• Tunnel and Underground Space
• /
• v.22 no.3
• /
• pp.163-172
• /
• 2012

As more diesel engines have been employed in underground limestone mines with large cross section, underground space environment is worsened by diesel exhausts and heat flow. This paper aims for the ultimate goal to optimize the work place environment through assuring the optimal required ventilation rate based on the analysis of the airflow, diesel exhaust gas concentrations and the effects of mechanization and deepening working face on temperature and humidity. Due to the insufficient capacity of the main exhaust fan and poor airway management, stagnant airflows were observed at various locations, while the flow direction was reversed instantly with passing diesel equipment and the flow reversal was also made by the seasonal variation of the outside surface weather. During the loading operation, CO concentration measurements were found to be frequently higher than the threshold limit of 50 ppm, and most of the $NO_2$ measurements during drilling and loading operations shows even more serious levels surpassing the permissible limit of 3 ppm. The actual ventilation quantity was considerably less than the required quantity estimated by the mine health and safety law, and this shortage problem was less serious in colder winter showing more effectiveness of the natural ventilation.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.25 no.4
• /
• pp.301-306
• /
• 1992

In order to determine the optimal conditions for the process of acetic acid fermentation, the kinetics of Acetobacter aceti fermentation in submerged batch cultures were studied at different agitation speeds and air flow rates. The maximum cell concentration was noted after about 48 hr fermentation and the time course of Acetobactey aceti fermentation showed a distinct feature of growth-associated product formation. At agitation speeds 700, 500, and 300 rpm fixed on air flow rate 1 v/v/M, specific grow rates were $3.97\times10^{-2},\;3.82\times10^{-2},\;and\;2.04\times10^{-2\} \;hr^{-1}$, saturation constants were 61.4, 64.6, and 69.4mg/ml. and volumetric oxygen transfer coefficients were 0.9337, 0.4468, and 0.1701 $min^{-1},$ respectively. At air flow rates 1.25, 1.00, and 0.75 v/v/M fixed on agitation speed 500 rpm, specific growth rates were $3.90\times10^{-2},\;3.82\times10^{-2},\;and\;2.37\times10^{-2}\;hr^{-1}$, saturation constants were 63.4, 64.6, and 64.9 mg/ml, and volumetric oxygen transfer coefficient were 0.4923, 0.4468, and 0.3509 $min^{-1},$ respectively.

• Journal of Wetlands Research
• /
• v.18 no.3
• /
• pp.324-329
• /
• 2016

Constructed wetlands are widely applied in urban and rural areas for various purposes such as pollutants reduction, acquisition of eco-spaces and habitats, flooding reduction, acquisition of water resources and environmental education. Since the design of constructed wetlands utilizes ecosystems, special consideration must be given to ecological mechanisms, environmental mechanisms and hydrological mechanisms. To ensure the sustainable functionality of constructed wetlands, it is necessary to achieve stable flow rate and velocity, and remove sediments to ensure sufficient space for detention. To enhance the efficiency of constructed wetland sedimentation basins, this study determined the optimal position for baffle installation, and applied Computational Fluid Dynamics (CFD) to the cross-sectional design of wetlands. CFD analysis revealed that the decrease in flow velocity with baffle installation enhanced the efficiency of sedimentation of particulate matters. Vertical baffles had higher sedimentation efficiency than those with an inclined angle. When vertical baffles were installed in the sedimentation basin of a hybrid constructed wetland to reduce non-point source pollutants in urban areas, the average flow velocity within the basin decreased by 10~30%, while the sedimentation efficiency improved by 1.3~1.5 times. The application of CFD to constructed wetlands is expected to improve the cost efficiency of designing hybrid constructed wetlands with high removal efficiency.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.7
• /
• pp.939-944
• /
• 2018

Clean fire extinguishing agents refer to chemical that can replace Halon 1211 and Halon 1310 according to the Montreal Protocol fermented to protect the Earth's ozone layer. In Korea and abroad, system standardization and performance evaluation of clean fire extinguishing agents are being carried out. This paper proposes an optimal nozzle shape by modeling and numerical analysis of various nozzle shapes based on general clean fire extinguishing system. The ejection speed of the nozzle can be improved by studying three - dimensional modeling of the nozzle for two shapes, Type A and B. Flow analysis was performed on the two types of nozzles and the gas velocity and pressure distribution were measured with different nozzle diameters. It was confirmed that the jetting speed was changed at the nozzle outlet according to the number and diameter of the nozzle holes. The flow rate increased with increasing the pressure regardless of the nozzle hole diameter. Based on the results obtained from the experiment, the K-factor value was deduced. Finally, a nozzle with a 12-hole structure with a 5-mm nozzle hole was proposed.

