• Nuclear Engineering and Technology
• /
• v.26 no.4
• /
• pp.536-547
• /
• 1994

The state feedback optimal control techniques are used in designing the reactor control system. The mathematical plant model with the temperature feedback effects is established from the one delayed neutron group point kinetics equation and the singly lumped thermal-hydraulic balance equations, and is expressed in terms of state variables. The LQR (Linear Quadratic Regulator) control system is designed, being followed by the LQG (Linear Quadratic Gaussian) design to determine the optimal conditions of rod movement for the desired reactor power responses. And two different servo control schemes, the ordinary feedback system and the order increased regulating system, are proposed for the purpose of input tacking. The general control characteristics such as stability margins and output responses are discussed. Comparing each other, it is found that the order increased regulating system has far better control characteristics than the ordinary feedback system.

• Journal of the Ergonomics Society of Korea
• /
• v.18 no.2
• /
• pp.57-69
• /
• 1999

The primary objective of this research was to suggest the design dimensions of automotive seating package that has an important effect upon seating package design. To conduct the research, a set of manikin dimensions that are representative for Korean was determined by using a statistical scheme. With these dimensions, we generated nine manikins for male and female, respectively. Also, the preferred driving posture was investigated using the experimental setup. To find each joint angle for subjects, a driving monitoring system was developed and a three dimensional motion analysis system was employed. The joint angle for the subject was established and compared with related literature. With the generated manikins and each joint angle, the driving posture was simulated by using SAFEWORK that is a program to generate manikins. The positions and adjustable ranges from the accelerator heel point to the hip point and the steering wheel center point that are important variables in order to design seating package were suggested. Further research is needed to determine the seating package dimensions three dimensionally.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.25 no.4
• /
• pp.15-25
• /
• 2000

In this paper, we introduce a point-to-multipoint minimum cost flow problem with convex and demand splitting. A source node transmits the traffic along the tree that includes members of the point-to-multipoint connection. The traffic is replicated by the nodes only at branch points of the tree. In order to minimize the sum of arc costs, we assume that the traffic demand can be splitted and transmitted to destination nodes along different trees. If arc cost is linear, the problem would be a Steiner tree problem in networks eve though demand splitting is permitted. The problem would be applied in transmitting large volume of traffic from a serve to clients in Internet environments. Optimality conditions of the problem are presented in terms of fair tree routing. The proposed algorithm is a finite terminating algorithm for $\varepsilon$-optimal solution. convergence of the algorithm is obtained under monotonic condition and strict convexity of the cost function. Computational experiences are included.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.10
• /
• pp.1726-1730
• /
• 2008

In this paper, the application schemes for coordinated control system of multiple FACTS were presented to enhance the voltage stability around the metropolitan areas. In order to coordinated control of FACTS devices, f-V analysis method which is one of the indices for voltage stability was performed with real time network data which is transferred from SCADA/EMS system. If the system is unstable after contingencies, the new operation set-point of FACTS would be determined using bus sensitivity from tangent vector at voltage instability point. Otherwise, we would determine the new operation set-point of FACTS for considering economical operation, like as active power loss minimization using Optimal Power Flow algorithm. In simulation, the SCADA/EMS 2007's data are used for studying the coordinated control algorithm of multiple FACTS devices that is installed or will be installed in KOREA power system

• Journal of the Korean Society for Precision Engineering
• /
• v.8 no.2
• /
• pp.47-56
• /
• 1991

The specifications needed for the mobile cranes are summarized as the following : 1) there may be not occured the oscillation of the cargo at unloading point. 2)the required time from departure point to destination point may be as short as possible. 3) there may be not a collapse of cargo caused by the oscillation in the course that the crago is mobilling. In this paper, the linear fractional transformation method is adopted as a method in order to improve the above mentioned problems. A design method of servo system is developed by modifying Davison's method for the case that the homogeneous differential equations of reference input and disturbance are different types. The real time control of a mobile crane system is implemented by 16bits microcomputer with A/D and D/A converters to illustrate the application of the adopted method. The experimental results for the three types of the design methods; linear fractional transformation method, servo system design method and optimal control method are shown for the comparison.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.7
• /
• pp.923-929
• /
• 2021

TCP communication and packet communication require transmission control technology to ensure high quality and high reliability. However, in the case of real-time data transmission, an inefficient transmission problem occurs. In order to overcome this problem and transmit the packet reliability, in general, early congestion control using the buffer level as an index was used. Control of the congestion control point and the cancellation point is delayed because the point at which congestion is controlled is based on the buffer level. Therefore, in this paper, not only the buffer level indicator, but also the ideal buffer level, which determines the packet discard probability, is classified so that the transmission rate and buffer level that measure network congestion are close to the level above the optimal setting. As a result, it was shown that the average buffer level can be directly controlled by maintaining the average buffer level by the ideal buffer level set in the experiment to prove the proposed method.

