• Journal of KIISE:Computer Systems and Theory
• /
• v.26 no.12
• /
• pp.1493-1503
• /
• 1999

ATM Clustering System과 같이 SAN(System Area Network) 환경에서 동작하는 시스템은 낮은 지연시간과 넓은 대역폭의 네트워크가 필수적이나 기존의 에러 복구 프로토콜들은 이러한 요구를 충족시키기에는 큰 오버헤드를 가지고 있다. 제안된 새로운 에러 복구 프로토콜은 ATM Clustering System 환경에서 최적의 성능을 나타내는 light-weight 프로토콜로 에러가 없는 상황과 에러 복구가 진행중인 상황에 따라 acknowledgement 주기를 적응적으로 변화시키는 adaptive acknowledgement scheme를 제안하여 적용하였다. 제안된 프로토콜은 상용 툴인 SDT를 이용한 논리 검증 받았고, DEVSim++ 환경에서의 성능 분석을 통해 프로토콜이 최상의 성능을 보이기 위한 파라메터 값을 찾았고, 이 값을 적용하였을 때의 성능을 기존의 프로토콜과 비교하여 제안된 프로토콜이 더 우수함을 확인하였다.Abstract While a system working with SAN, such as ATM Clustering System, requires a network with low latency and wide bandwidth, the previous error recovery protocols have a serious network overhead to satisfy this requirement. The suggested error recovery protocol is a light-weight protocol which can shows its best performance at ATM Clustering System and uses a newly suggested adaptive acknowledgement scheme. In the adaptive acknowledgement scheme, the period of acknowledgement is dynamically changed depending on the state of the network. We proved the logical correctness of our protocol with SDT and did performance analysis with DEVSim++. From the analysis, we found the optimal parameter values for best performance and showed that our protocol works better than the previous error recovery protocols.

• Journal of Communications and Networks
• /
• v.18 no.5
• /
• pp.744-761
• /
• 2016

For about the past decade and a half research efforts into cognitive radio networks (CRNs) have increased dramatically. This is because CRN is recognized as a technology that has the potential to squeeze the most out of the existing spectrum and hence virtually increase the effective capacity of a wireless communication system. The resulting increased capacity is still a limited resource and its optimal allocation is a critical requirement in order to realize its full benefits. Allocating these additional resources to the secondary users (SUs) in a CRN is an extremely challenging task and integer programming based optimization tools have to be employed to achieve the goals which include, among several aspects, increasing SUs throughput without interfering with the activities of primary users. The theory of the optimization tools that can be used for resource allocations (RA) in CRN have been well established in the literature; convex programming is one of them, in fact the major one. However when it comes to application and implementation, it is noticed that the practical problems do not fit exactly into the format of well established tools and researchers have to apply approximations of different forms to assist in the process. In this survey paper, the optimization tools that have been applied to RA in CRNs are reviewed. In some instances the limitations of techniques used are pointed out and creative tools developed by researchers to solve the problems are identified. Some ideas of tools to be considered by researchers are suggested, and direction for future research in this area in order to improve on the existing tools are presented.

• Korean Institute of Interior Design Journal
• /
• v.27 no.1
• /
• pp.58-67
• /
• 2018

This study aims to analyze the cases of storage space outside housing unit and propose the activation plan. The issue of storage in residential complex has continued to be reported. This is more salient due to the recent preference trend for small houses, the constant increase of living goods and the limitation of the available space inside housing unit. Although more apartment houses are trying to have individual storage in the exterior space to address these issues, there is still a paucity of the related studies and more studies are required. In this study, we conducted on-site investigation and user interview of each case to propose active usage of the storage space outside housing unit. Result of this study shows that the most crucial factor to improve is 'accessibility' in order to activate the storage space. Storage room should be located close to each household or the individual parking space. The second factor is the size and the structure of the storage room. The sufficient space for keeping and taking large objects out are required. The front of the storage room should have a clogged structure to insure privacy. The third is the provision of suitable support programs such as the system that occupants can check remotely what items are in their storage rooms, garage sale, laundry service, auto cleaning system and rental program. Those programs are required for efficient management and activation of space. Another requirement is to improve environmental factors which include maintenance of optimal temperature and humidity, automatic ventilation system, control of individual lights, and security enhancement. Based on the results of the survey, we provide basic data which can be used for practical space planning to activate exterior storage space of the housing unit. Further surveys are required to develop this study by obtaining more data for generalization.

