• The Korean Journal of Ceramics
• /
• 제5권3호
• /
• pp.296-302
• /
• 1999

The state of the art of the 2-stage swirl calciner is to make 2-stage counter gas flow in a calciner with cooler hot air. Gas flow in the calciner increases retention time of raw mix particles. Simple structure of the 2-stage swirl calciner operated optimally the rotary cement kiln. In this study, in order to decide the entrance type of the cooler air of the optimal calciner model, an entrance cooler air velocity, the input points of raw mix were analyzed in many aspects with cold model experiment and computational fluidized dynamic simulation. It was found that the entrance type of cooler air fully splite 2-stage for the optimal condition of the cold model calciner. The operation conditions were that the input feeding, the cooler air velocity and the air velocity of throat were 0.33kg/$\textrm m$3$, 15m/s and 20m/s respectively. The performance of 150 t/d the pilot plant connected with the kiln rising duct was that volume capacity of the calciner is over 430 kg/$\textrm m$3$-h, decarbonation rate of raw mix apparently 90%, heat consumption 950 kcal/kg-cli and retention time of raw mix 2.4 sec. Its the best operating condition is cooler air velocity 18m/s, the gas velocity of throat 25m/s, feeding rate of raw mix 10t/h. The operating experience of the pilot plant confirmed the success of scale up for over 3000 t-cli/d.

• 한국패류학회지
• /
• 제17권2호
• /
• pp.95-104
• /
• 2001

To determine optimal conditions for measurement of the clearance rate in feeding experiment of an intertidal bivalve Glauconome chinensis, effects of starvation, extent of mixing at subsampling, and initial prey concentration were assessed. Experiments were conducted separately for each condition with different treatments. Two-way ANOVAs showed that there were significant differences in clearance rates among different starvation periods (p<0.001), extents of mixing (p = 0.005), and prey concentrations (p < 0.001). Starvation for 1 or 2 days gave rise to 2 to 3-fold increase in the clearance rate. After starvation for 5 days, the clearance rate decreased seriously, implying loss of physiological status. It is suggested that animals should be fed during acclimation. The differences of the clearance rates between gentle and vigorous mixings were significant, but the differences were smaller than that among different incubation times. It was found that vigorous mixing is not necessary. The effect of initial prey concentration was great. However, optimal prey concentration could not be determined at any fixed value. Experiments with multiple concentrations of algal prey are recommended. Optimal incubation time for measurement of the clearance rate of G. chinensis was determined to be 2-4 hours.

• 생명과학회지
• /
• 제14권1호
• /
• pp.167-173
• /
• 2004

Lactobacillus brevis BH-21의 균체를 고정화하여 column형 reactor를 이용하여 $\gamma$-aminobutyric acid의 연속적 생산을 검토하였다. Lactobacillus brevis BH-21에 의한 $\gamma$-aminobutyric acid 생산조건은 고정화 담체로는 3.0% sodium alginate가 좋았고 직경 2.2 mm의 bead를 사용하여 기질의 주입속도는 10 mL/h이 최적 조건이었다. Lactobacillus brevis BH-21의 고정화 균체와 유리 균체를 사용하여 $\gamma$-aminobutyric acid의 생산을 최적 조건하에서 1, 2, 3, 및 4차 발효 동안 48시간마다 신선한 기질을 주입하면서 비교ㆍ조사한 결과 고정화 균체를 사용 시에 생산량이 더 많았다. Column형 reactor에 의한 연속 발효 시 발효 25일까지 생산이 우수하였고 발효 30일까지는 $\gamma$-aminobutyric acid를 생산할 수 있었다.

