• Journal of Drive and Control
• /
• v.15 no.2
• /
• pp.9-21
• /
• 2018

The aim of this study was to develop and test a model of an auto-sensing hydraulic breaker that can automatically change its 4-step impact mode according to the rock strength using SimulationX. The auto-sensing hydraulic breaker with a 4-step variable impact mode has the advantage of obtaining optimal impact energy and impact frequency under various rock conditions compared to an auto-sensing hydraulic breaker with a 2-step variable impact mode, which has already been developed overseas. Several steps were necessary to conduct this study. First, the operation principle of the auto-sensing hydraulic breaker with the 2-step variable impact mode was analyzed. Based on the findings, an analysis model of the auto-sensing hydraulic breaker with the 4-step variable impact mode was developed (and compared with the 2-step variable impact mode) Finally, an analysis of the results established that the stepwise variable of the impact mode was implemented according to the rock strength and the difference of each impact mode was confirmed. This study is expected to contribute to the development of auto-sensing hydraulic breakers that are superior to those developed by advanced companies in foreign countries.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.8
• /
• pp.40-47
• /
• 2010

In this paper, we propose a probability method to determine minimum capacity of energy storage system(ESS) for Micro Grid(MG). Because of high capital cost of ESS, it's very important to determine optimal capacity of ESS and for stable operation of MG and we should determine minimum capacity of ESS. The proposed method has abilities to consider forced outage rate of generators and intermittent of non-dispatchable generators and minimum capacity make MG keep energy balancing by oneself.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.12
• /
• pp.2816-2822
• /
• 2014

In this paper, a wideband loop antenna for UWB applications is studied. The structure of the proposed wideband loop antenna is a circular loop antenna with appended circular sectors to obtain an ultra-wideband characteristic. The circular sectors are used instead of conventional triangular sectors to match with the 50 ohm feed line. Optimal design parameters are obtained by analyzing the effects of the gap between the circular sectors and the radius of the circular loop on the input reflection coefficient and gain characteristics. The optimized wideband loop antenna is fabricated on an FR4 substrate with a dimension of 41 mm by 41 mm. Experiment results show that the proposed antenna has a frequency band of 3.1-11.0 GHz for a VSWR < 2.25, which assures the operation in the UWB band. Measured gain ranges 1.3-5.3 dBi in the UWB band.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.10
• /
• pp.1845-1851
• /
• 2016

In this paper, a design method for a wideband square loop antenna for Digital TV applications is studied. The proposed loop antenna is a square loop antenna combined with circular sectors to connect with central feed points. The square loop is used instead of the circular loop in order to miniaturize the antenna size. The input reflection coefficient and gain characteristics of the proposed antenna are analyzed to match with the 75 ohm port impedance for DTV applications. The effects of the gap between the circular sectors and the length of the square loop on the input reflection coefficient and gain characteristics are examined to obtain the optimal design parameters. The optimized antenna is fabricated on an FR4 substrate, and the experiment results show that it operates in the frequency band of 470-1,300 MHz for a VSWR < 2, which assures the operation in the DTV band.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.7
• /
• pp.462-468
• /
• 2018

The piezoelectric energy harvesting characteristics of a trapezoidal cantilever generator with lead zirconate titanate (PZT) laminate were investigated with various Ag inner electrodes. The piezoelectric mode of operation was a transverse mode by using a planar electrode pattern. The piezoelectric cantilever generator was fabricated using trapezoidal cofired-PZT/Ag laminates by five specimens of 2, 3, 4, 7, and 13 layers of Ag. As the number of Ag electrodes increased, impedance and output voltage at resonant frequency significantly decreased, and capacitance and output current showed an increasing tendency. A maximum output power density of $7.60mW/cm^3$ was realized for the specimen with seven Ag layers in the optimal condition of acceleration (1.2 g) and resistive load ($600{\Omega}$), which corresponds to a normalized power factor of $5.28mW/g^2{\cdot}cm^3$.

• Journal of the Korean Institute of Gas
• /
• v.16 no.2
• /
• pp.38-44
• /
• 2012

In recent years, the need for more fuel-efficient and lower-emission vehicles has driven the technical development of alternative fuels such as LPi (Liquid phase LPG injection) which uses pump for the high pressure supply of liquid LPG fuel and is able to meet the limits of better emission levels while it has an advantage of higher power. Although it has the advantage of power and lower emission levels, the characteristics of LPG, such as high vapor pressure, lower viscosity and surface tension than gasoline fuels makes it difficult design system. Therefore most fuel pumps and injectors are imported. In the present study, in order to domestically develop LPG injector which guarantees flow rates and optimal operation, the experimental investigation on leakage and flow rate characteristics of developed prototype injector was carried out at the bench test rig for developed injector.

