• 방송공학회논문지
• /
• 제21권4호
• /
• pp.592-608
• /
• 2016

최근 거의 완벽한 3차원 영상정보를 갖고 있는 디지털 홀로그램에 대한 연구가 활발히 이루어지고 있어 조만간 디지털 홀로그램의 서비스가 시작될 것으로 보인다. 따라서 본 논문에서는 이 서비스에 사용될 수 있는 디지털 홀로그램 동영상을 압축하는 기술을 제안한다. 이 방법은 가장 최근에 국제표준으로 제정된 2차원 동영상 압축 기술인 H.265/HEVC를 사용하는데, 디지털 홀로그램의 화소 간 상관성을 높이기 위하여 도메인 변환 방법을 사용한다. 또한 압축효율을 높이기 위해 H.265/HEVC의 다양한 압축 파라미터들을 고려한다. 본 논문의 목적은 다양한 도메인 변환 방법, 도메인 변환 단위, 압축 파라미터들 중 가장 압축효율이 좋은 최적의 압축조건을 실험을 통하여 구하는 것이다. 이렇게 구해진 조건을 만족하는 압축방법을 기존의 방법들과 비교하여 본 논문에서 제시하는 방법의 우수성을 보인다.

• 한국자동차공학회논문집
• /
• 제13권4호
• /
• pp.145-151
• /
• 2005

Natural gas is one of clean fuels that can replace petroleum-based fuels, because it has low exhaust emission, comparatively high thermal efficiency and abundant deposits. In this addition, owing to high octane number and wide lean flammability limit, it has a strong point to increase the compression ratio. For this reason, the research is being actively executed to increase the generating power and thermal efficiency of the engine by raising the compression ratio through utilization of high octane number relevant to development of CNG engine. In this study, 0.63L single cylinder diesel engine has been used to alter easily compression ratio. Compression ratio has gotten under control by modifying the thickness of gasket between cylinder head and block without major structural modifications. As the result, as compression ratio has increased, generating power and fuel consumption ratio have been improved. As for emission concentration, as compression ratio has increased, THC concentration has been decreased while exhause concentration of NOx increased. In case compression ratio has excessively increased, brake output decrease and cycle variation have been increased. As the result acquired by analyzing brake output, fuel consumption ratio, cycle variation and exhaust, the engine driving condition has acquired $\varepsilon=13$ as the optimal compression ratio in this study.

• Journal of the Korean Wood Science and Technology
• /
• 제44권2호
• /
• pp.204-217
• /
• 2016

Modified poplar has emerged as a potential raw material for furniture production. Lack of specific modified poplar strength information; however, restricts applications in the furniture industry especially as related to strength in corner-joints. Optimization of strength in L-shaped corner dowel modified poplar joints under compression loads utilizing finite element analysis (FEA) by Taguchi method with the focus of this study. Four experiment factors (i.e., Structure Style, Tenon Length, Tenon Diameter, and Tenon Gap), each at three levels, were conducted by adopting a $L_9-3^4$ Taguchi orthodoxy array (OA) to determine the optimal combination of factors and levels for the von Mises stress utilizing ANSYS software. Results of Signal-to-Noise ratio (S/N) analysis and the analysis of variance (ANOVA) revealed the optimal L-shaped corner dowel joint in modified poplar is $45^{\circ}$ Bevel Butt in structure style, 24 mm in tenon length, 6 mm in tenon diameter, and 20 mm in tenon gap. Tenon length and tenon gap are determined to be significant design factors for affecting von Mises Stress. Confirmation tests with optimal levels and experimental test indicated the predicted optimal condition is comparable to the actual experimental optimal condition.

• Elastomers and Composites
• /
• 제47권4호
• /
• pp.341-346
• /
• 2012

사출성형은 고분자성형법 중에서 가장 광범위하게 활용되고 있다. 사출성형은 전형적인 사출성형 외에 가스사출, 물사출, 그리고 사출압축성형 등과 같이 특수한 사출성형방법들이 쓰인다. 사출압축성형은 사출과 압축공정이 합쳐진 것으로 균일한 물성 및 성형의 정밀도를 향상시키기 위하여 사용된다. 또한 사출압축은 잔류응력을 줄이는데도 효과적으로 사용되고 있다. 본 연구에서는 성형품의 형상에 따라 다양하게 나타나는 사출압축성형의 특성에 대해서 컴퓨터 해석을 통해 분석하였다. 성형품에 벽이 있는 제품은 벽의 두께가 압축의 방향과 직각이므로 압축효과가 작게 나타났다. 사출압축성형을 일반사출성형과 비교하였을 때 수축의 균일성 및 수축량 또는 성형수축률이 작게 나타나서 정밀성형에 유리하게 나타났다. 실험계획법을 통해 실제로 제작되고 있는 렌즈에 대해서 최적 사출압축조건을 구하고 이의 결과를 사출성형의 결과와 비교분석하였다.

