• Journal of the Korean Ceramic Society
• /
• v.56 no.1
• /
• pp.71-76
• /
• 2019

Monochromatic amber phosphor in glasses (PiGs) for automotive LED applications were fabricated with $YAG:Ce^{3+}$, $CaAlSiN_3:Eu^{2+}$ phosphors and Pb-free silicate glass. After synthesis and thickness-thinning process, PiGs were mounted on high-power blue LED to make monochromatic amber LEDs. PiGs were simple mixtures of 566 nm yellow YAG, 615 nm red $CaAlSiN_3:Eu^{2+}$ phosphor and transparent glass frit. The powders were uniaxially pressed and treated again through CIP (cold isostatic pressing) at 200 MPa for 20 min to increase packing density. After conventional thermal treatment at $550^{\circ}C$ for 30 min, PiGs were applied by using GPS (gas pressure sintering) to obtain a fully dense PiG plate. As the phosphor content increased, the density of the sintered body decreased and PiGs containing 30 wt% phosphor had full sintered density. Changes in photoluminescence spectra and color coordination were investigated by varying the ratio of $YAG/CaAlSiN_3$ and the thickness of the plates. Considering the optical spectrum and color coordinates, PiG plates with $240{\mu}m$ thickness showed a color purity of 98% and a wavelength of about 605 nm. Plates exhibit suitable optical characteristics as amber light-converting material for automotive LED applications.

• Korean Journal of Optics and Photonics
• /
• v.33 no.6
• /
• pp.287-294
• /
• 2022

This study presents a method for designing an athermal middle wavelength infrared (MWIR) zoom lens with the iterative selection of material compositions on an athermal glass map. The optical properties of glass for MWIR are generally very sensitive to temperature, compared with visible glass. To compensate for focus error due to temperature change, the non-athermalized zoom system requires a large amount of movement of a compensator, which results in an unstable zoom system. To solve this problem, the material compositions for an athermal zoom lens have effectively been obtained using the thermal aberration correction process analytically on an athermal glass map. An expander lens is used to enlarge the focal lengths of an original main zoom lens two times. Finally, while this expander is attached to an original athermal zoom system, the final zoom system equipped with this expander doubles the focal length ranges and has stable performance over a specified temperature range.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.254-257
• /
• 2001

An intensity-based optical fiber vibration sensor is applied to detect and evaluate damages and fiber failure of composites. The optical fiber vibration sensor is constructed by placing two cleaved fiber end, one of which is cantilevered in a hollow glass tube. The movement of the cantilevered section lags behind the rest of the sensor in response to an applied vibration and the amount of light coupled between the two fibers is thereby modulated. Vibration characteristics of the optical fiber vibration sensor are investigated. Surface mounted optical fiber vibration sensor is used in tensile and indentation test. Experimental results show that the optical fiber sensor can detect damages and fiber failure of composites correctly.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.547-552
• /
• 2001

An intensity-based optical fiber vibration sensor is applied to detect and evaluate damages and fiber failure of composites. The optical fiber vibration sensor is constructed by placing two cleaved fiber end, one of which is cantilevered in a hollow glass tube. The movement of the cantilevered section lags behind the rest of the sensor in response to an applied vibration and the amount of light coupled between the two fibers is thereby modulated. Vibration characteristics of the optical fiber vibration sensor are investigated. Surface mounted optical fiber vibration sensor is used in tensile and indentation test. Experimental results show that the optical fiber sensor can detect damages and fiber failure of composites correctly.

• Journal of the Optical Society of Korea
• /
• v.8 no.3
• /
• pp.127-131
• /
• 2004

This paper investigates applications of femtosecond lasers for the micromachining of transparent materials and fabrication of optical devices. We show commercial micromachining examples of transparent materials which have been fabricated for various applications. Near infrared femtosecond laser processing is an attractive method to fabricate three-dimensional optical waveguides into various transparent materials. Focused femtosecond laser pulses induce a permanent refractive-index change only near the focal point. We also demonstrate a Y coupler with the splitting ratio of 1:1 written by femtosecond laser pulses into a fused silica glass. The minimum propagation loss of 0.8 ㏈/㎝ awl the refractive-index change of 0.006-0.01 at the wavelength of 1550 ㎚ were achieved by optimization of the laser fluence.

