• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.397-400
• /
• 2000

The demands of high data transfer rate and high recording density in optical disk memory device are being increased. In order to achieve high performance, lever actuator for optical disk is proposed. Firstly, the role of lever and structure are discussed and the flexure hinge is introduced to enhance the precise movement. Next is to present the magnetic circuit structure and concept design for the lever actuator. Finally, the dynamic modeling of the lever actuator is found and the analysis results are shown. Consequently, the lever actuator shows the possibility as a pickup actuator for the next generation optical disk.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.618-621
• /
• 2001

The proposed lever actuator has no friction and mass balance characteristics in motion, which are adapt to high-speed and high-density optical disk system. This paper discussed about the theoretical analysis of the lever structure. The modeling of the lever actuator is found. Using the Newton's method, the motion of equation is deduced through the constraint equations and equilibrium equations in three directions (focusing, tracking and tilting). From the above analysis, we know that the shape of the hinge is the very important parameter on determining the performance of the lever actuator, and the actuator has the 2nd order system characteristics. And the first resonant frequency in transmissibility is dependent to the rigidity of the lever while the first transmissibility resonance of conventional actuators is dependent to the first natural resonance of those actuators. This means that the lever actuator is more stable to the external vibration.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.9
• /
• pp.41-50
• /
• 2002

Optical disk system aiming at fast data transfer rate and high-density recording requires the improvement in performance of the pickup head. Especially, the pickup actuator needs better linearity and stability. So, a lever actuator for optical disk is proposed. In this paper, the role of lever and its structure are discussed and the flexure hinge is introduced to enhance the precise movement. Using the Newoton's method, the motion of equation for the lever actuator is obtained. The results are compared with the analysis results by the FEM (Finite Element Method) for the vibration and the magnetic field. Consequently, the lever actuator has the 2"d system characteristics in 3-axis moving directions and superior stability for the external vibration.tion.

• Journal of the Optical Society of Korea
• /
• v.12 no.4
• /
• pp.303-308
• /
• 2008

Directly modulated fiber-optic links generally suffer higher link loss and larger signal distortion than externally modulated links. These result from the electron-photon conversion loss and laser modulation dynamics. As a method to overcome the drawbacks, we have experimentally demonstrated the RF performance of directly modulated, ultra-strong injection-locked gain-lever distributed Bragg reflector (DBR) lasers. The free-running DBR lasers exhibit an improved amplitude modulation efficiency of 12.4 dB under gain-lever modulation at the expense of linearity. By combining gain-lever modulation with ultra-strong optical injection locking, we can gain the benefits of both improved modulation efficiency from the gain-lever effect, plus improved linearity from injection locking. Using an injection ratio of R=11 dB, a 23.4-dB improvement in amplitude response and an 18-dB improvement in spurious-free dynamic range have been achieved.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.9
• /
• pp.961-964
• /
• 2012

This paper presents a sensing system to measure the deflection of a microcantilever in an atomic force microscope. In general, the optical lever method and interferometry are used for the sensing system; however, their size and cost leaves considerable room for improvement. Therefore, we used an optical pickup head whose operating principle is based on the astigmatism of the commercial optical disk drives. The developed sensing system was applied to a laboratory atomic force microscope, and satisfactory results were obtained.

• Journal of Sensor Science and Technology
• /
• v.20 no.1
• /
• pp.40-45
• /
• 2011

Microcantilevers have been actively used in probe-based microscopy and gravimetric sensing for biological or chemical analytes. To integrate actuation or detection schemes in the structure, typical fabrication processes include several photolithographic steps along with conventional MEMS fabrication. In this paper, a simple and straightforward way to fabricate and operate silicon microcantilever mass sensors is presented. The fabricated microcantilever sensors which can be electrostatically actuated require only two photolithographic steps. Resonant characteristics of fabricated microcantilevers are measured with a custom optical-lever and results show size-dependent quality factors. Using a $40\;{\mu}m$ long, $7\;{\mu}m$ wide, and $3\;{\mu}m$ thick cantilever, we achieved subfemtogram mass resolution in a 1 Hz bandwidth.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.4
• /
• pp.41-46
• /
• 2007

This article deals with the design and prototyping of Shift-By-Wire system for an automatic transmission equipped vehicle. In order to manipulate the shifting action electronically, Shift-By-Wire system consists of an electronic shift lever, an electric shift actuator and position sensors. The shift lever is designed to transform the driver's shifting command into an electric signal; it includes the position sensor using non-contact type hall sensor and an additional shifting switch acting as Tip-tronic. For the design of an electric shifting actuator, we investigated the stroke angles and shifting efforts of the manual control lever in each shifting section. And the position sensor of the shifting actuator is designed by using a potentiometer with an optical encoder. Finally the prototype of Shift-By-Wire system was built in a conventional 2.4L class SUV vehicle, and we performed road tests in order to verify its performance.

• Electronics and Telecommunications Trends
• /
• v.35 no.4
• /
• pp.42-52
• /
• 2020

The world's first 5G commercial service started in Korea in April 2019. This makes us proud of our status as an ICT powerhouse, and of the domestic optical network industry ecosystem that has served as a lever to make this significant leap forward in technological and industrial competitiveness. Above all, Japan's trade regulations on core parts and the COVID-19 pandemic have led to new changes across cultures, societies, and economies, and 5G networks have become important. The relevant technology for core material parts is a major concern not only of a few industries, but an entire section of society in terms of national competitiveness. In this article, we discuss the role of industries through the analysis of prospects of optical component technology with regard to the changes in the economic and social paradigm caused by the COVID-19 pandemic and Japan's export regulations.

• Proceedings of the Optical Society of Korea Conference
• /
• 2004.07a
• /
• pp.4-5
• /
• 2004

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.2
• /
• pp.35-44
• /
• 2009

Long stroke Fast Tool Servo (LFTS) with maximum stroke of $432{\mu}m$ is designed, manufactured and tested for fabrication of optical free-form surfaces. The large amount of stroke in LFTS has been realized by utilizing the hinge and lever mechanisms which enable the displacement amplification ratio of 4.3. In this mechanism the peculiar shape was devised for maximizing the displacement of end tip in LFTS and special mechanical spring has been mounted to provide the sufficient preload to the piezoelectric actuator. Also, its longitudinal motion of tool tip can be measured by capacitive type displacement sensor and closed-loop controlled to overcome the nonlinear hysteresis. In order to verify the static and dynamic characteristics of designed LFTS, several features including step response, frequency response and cut-off frequency in closed-loop mode were experimentally examined. Also, basic machining result shows that the proposed LFTS is capable of generating the optical free-form surface as an additional axis in diamond turning machine.