• IE interfaces
• /
• v.23 no.4
• /
• pp.311-318
• /
• 2010

In the daily multi-reservoir operating problem, monthly storage targets can be used as principal operational guidelines. In this study, we tested the use of a simple back-propagation Artificial Neural Network (ANN) model to derive monthly storage guideline for daily Coordinated Multi-reservoir Operating Model (CoMOM) of the Han-River basin. This approach is based on the belief that the optimum solution of the daily CoMOM has a good performance, and the ANN model trained with the results of daily CoMOM would produce effective monthly operating guidelines. The optimum results of daily CoMOM is used as the training set for the back-propagation ANN model, which is designed to derive monthly reservoir storage targets in the basin. For the input patterns of the ANN model, we adopted the ratios of initial storage of each dam to the storage of Paldang dam, ratios of monthly expected inflow of each dam to the total inflow of the whole basin, ratios of monthly demand at each dam to the total demand of the whole basin, ratio of total storage of the whole basin to the active storage of Paldang dam, and the ratio of total inflow of the whole basin to the active storage of the whole basin. And the output pattern of ANN model is the optimal final storages that are generated by the daily CoMOM. Then, we analyzed the performance of the ANN model by using a real-time simulation procedure for the multi-reservoir system of the Han-river basin, assuming that historical inflows from October 1st, 2004 to June 30th, 2007 (except July, August, September) were occurred. The simulation results showed that by utilizing the monthly storage target provided by the ANN model, we could reduce the spillages, increase hydropower generation, and secure more water at the end of the planning horizon compared to the historical records.

• Industrial Engineering and Management Systems
• /
• v.15 no.4
• /
• pp.396-402
• /
• 2016

In this study, hydraulic analysis of water-supply networks in Marivan was performed by modeling. WATERGEMS was used for modeling and it was calibrated using existing rules and regulations. The purpose of this research is modeling urban water network and its analysis based on hydraulic criteria and meeting pressure conditions at the nodes and complying the economic speed. To achieve this goal, first the pipelines of city streets was designed in AutoCAD on a map of the city. It should be mentioned that it was tried to prevent from creating additional loops in the network and the optimal network was designed by a combination of annular and branch loops. In the next step, the pipes were called in WATERGEMS and then we continue the operation by the allocation of elevation digits to the pipes. Since the topography of this city is very specific and unique, the number of pressure zones was increased. Three zones created only covers about 20% of the population in the city. In this dissertation, the design was performed on the city's main zone with the largest density in the Figures 1,320-1,340. In the next step, the network triangulation was conducted. Finally, the Debiw as allocated based on the triangulation conducted and considering the density of the city for year of horizon. Ultimately, the network of Marivan was designed and calibrated according to hydraulic criteria and pressure zoning. The output of this model can be used in water-supply projects, improvement and reform of the existing net-work in the city, and various other studies. Numerous and various graphs obtained in different parts of a network modelled can be used in the analysis of critical situation, leakage.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.2
• /
• pp.648-658
• /
• 2018

Regarding the fact that wind power forecast accuracy is gradually improved as time is approaching, this paper proposes a two-stage rolling dispatch approach based on model predictive control (MPC), which contains an intra-day rolling optimal scheme and a real-time rolling base point tracing scheme. The scheduled output of the intra-day rolling scheme is set as the reference output, and the real-time rolling scheme is based on MPC which includes the leading rolling optimization and lagging feedback correction strategy. On the basis of the latest measured thermal unit output feedback, the closed-loop optimization is formed to correct the power deviation timely, making the unit output smoother, thus reducing the costs of power adjustment and promoting wind power accommodation. We adopt chance constraint to describe forecasts uncertainty. Then for reflecting the increasing prediction precision as well as the power dispatcher's rising expected satisfaction degree with reliable system operation, we set the confidence level of reserve constraints at different timescales as the incremental vector. The expectation of up/down reserve shortage is proposed to assess the adequacy of the upward/downward reserve. The studies executed on the modified IEEE RTS system demonstrate the effectiveness of the proposed approach.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.05a
• /
• pp.263-266
• /
• 2017

Numerous maritime safety technologies and systems are being developed to support safe navigation at Sea. e-Navigation is a representative system for maritime safety. It is being developed to maximize the ships safety by applying most maritime safety technologies. The e-Navigation system is being developed by the International Maritime Organization (IMO) with the aim of introducing it by 2019. South Korea has already recognized the importance of maritime safety support technology and is actively introducing e-Navigation. Korean e-Navigation is being designed to provide diverse functions for maritime safety, such as providing an optimal safe route, risk analysis, and weather information. Service modules that provide e-Navigation's each function use different types of data that are difficult to configure as a single database. In this paper, we analyze the data needed for Korean e-Navigation, the data service system structure and types that can effectively support it.