• ETRI Journal
• /
• v.27 no.4
• /
• pp.446-448
• /
• 2005

Using tightly focused femtosecond laser pulses, we produce an optical waveguide and devices in transparent materials. This technique has the potential to generate not only channel waveguides, but also three-dimensional optical devices. In this paper, an optical splitter and U-grooves, which are used for fiber alignment, are simultaneously fabricated in a fused silica glass using near-IR femtosecond laser pulses. The fiber- aligned optical splitter has a low insertion loss, less than 4 dB, including an intrinsic splitting loss of 3 dB and excess loss due to the passive alignment of a single-mode fiber. Finally, we present an output field pattern, demonstrating that the splitting ratio of the optical splitter becomes approximately 1:1.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.3
• /
• pp.294-305
• /
• 1994

The influence of deposition parameter on the electrical, optical andsurface morphology of $SnO_2(:F)$ films prepared by ultrasonic spray deposition using DBDA and $SnCl_4.5H_2O$ as a source material was studied. Resistivity was decreased sharply with increasing F/Sn ratio in solution up to 0.6. Depending on the source material, $SnCl_4.5H_2O$ shows lower resistivity than DBDA. When F/Sn ratio in solution was 1, optical transmittance was higher DBDA than $SnCl_4.5H_2O$.

• Korean Journal of Optics and Photonics
• /
• v.11 no.3
• /
• pp.202-205
• /
• 2000

One step thermal potassium ion exchange process was carried out to form optical channel waveguides in an ErNb co-doped phosphate glass. Flowing oxygen gas into KN03 melt during ion exchange was effective to prevent glass surface damage that causes an increase of waveguide propagation loss. Amplification characteristics of the waveguides were evaluated at $1.5{\mu}m$ signal wavelength with 980 om laser diode pump. A 45 mm long waveguide whose processing parameters had been optimized exhibited a small signal net gain of 7.5 dB at the launched pump power of 160 mW.160 mW.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.5
• /
• pp.213-219
• /
• 2011

Recently aspheric lenses are widely used for superpricision optical instruments, such as cellular phone camera modules, digital cameras and optical communication modules. The aspherical lenses are processed using mold core under high temperature compressive forming pressure. It is imperative to develop superhard protective films for the life extension of lens forming mold core. Especially ta-C films with higher $sp^3$ fractions receive attentions for the life extension of lens forming mold and, in turn, the cost reduction of lenses due to their suprior high temperature stability, high hardness and smooth surfaces. In this study ta-C films were processed on WC mold as a function of substrate bias voltage using FVA (Filtered Vacuum Arc) method. The processed films were characterized by Raman spectroscopy and nano-indentation to investigate bonding nature and hardness, respectively. The film with maximun 87% of $sp^3$ fraction was obtained at the substrate bias voltage of -60 V, which was closest to ta-C film. ta-C films showed better high temperature stability by sustaining relatively high fraction of $sp^3$ bonding even after 2,000 glass lens forming applications.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.6
• /
• pp.252-258
• /
• 2001

($Ba_{0.7}Sr_{0.3})TiO_3$thin films were perpared on ITO-coated glass substrate by spin-coating method. The sol was sonicated in an ultrasonic bath to promote homogenization and the results were compared with untreated case. By application of the sonication process, crystallization temperatures of films were reduced, microstructers of films were more uniform and denser and the surface roughness of the films was lower from 8.4nm to 5.6nm. In addition, optical transmittances and electrical properties of films prepraed from sonicated sol were superior to those of films from untreated.