• 한국지열·수열에너지학회논문집
• /
• 제8권1호
• /
• pp.13-20
• /
• 2012

This is an experimental study on the performance characteristics of effective heat pump in the cooling mode using a single-stage compression $CO_2$ cycle with an IHX(internal heat exchanger). The performance of a single-stage compression with IHX was investigated according to charge amount and operating condition. Moreover, the performance characteristic of cooling operating was analyzed with the length of IHX. As a result, the optimum refrigerant charge amount was 2.2 kg. The optimal system COP for compressor frequency of 30, 40, 50, and 60 Hz was 3.493, 3.228, 2.978, and 2.659, respectively. Since the system with IHX can maintain large cooling capacity regardless of operating condition, the system performance doesn't reduce considerably under unfavorable condition. When the compressor frequency was 40 Hz, the COP for a system with IHX length of 3 m and 5 m was 3.361 and 3.51, respectively. By using the IHX into a $CO_2$ cooling system, the performance and reliability improves simultaneously.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.468-472
• /
• 2005

This paper is to investigate the influence of the endface quality on the loss characteristics of a plastic optical fiber connector for in-car network service. Using the parameters of the surface roughness and applied load, insertion loss of connector is measured. Due to scattering and change of refractive index, an optimal condition for low-loss coupling exists. We present the optimal condition as surface roughness $R_{rms}$ = 8 nm and contact load up to 50 N.

• 한국추진공학회지
• /
• 제18권6호
• /
• pp.1-10
• /
• 2014

극초음속 흡입구를 직관적이며 체계적으로 설계할 수 있는 최적화된 방법을 제시한다. 마하 7의 이론식으로 계산된 극초음속 흡입구는 점성 조건의 전산수치해석을 수행하여 점성에 대한 오차를 보정한다. 전산수치해석을 통한 성능 비교에서 1단 쐐기에 비해 2단 쐐기를 가지는 흡입구 형상이 성능비교에서 좋은 결과를 보였다. 또한 비설계 조건에서 극초음속 흡입구의 성능은 설계 마하수 성능에 비해 손실이 크지 않았다.

• 대한기계학회논문집A
• /
• 제27권4호
• /
• pp.614-622
• /
• 2003

In this paper, the stress-strain curves of bearing steels at hot working conditions are obtained by hot compression test with a computer controlled servo-hydraulic Gleeble 3800 testing machine and elongations and reductions of area of the bearing steels are also obtained by hot tensile test with a Gleeble 1500 testing machine. Experiments are conducted under the various strain-rates and temperatures and their results are used to obtain the flow stress information. A rigid thermo-viscoplastic finite element method is applied to the multi-stage hot forging process in order to predict temperature distribution of workpiece. The experimental results and the analysis results are used to obtain an optimal hot forging condition.

• 한국기계가공학회지
• /
• 제20권8호
• /
• pp.60-66
• /
• 2021

This study aimed at identifying and optimizing the heating-condition parameters that cause surface defects during the compression molding of chalcogenide glass (GeSbSe) lenses through thermal analysis. We derived the optimal heating conditions for molding chalcogenide glass lenses through thermal analysis and analyzed the surface defects. As a result, we observed a significant reduction in surface defects, which verified the analysis process.

• 한국분무공학회지
• /
• 제9권1호
• /
• pp.30-36
• /
• 2004

The purpose of this study was to investigate the fuel spray characteristics that made most important at an homogeneous air fuel mixture, in a common rail direct injection type HCCI engine. As a study conducted relation which a back pressure and injection pressure are influenced to air fuel mixture characteristics, we tried to offer date even through we select suitable to a HCCI engine running condition of the fuel injection condition. To accomplish the study, to measure a injection rate of common rail type injector and to visualize and simulate a fuel spray was conducted. From the result of injection rate, a common rail injector was confirmed to appear a initial delay of 0.3msec and a latter period delay of 0.7msec. Therefore, real injection duration was determined by about 0.5msec increasing. From the result of fuel spray, the spray penetration was proportional to 1/4 exponent of atmosphere pressure. An experimental equation was deduced from the spray penetration of spray visualization experiment and the relation of injection duration and penetration was estimated in HCCI engine using an experimental equation.