• KDI Journal of Economic Policy
• /
• v.46 no.1
• /
• pp.91-129
• /
• 2024

The Bank of Korea, through a legal amendment in 2011 following the financial crisis, was entrusted with the additional responsibility of financial stability beyond its existing mandate of price stability. Since then, concerns have been raised about the prolonged increase in household debt compared to income conditions, which could constrain consumption and growth and increase the possibility of a crisis in the event of negative economic shocks. The current accumulation of financial imbalances suggests a critical period for the government and central bank to be more vigilant, ensuring it does not impede the stable flow of our financial and economic systems. This study examines the applicability of the Integrated Inflation Targeting (IIT) framework proposed by the Bank for International Settlements (BIS) for macro-financial stability in promoting long-term economic stability. Using VAR models, the study reveals a clear increase in risk appetite following interest rate cuts after the financial crisis, leading to a rise in household debt. Additionally, analyzing the central bank's conduct of monetary policy from 2000 to 2021 through DSGE models indicates that the Bank of Korea has operated with a form of IIT, considering both inflation and growth in its policy decisions, with some responsiveness to the increase in household debt. However, the estimation of a high interest rate smoothing coefficient suggests a cautious approach to interest rate adjustments. Furthermore, estimating the optimal interest rate rule to minimize the central bank's loss function reveals that a policy considering inflation, growth, and being mindful of household credit conditions is superior. It suggests that the policy of actively adjusting the benchmark interest rate in response to changes in economic conditions and being attentive to household credit situations when household debt is increasing rapidly compared to income conditions has been analyzed as a desirable policy approach. Based on these findings, we conclude that the integrated inflation targeting framework proposed by the BIS could be considered as an alternative policy system that supports the stable growth of the economy in the medium to long term.

• Tuberculosis and Respiratory Diseases
• /
• v.45 no.1
• /
• pp.140-152
• /
• 1998

Background: Prone position improves oxygenation in patients with ARDS probably by reducing shunt Reduction of shunt in prone position is thought to be effected by lowering of the critical opening pressure (COP) of the dorsal lung because the pleural pressure becomes less positive in prone position compared to supine position. It can then be assumed that prone position would bring about greater improvement in oxygenation when PEEP applied in supine position is just beneath COP than when PEEP is above COP. Hemodynamically, prone position is expected to attenuate the lifting of cardiac fossa induced by PEEP. Based on these backgrounds, we investigated whether the effect of prone position on oxygenation differs in magnitude according to the level of PEEP applied in supine position, and whether impaired cardiac output in supine position by PEEP can be restored in prone position. Methods: In seven mongrel dogs, $PaO_2/F_1O_2$(P/F) was measured in supine position and at prone position 30 min. Cardiac output (CO), stroke volume (SV), pulse rate (PR), and pulmonary artery occlusion pressure (PAOP) were measured in supine position, at prone position 5 min, and at prone position 30 min. After ARDS was established with warmed saline lavage(P/F ratio $134{\pm}72$ mm Hg), inflection point was measured by constant flow method($6.6{\pm}1.4cm$ $H_2O$), and the above variables were measured in supine and prone positions under the application of Low PEEP($5.0{\pm}1.2cm$ $H_2O$), and Optimal PEEP($9.0{\pm}1.2cm$ $H_2O$)(2 cm $H_2O$ below and above the inflection point, respectively) consecutively. Results : P/F ratio in supine position was $195{\pm}112$ mm Hg at Low PEEP and $466{\pm}63$ mm Hg at Optimal PEEP(p=0.003). Net increase of P/F ratio at prone position 30 min, however, was far greater at Low PEEP($205{\pm}90$ mm Hg) than at Optimal PEEP($33{\pm}33$ mm Hg)(p=0.009). Compared to CO in supine position at Optimal PEEP($2.4{\pm}0.5$ L/min), CO in prone improved to $3.4{\pm}0.6$ L/min at prone position 5 min (p=0.0180) and $3.6{\pm}0.7$ L/min at prone position 30 min (p=0.0180). Improvement in CO was attributable to the increase in SV: $14{\pm}2$ ml in supine position, $20{\pm}2$ ml at prone position 5 min (p=0.0180), and $21{\pm}2$ ml at prone position 30 min (p=0.0180), but not to change in PR or PAOP. When the dogs were turned to supine position again, MAP ($92{\pm}23$ mm Hg, p=0.009), CO ($2.4{\pm}0.5$ L/min, p=0.0277) and SV ($14{\pm}1$ ml, p=0.0277) were all decreased compared to prone position 30 min. Conclusion: Prone position in a dog with saline-lavaged acute lung injury appeared to augment the effect of relatively low PEEP on oxygenation, and also attenuate the adverse hemodynamic effect of relatively high PEEP. These findings suggest that a PEEP lower than Optimal PEEP can be adopted in prone position to achieve the goal of alveolar recruitment in ARDS avoiding the hemodynamic complications of a higher PEEP at the same time.