• Journal of Microbiology and Biotechnology
• /
• v.27 no.1
• /
• pp.101-111
• /
• 2017

The task of improving a fungal strain is highly time-consuming due to the requirement of a large number of flasks in order to obtain a library with enough diversity. In addition, fermentations (particularly those for fungal cells) are typically performed in high-volume (100-250 ml) shake-flasks. In this study, for large and rapid screening of itaconic acid (IA) high-yielding mutants of Aspergillus terreus, a miniaturized culture method was developed using 12-well and 24-well microtiter plates (MTPs, working volume = 1-2 ml). These miniaturized MTP fermentations were successful, only when highly filamentous forms were induced in the growth cultures. Under these conditions, loose-pelleted morphologies of optimum sizes (less than 0.5 mm in diameter) were casually induced in the MTP production cultures, which turned out to be the prerequisite for the active IA biosynthesis by the mutated strains in the miniaturized fermentations. Another crucial factor for successful MTP fermentation was to supply an optimal amount of dissolved oxygen into the fermentation broth through increasing the agitation speed (240 rpm) and reducing the working volume (1 ml) of each 24-well microtiter plate. Notably, almost identical fermentation physiologies resulted in the 250 ml shake-flasks, as well as in the 12-well and 24-well MTP cultures conducted under the respective optimum conditions, as expressed in terms of the distribution of IA productivity of each mutant. These results reveal that MTP cultures could be considered as viable alternatives for the labor-intensive shake-flask fermentations even for filamentous fungal cells, leading to the rapid development of IA high-yield mutant strains.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.57 no.2
• /
• pp.93-101
• /
• 2015

The purpose of this study is to evaluate the paddy irrigation efficiency using real-time water level monitoring data and intermittent irrigation model in Gimjae, Dong-Jin irrigation district. For this study, the real-time water level data in Gimjae main canal and other secondary canals were collected from 2012 to 2014 and converted to daily discharge using rating curve in each canal. From intermittent irrigation model in paddy, irrigation water requirement was estimated and irrigation efficiency was calculated. The average amount of irrigation water supply per unit irrigation area was 1,011 mm in Gimjae main canal for 12,749 ha irrigation area, 1,011 mm in the secondary canal of upper region and 1,470 mm in the secondary canal of lower region. The median irrigation loss was 43 % in Gimjae main canal, 25 % in secondary canal of upper region and 35 % in the secondary canal of lower region. The larger irrigation area is, the irrigation loss rates tend to decrease in secondary canals. Monthly median irrigation losses in upper region were 10 (June) - 40 % (September) and those in lower region were 25 (May) to 40 % (April, June, August, and September). The results of canal management loss can be available as the basic data for irrigation water management and estimating guideline of optimal irrigation water supply to improve agricultural water use efficiencies.

• Asian-Australasian Journal of Animal Sciences
• /
• v.13 no.10
• /
• pp.1399-1406
• /
• 2000

A continuous culture study was conducted to determine the impact of ruminal degradable soy protein (S-RDP) level and dilution rate (D) on growth of ruminal non-structural carbohydrate-fermenting microbes. Corn starch, urea and isolated soy protein (ISP) were used to formulate three diets with S-RDP levels of 0, 35 and 70% of total dietary CP. Two Ds were 0.03 and $0.06h^{-1}$ of the fermenter volume in a single-effluent continuous culture system. As S-RDP levels increased, digestibilities of dietary dry matter (DM), organic matter (OM) and crude protein (CP) linearly (p=0.001) decreased, whereas digestion of dietary starch linearly (p=0.001) increased. Increasing D from 0.03 to $0.06h^{-1}$ resulted in decreased digestibilities of dietary DM and OM, but had no effect on digestibilities of dietary starch (p=0.77) and CP (p=0.103). Fermenter pH, the concentration of volatile fatty acids (VFA) and daily VFA production were unaffected (p=0.159-0.517) by S-RDP levels. Molar percentages of acetate, propionate and butyrate were greatly affected by S-RDP levels (p=0.016-0.091), but unaffected by D (p=0.331-0.442). With increasing S-RDP levels and D, daily bacterial counts, daily microbial N production (DMNP) and microbial efficiency (MOEFF; grams of microbial N produced per kilogram of OM truly digested) were enhanced (p=0.001). The increased microbial efficiency with increasing S-RDP levels is probably the result of peptides or amino acids that served as a stimulus for optimal protein synthesis. The quantity of ruminal degradable protein from soy proteins required for optimum protein synthesis of non-structural carbohydrate-fermenting microbes appears to be equivalent to 9.5% of dietary fermented OM.