• 한국환경보건학회지
• /
• 제21권4호
• /
• pp.49-55
• /
• 1995

Dyes are released into the environment as industrial wasterwater. Dyes are considered to be a pollution problem because of the wide spread into environment with a variety of colors. Continuous biodegradation of reactive dyes such as Rifacion Red H-3EB, Rifazol Blue BT, Rifacion Yellow P4G and Rifacion Brown RT were demonstrated using multistage rotating disc contactor immobilized by Aspergillus sojae B-10. Aspergillus sojae B-10 was cultivated the optimal medium containing 2.0% glucose, 0.08% $NaNO_3$, 0.1% $KH_2PO_4$ and 0.5% $MgSO_4\cdot 7H_2O$, pH 5 at 32$\circ$C. Mycelium of Aspergillus sojae B-10 were guck to the rotating disc for 10 days until steady state. For continuous biodegradation of reactive dyes by using rotating disc contactor, it was most effective biodegradation in the medium containing 1,000 ppm each dyes at the medium feeding rate of 20 ml per hour. Under the conditions biodegradation of each dyes on 2, 4 and 6 days were 20~50%, 75% and 96%, respectively. Therefore, practical application of reactive dyes were carried out at the feeding rate of 20 ml/h as synthetic wasterwater containing 500 ppm of mixture reactive dyes. It was found the highest levels of 94% biodegradation during 20 days.

• 한국수정란이식학회지
• /
• 제14권2호
• /
• pp.83-88
• /
• 1999

This study was undertaken with three objectives : to determine the optimal time of blood collection for plasma urea nitrogen(PUN) analysis, to examine the frequency distribution of PUN levels in recipient herd and to relate concentration of PUN to conception rate in Hanwoo recipients. The relationship between PUN level and time postfeeding was examined for 5 individual cows. Mean concentration of PUN rose for 4hrs postfeeding and decreased to PUN level before feeding at 10hrs postfeeding. And then, the blood for PUN analysis was collected at the time before feeding in next experiments. The ratio of cows with PUN concentration of < 12, 12∼18 and 18mg/dl were 50.6, 39.9 and 9.5% in 163 recipients, individually. The pregnancy rate of cows with PUN concentration 12∼16 mg/dl (63.3%) was higher than that of cows with PUN concnetration < 12 mg/dl (46.7%) or > 16mg/dl (42.9%). There results suggest that the PUN test may be beneficial for management of recipient herd in effects to maintain or improve reproductive efficiency.

• 상하수도학회지
• /
• 제31권4호
• /
• pp.273-279
• /
• 2017

Optimal processes to remove chromaticity at E water treatment plant(WTP) mainly caused by algae of E lake in Jeju island were investigated based on lab-tests of chlorine and ozone oxidation. 42.9% of chromaticity of filtered water was removed by chlorine oxidation under pH 7.0~8.0, dose of 1.0 mg/L with contact time of 30~60 min. On the other hand, chromaticity removal was 71.4% when post-ozone dose of 0.9~1.9 mg/L and pH 9.0, while it was increased to 86.7% under post-ozone dose of 3.1~7.3 mg/L and pH 9.0. However, there was no significant chromaticity removal efficiency increase when ozone doses were higher than 5.0 mg/L regardless of feeding point(i.e., pre-ozonation and post-ozonation) and pHs(i.e., 7.0 and 9.0.) under the experimental conditions. Based on the results, chlorine oxidation using existing chlorination facilities at the WTP is recommended for lower chromaticity while ozone oxidation is recommended for higher chromaticity by installing new ozone feeding facilities.

• Journal of Microbiology and Biotechnology
• /
• 제12권4호
• /
• pp.687-691
• /
• 2002

To enhance the production of flavonoids [baicalin, wogonin-7-Ο-glucuronic acid (GA)], which are secondary metabolites of Scutellaria baicalensis Georgi(G.) plant cells, a multilayer perceptron control system was applied to regulate the substrate feeding in a fed-batch cultivation. The optimal profile for the substrate feeding rate in a fed-batch culture of S. baicalensis G. was determined by simulating a kinetic model using a genetic algorithm. Process variable profiles were then prepared for the construction of a multilayer perceptron controller that included massive parallelism, trainability, and fault tolerance. An error back-propagation algorithm was applied to train the multiplayer perceptron. The experimental results showed that neurocontrol incorporated with a genetic algorithm improved the flavonoid production compared with a simple fuzzy logic control system. Furthermore, the specific production yield and flavonoid productivity also increased.

