big and old trees, it was found that the height of new grass was 10.5cm on average, the activity scale of the wood was 7.2k$\Omega$, the soil hardness was $16.7kg/cm^2$, the soil acidity was pH 4.8, and the soil moisture was $13.3\%$. Such findings suggest that the soil has been acidified by people's frequent passages, but that the other growth conditions are more or less normal. Hence, it is desirable to secure a sufficient space around the trees or reduce people's stamping pressure with some mechanisms. On the other hand, the visible conditions of the trees were found more or less normal, but many trees remained cut or barked (with some cavities), requiring an optimal treatment or measure. Lastly, as the population has decreased in the suburban traditional villages, the surrounding environment seems to be less vulnerable to people's frequent visits. Nevertheless, in consideration of the fact that there are only a few public space for the villagers, it is deemed necessary to rearrange or maintain some parts of the surrounding environment as public space for villagers or hikers.

• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.551-556
• /
• 2013

AlN films with c-axis orientation and thermal conductivity characteristics were deposited by using Pulsed Laser Deposition and the films were characterized by changing the deposition conditions. In particular, we investigated the optimal conditions for the application of a heat sinking plane AlN thin film. Epitaxial AlN films were deposited on sapphire ($c-Al_2O_3$) single crystals by pulsed laser deposition (PLD) with an AlN target. AlN films were deposited at a fixed pressure of $2{\times}10^{-5}$ Torr, while the substrate temperature was varied from 500 to $700^{\circ}C$. According to the experimental results of the growth temperature of the thin film, AlN thin films were confirmed with a highly c-axis orientation, maximum grain size, and high thermal conductivity at $650^{\circ}C$. The thermal conductivity of the AlN thin film was found to increase compared to bulk AlN near the band gap value of 6.2 eV.

• Journal of Drive and Control
• /
• v.12 no.1
• /
• pp.1-8
• /
• 2015

The stability of friction characteristics and thermal management for a dry type dual clutch transmission (DCT) are inferior to those of a wet clutch. Too high temperature resulting from frequent engagement of DCT speeds up degradation or serious wear of the pressure plate or burning of the clutch disk lining. Even though it is significantly important to estimate the temperature of a dry double clutch (DDC) in real-time, few meaningful study of the thermal model of DDC has been known yet. This study presented a thermal analytical model of lumped parameters for a DDC by analyzing its each component firstly. Then a series of experimental test was carried out on the test bench with a patented temperature telemetry system to validate the proposed thermal model. The thermal model, whose optimal parameter values were found by optimization algorithm, was also simulated on the experimental test conditions. The simulation results of DDC temperature show consistency with the experiment, which validates the proposed thermal model of DDC.