• Journal of Biosystems Engineering
• /
• v.29 no.6 s.107
• /
• pp.515-520
• /
• 2004

A device far estimating the optimal artificial insemination time consisted of a computer, RS module, and six direct-reflex photo-sensors. Program was written in LabWindows CVI. In order to establish references for estimating optimal artificial insemination time, lying rate of the thirty three $Berkshire{\times}Hampshire crossbred sows (parity 5 to 6) was recorded from 2 days after moving into stalls to artificial insemination using a time lapse VCR and was measured every hour with one minute interval using the scan point sampling method. Twenty low hours in a day were divided into three comparing periods : 21:00 to 06:59, 07:00 to 13:59, and 14:00 to 20:59. If sum of the percentages of tying during a comparing period was less than the reference value, the starting hour of the comparing period was considered as onset of estrus and the optimal artificial insemination time was estimated at 20 to 24 hours after onset of estrus. The experimental device was evaluated with twenty five $Berkshire{\times}Hampshire$ crossbred sows (parity 2 to 7) and 23 of 25 sows $(92\%)$ were pregnant. This result suggests that the experimental device is excellent in performance for estimating optimal artificial insemination time.

• Journal of the Korean Home Economics Association
• /
• v.47 no.4
• /
• pp.61-72
• /
• 2009

The purpose of this research is to suggest a new way to approach measuring the waist line of slacks. The pattern formulated enables a construction method that optimizes motion. The method is based on the measurement on the length change of the body surface line. The research reveals: 1. The analysis of expansion and contraction by area showed that G8 markedly shrunk, whilst G15 maximally stretched during M4 motion. 2. The areas that stretched during M2 motion were, in order of size: G10, G17, G16, and G8. Conversely, the areas that shrunk are, in order, G9, G11, and G18. The areas that stretched during M3 motion were G10, G17, G16, G12, and G15; the areas that shrunk were G9, G11, G18, and G8. 3. In constructing the slacks pattern to allow for appropriate movement, we calculated the length between the knee and back of the waist, point (y), using Pythagoras’theorem and trigonometry. The equation was y = 1.005x. 4. In the two pattern N method and L method, y is equal or less than x, but for our research pattern, y was larger than x

• International conference on construction engineering and project management
• /
• 2020.12a
• /
• pp.3-12
• /
• 2020

Nowadays, as-is BIM generation has been popularly adopted in the architecture, engineering, construction and facility management (AEC/FM) industries. In order to generate a 3D as-is BIM of a structural component, current methods require a registration process that merges different sets of point cloud data obtained from multiple locations, which is time-consuming and registration error-prone. To tackle this limitation, this study proposes a registration-free 3D point cloud data acquisition technique for as-is BIM generation. In this study, small-size mirrors that rotate in both horizontal and vertical direction are used to enable the registration-free data acquisition technique. First, a geometric model that defines the relationship among the mirrors, the laser scanner and the target component is developed. Second, determinations of optimal laser scanner location and mirror location are performed based on the developed geometrical model. To validate the proposed registration-free as-is BIM generation technique, simulation tests are conducted on key construction components including a PC slab and a structural wall. The result demonstrates that the registration-free point cloud data acquisition technique can be applicable in various construction elements including PC elements and structural components for as-is BIM generation.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.5
• /
• pp.897-903
• /
• 2010

This paper presents a response surface method(RSM) with Latin Hypercube Sampling strategy, which is employed to optimize a magnet pole shape of large scale BLDC motor to minimize the cogging torque. The proposed LHS algorithm consists of the multi-objective Pareto optimization and (1+1) evolution strategy. The algorithm is compared with the uniform sampling point method in view points of computing time and convergence. In order to verify the developed algorithm, a 6 MW BLDC motor is simulated with 4 design parameters (arc length and 3 variables for magnet) and 4 constraints for minimizing of the cogging torque. The optimization procedure has two stages; the fist is to optimize the arc length of the PM and the second is to optimize the magnet pole shape by using the proposed hybrid algorithm. At the 3rd iteration, an optimal point is obtained, and the cogging torque of the optimized shape is converged to about 14% of the initial one. It means that 3 iterations aregood enough to obtain the optimal design parameters in the program.