• 한국생산제조학회지
• /
• 제18권6호
• /
• pp.585-589
• /
• 2009

Extruder is divided to greatly three part at extrusion process. First, by hopper(Hopper) second, barrel(Barrel) with Screw that is point of extruder and third that is raw material supply wealth extrusion into dies(DIES) Part that decide shape of do product greatly divide. Hopper is role that distribute in raw material supply wealth (Feeding zone) of Screw preserving raw material in state of high quality how at extrusion process, and make distributed raw material as Screw in barrel rotates and 3 stage and inflicting heat and pressure raw material melting(Melting) state. And raw material of melting state Screw's measuring stoker(Metering zone) whereabouts anaphora do and product is completed through pipe channel of dies. Dies that is the most important as Screw in extrusion is part that is last part of melting state process of raw material and causes huge effect in quality of product. If more than design of dies happens, manufacture itself of dies is hard, but there are a lot of amount of losses accordingly. In this research, make pipe channel that raw material of melting state flows in dies can present dies basic design method through flow analysis of ideal pipe channel using CFdesign.

• Membrane and Water Treatment
• /
• 제10권2호
• /
• pp.127-137
• /
• 2019

The D2EHPA/TBP co-extractants immobilized PolyHIPE membrane can be used for the selective separation of Mn (II) from Co (II). By solvent-nonsolvent method, D2EHPA/TBP co-extractants can be effectively immobilized into PolyHIPE membrane. The pore structure of PolyHIPE membrane and the presence of TBP enhance the stability of immobilized co-extractants. The optimal operating conditions for the separation of Mn (II) and Co (II) are feeding phase at pH 5.5, sulfuric acid concentration in the stripping phase of about 50 g/L and stirring speed at 400 rpm. The D2EHPA/TBP co-extractants ratio of 5:1 shows synergetic effect on Mn/Co separation factor about 22.74. The removal rate and recovery rate of Mn (II) is about 98.4 and 97.1%, respectively, while for Co (II) the transport efficiency is insignificant. The kinetic study of Mn (II) transport shows that high initial flux, $J_f^o=80.1({\mu}mol/m^2s)$, and maxima stripping flux, $J_s^{max}=20.8({\mu}mol/m^2s)$, can be achieved with D2EHPA/TBP co-extractants immobilized PolyHIPE membrane. The stability and reusability study shows that the membrane can maintain a long term performance with high efficiency. High purity of Co (II) and Mn (II) can be recovered from the feeding phase and stripping phase, respectively.

• Animal Bioscience
• /
• 제35권2_spc호
• /
• pp.347-355
• /
• 2022

Among edible insects, black soldier fly (Hermetia illucens), yellow mealworm (Tenebrio molitor), and common housefly (Musca domestica) have been considered as an alternative protein source for pigs. Because they are easy to breed and grow in the organic wastes, and they have well-balanced nutritional value as a protein source for pigs. The black soldier fly larvae and mealworm could replace the fish meal in the diets for weaned pigs without adverse effects on growth performance and nutrient digestibility. Black soldier fly could also be included in the finishing pig's diet without any negative effects on the growth performance and pork quality of the market pigs. Insect products showed a greater standardized ileal digestibility value of amino acids than conventional animal proteins in growing pigs. Due to the limited amount of insect products used for pig feeding study, most previous pig studies have been conducted in weaned pigs. Thus, further study is needed about the optimal inclusion level of insect products in every phase diet from weaned pigs to sows. The use of insect products in swine diets has some challenges in terms of cost, supply, and safety. Lastly, intrinsic differences among insect species, processing method, and feeding phase should be taken into consideration for the use of insect products in the swine diets.