• Asian-Australasian Journal of Animal Sciences
• /
• v.21 no.12
• /
• pp.1794-1799
• /
• 2008

This preliminary feeding trial was conducted to study the effects of different dietary selenium (Se) levels on growth performance and toxicity in juvenile black seabream, Acanthopagrus schlegeli (Bleeker). Fish averaging $7.0{\pm}0.1g$ ($mean{\pm}SD$) were fed one of the five semi-purified diets containing 0.21, 0.30, 0.52, 1.29 and 12.3 mg sodium selenite ($Na_2SeO_3$)/kg diet (Se 0.21, Se 0.30, Se 0.52, Se 1.29 or Se 12.3) for 15 weeks. After the feeding trial, weight gain (WG), feed efficiency (FE), specific growth rate (SGR) and protein efficiency ratio (PER) of fish fed Se 0.21, Se 0.30, Se 0.52 and Se 1.29 diets were not significantly different, however fish fed Se 12.3 diet showed significantly lower WG, FE, SGR and PER than those of fish fed the other diets (p<0.05). Fish fed Se 0.21, Se 0.30, Se 0.52, Se 1.29 and Se 12.3 diets showed no significant differences in hematocrit (PCV), hemoglobin (Hb) and red blood cells (RBC), however fish fed Se 12.3 diet showed lower values of PCV, Hb and RBC than those of fish fed the other diets. Histopathological lesions such as tubular necrosis and polycystic dilation of tubules in the kidney tissues were observed in fish fed Se 12.3 diet. Se was accumulated in a dose-dependent manner in the liver, kidney, muscle and gill tissues. Based on the results of this preliminary feeding trial, a dietary Se level of 0.21 mg $Na_2SeO_3/kg$ diet could be optimal for proper growth performances, and a dietary Se level of 12.3 mg $Na_2SeO_3/kg$ diet may ultimately be toxic to juvenile black seabream, Acanthopagrus schlegeli.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.13 no.1
• /
• pp.35-43
• /
• 2015

A large amount of radioactively-contaminated gravel can be produced on the demolition/restoration of facilities related the back end of fuel cycle. However, because of the lacking in basic knowledge for decontamination of radioactive-contami-nated gravel, this study has performed the basic tests using for soil-washing. To find effective decontamination condition, several experiments were carried out for the selection of optimal decontamination agents. Washing by 0.1 M nitric acid was proved to be more effective than that by distilled water or surfactant for decontamination of uranium-contaminated gravel. In addition, crushing/grinding of uranium-contaminated gravel prior to washing was contributed to increase in of removal efficiency of uranium and reduction of decontamination time. The smaller the sizes of crushed gravel was, the more the removal efficiency increased. Also, small the sized particles improved chances for meeting the clearance requirement of the treated gravel.

• Geomechanics and Engineering
• /
• v.14 no.5
• /
• pp.467-477
• /
• 2018

Estimation of hydraulic parameters is a critical step during design of foundation dewatering works. When many piles are installed in an aquifer, estimation of the hydraulic conductivity should consider the blocking of groundwater seepage by the piles. Based on field observations during a dewatering project in Shanghai, hydraulic conductivities are back-calculated using a numerical model considering the actual position of each pile. However, it is difficult to apply the aforementioned model directly in field due to requirement to input each pile geometry into the model. To develop a simple numerical model and find the optimal hydraulic conductivity, three scenarios are examined, in which the soil mass containing the piles is considered to be a uniform porous media. In these three scenarios, different sub-regions with different hydraulic conductivities, based on either automatic inverted calculation, or on effective medium theory (EMT), are established. The results indicate that the error, in the case which determines the hydraulic conductivity based on EMT, is less than that determined in the automatic inversion case. With the application of EMT, only the hydraulic conductivity of the soil outside the pit should be inverted. The soil inside the pit with its piles is divided into sub-regions with different hydraulic conductivities, and the hydraulic conductivity is calculated according to the volume ratio of the piles. Thus, the use of EMT in numerical modelling makes it easier to consider the effect of piles installed in an aquifer.

• Proceedings of the Korea Contents Association Conference
• /
• 2007.11a
• /
• pp.27-29
• /
• 2007

The visual implementation of 3-dimensional national environment is focused by the requirement and importance in the fields such as, national development plan, telecommunication facility deployment plan, railway construction, construction engineering, spatial city development, safety and disaster prevention engineering. The currently used DEM system using contour lines, which embodies national geographic information based on the 2-D digital maps and facility information has limitation in implementation in reproducing the 3-D spatial city. Moreover, this method often neglects the altitude of the rail way infrastructure which has narrow width and long length. There it is needed to apply laser measurement technique in the spatial target object to obtain accuracy. Currently, the LiDAR data which combines the laser measurement skill and GPS has been introduced to obtain high resolution accuracy in the altitude measurement. In this paper, we first investigate the LiDAR based researches in advanced foreign countries, then we propose data a generation scheme and an algorithm for the optimal manage and synthesis of railway facility system in our 3-D spatial terrain information. For this object, LiDAR based height data transformed to DEM, and the realtime unification of the vector via digital image mapping and raster via exactness evaluation is transformed to make it possible to trace the model of generated 3-dimensional railway model with long distance for 3D tract model generation.