• Journal of Energy Engineering
• /
• v.8 no.4
• /
• pp.592-604
• /
• 1999

The steady state and dynamic characteristics of large cell area MCFC stacks were analyzed to solve the problems such as temperature difference generated in stacks and pressure difference between anode and cathode. Manipulated variables (current density, duel utilization rate, oxidant utilization rate) and controlled variables (temperature difference, anode and cathode pressure difference) which had an important effect on the MCFC stack performance were determined using operation results of two types of MCFC stacks (5kW (3,000 $\textrm{cm}^2$, 20 ea). 3kW (6,000 $\textrm{cm}^2$, 5ea)). The stability and transfer function representing system dynamics were obtained by steady state gain rate which showed the relative change between MVs and CVs. The transfer function was a 3$\times$3 matrix and a typical first order system without time delay. The optimal operating condition of large cell area MCFC stacks could be determined by analyzing dynamic characteristics. In case of a 5 kW MCFC stack, pressurized operation with recycle flow should be used to control the outlet temperature less than 68$0^{\circ}C$ and to control the MCFC system effectively. MIMO control or decoupler should be used to remove the interaction between MVs and CVs. This result will be used as important data in determining the control structure design and operation mode of large cell area MCFC systems in the future.

• Journal of Bio-Environment Control
• /
• v.28 no.3
• /
• pp.225-233
• /
• 2019

In the summer season, natural ventilation is commonly used to reduce the inside air temperature of greenhouse when it rises above the optimal level. The greenhouse shape, vent design, and position play a critical role in the effectiveness of natural ventilation. In this study, computational fluid dynamics (CFD) was employed to investigate the effect of different roof vent designs along with side vents on the buoyancy-driven natural ventilation. The boussinesq hypothesis was used to simulate the buoyancy effect to the whole computational domain. RNG K-epsilon turbulence model was utilized, and a discrete originates (DO) radiation model was used with solar ray tracing to simulate the effect of solar radiation. The CFD model was validated using the experimentally obtained greenhouse internal temperature, and the experimental and computed results agreed well. Furthermore, this model was adopted to compare the internal greenhouse air temperature and ventilation rate for seven different roof vent designs. The results revealed that the inside-to-outside air temperature differences of the greenhouse varied from 3.2 to $9.6^{\circ}C$ depending on the different studied roof vent types. Moreover, the ventilation rate was within the range from 0.33 to $0.49min^{-1}$. Our findings show that the conical type roof ventilation has minimum inside-to-outside air temperature difference of $3.2^{\circ}C$ and a maximum ventilation rate of $0.49min^{-1}$.

• Journal of Mushroom
• /
• v.6 no.1
• /
• pp.27-31
• /
• 2008

The optimization of submerged culture conditions for mycelial growth and exopolysaccharide (EPS) production in an edible mushroom Tremella fuciformis were studied in shake flasks and bioreactors. The temperature of $28^{\circ}C$ and pH 8 in the beginning of fermentation in agitated flasks was the most efficient condition to obtain maximum mycelial biomass and EPS. The optimal medium constituents were as follows (g l-1): glucose 20, tryptone 2, $KH_2PO_4$ 0.46, $K_2HPO_4$ 1 and $MgSO_4H_2O$ 0.5. The fungus was cultivated under various agitation and aeration conditions in a 5L stirred-tank bioreactor. The maximum cell mass and EPS production were obtained at a relatively high agitation speed of 200 rpm and at an aeration rate of 2 vvm. The flow behavior of the fermentation broth was Newtonian and the maximum apparent viscosity (35 cP) was observed at a highly aerated condition (2 vvm). The EPS productivity in an airlift reactor was higher than that in the stirred-tank reactor. The EPS was protein-bound polysaccharides consisted of mainly mannose, xylose, and fructose. The molecular weights of EPS were determined to be $1.3{\sim}1.5{\times}10^6$.

• Journal of the Korean Institute of Gas
• /
• v.16 no.6
• /
• pp.17-22
• /
• 2012

In this study, characteristics of reforming process of Automotive LPG fuel using plasma reactor are investigated. Because plasma reformer technology has advantages of a fast start-up and wide fuel/oxidizer ratio of operation, and reactor size is smaller and more simple compared to typical combustor and catalytic reactor, plasma reforming is suitable to the on-board vehicle reformer. To evaluate the characteristics of the reforming process, parametric effect of $O_2$/C ratio, reactant flow rate and plasma power on the process were investigated. In the test of varying $O_2$/C ratio from partial oxidation stoichiometry to combustion stoichiometry, conversion of LPG was increased but selectivity of $H_2$ decreased. The optimum condition of $O_2$/C ratio for the highest $H_2$ yield was determined to be 0.8~0.9 for 20~50 lpm. The result can be a guide to map optimal condition of reforming process.