• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 춘계학술발표대회 논문집
• /
• pp.42-45
• /
• 2003

Optical fiber vibrations sensors (OFVSs) and extrinsic Fabry-Perot interferometer (EFPI) were used in damage monitoring of fiber-metal laminates(FML). The optical fiber vibration sensor and EFPI were applied in order to detect and evaluate the strain, damage and failure of FML. Damages in composites, such as matrix cracks, delamination and fiber breakage may occur as a result of excessive load, fatigue and low-velocity impacts. Indentation test was performed with the measurement of optical signal and acoustic emission (AE). The signals of the optical fiber vibration sensor due to damages were quantitatively evaluated by wavelet transform. It was found that damage information of comparable in quality to acoustic emission data could be obtained from the optical fiber vibration sensor signals.

• 산업기술연구
• /
• 제22권B호
• /
• pp.241-249
• /
• 2002

Optical fiber is indispensable for optical communication systems that transmit large volumes of data at high speed, but super precision technology in sub-micron units is required for optical axis adjustment. We developed the automatic optical fiber by image processing and automatic loading system. we have developed 6-axis micro stage system for I/O optical fiber arrays, the initial automatic aligning system software for a input optical array by the image processing technique, fast I/O-synchronous aligning strategy, the automatic loading/unloading system and the automatic UV bonding mechanism. In order to adjust the alignment it used on PC based motion controller, a $10{\mu}m$ repeat-detailed drawing of automatic loading system is developed by a primary line up for high detailed drawing. Also, at this researches used the image processing system and algorithm instead of the existing a primary hand-line up and fiber input array and waveguide chip formed in line by automatic.

• Journal of Electrical Engineering and Technology
• /
• 제1권4호
• /
• pp.546-549
• /
• 2006

In this paper the neuron operation based on Brillouin-active fiber in optical fiber is described. The inherent optical feedback by the backscattered stokes wave in optical fiber leads to instabilities in the form of optical chaos. Controlling of chaos induced transient instability in Brillouin-active fiber is implemented with Kerr nonlinearity having a non-instantaneous response in network systems. The controlling chaotic instabilities can lead to multistable periodic states; create optical logic 'on' or high level '1' or 'off', or low level '0'. It is theoretically possible to apply the multi-stability regimes as an optical memory device for encoding and decoding series and complex data transmission in optical systems.

• Journal of the Optical Society of Korea
• /
• 제13권1호
• /
• pp.33-36
• /
• 2009

Laser ablation with femtosecond lasers is highly promising for microfabrication of materials. Also, the high peak power of femtosecond lasers could induce a multiphoton absorption to ablate transparent materials. Similar results have also been were obtained in the case of optical fibers. In this paper, we present our experimental results of femtosecond laser microstructuring of optical fiber and its applications to microelectronic components and fiber optic devices. Finally, we directly produced micro holes with femtosecond laser pulses in a single step by moving an optical fiber in a preprogrammed structure. When water was introduced into a hole drilled from the bottom surface of the optical fiber, the effects of blocking and redeposition of ablated material were greatly reduced and the aspect ratio of the depth of the hole was increased. We have presented circular and rectangular-shaped holes in optical fiber.

• 대한기계학회논문집A
• /
• 제22권3호
• /
• pp.579-587
• /
• 1998

In this study, fatigue behavior of the optical fiber sensor embedded in composite laminate was investigated. Static tensile and fatigue tests were performed for three types of laminated composite specimens with embedded optical fiber sensor in the neutral plane ; [0/sub 6//OF/0/sub 6/]/sub T/, [0/sub 2//90/sub 4//OF/90/sub 4//0/sub 2/]/sub T/ and [0/sub 3//90/sub 3//OF/90/sub 3//0/sub 3/]/sub T/. The fracture of the embedded optical fiber sensor was detected by the intensity drop off of laser signal transmitted through the optical fiber sensors embedded within laminated composite specimen. The maximum fatigue stress applied to laminated specimen was compared with the average tensile stress at which the fracture of the embedded optical fiber within the laminate occurred under static tensile loading. From the experiments, firstly it is observed that the decrease in the life of optical fiber sensors embedded within unidirectional-ply laminate by the fatigue loading is relatively small compared to that of cross-ply laminate. Secondly, the optical fiber embedded in unidirectional-ply laminate is fractured by the fatigue damage due to the growth of internal defects of optical fiber, however the optical fiber embedded in cross-ply laminate is fractured by the growth of transverse matrix crack.

• Bulletin of the Korean Chemical Society
• /
• 제35권1호
• /
• pp.25-29
• /
• 2014

This research was aimed to fabricate an optical fiber-based SERS substrate which can detect dopamine neurotransmitters. Chitosan nanoparticles (NPs) were firstly anchored on the surface of optical fiber, and then gold layer was subsequently deposited on the anchored chitosan NPs via electroless plating method. Finally, chitosan-gold nanocomposites combined with optical fiber reacted with dopamine molecules of 100-1500 mg/day which is a standard daily dose for Parkinson's disease patients. The amplified Raman signal at $1348cm^{-1}$ obtained from optical fiber-based SERS substrate was plotted versus dopamine concentrations (1-10 mM), demonstrating an approximate linearity of Y = 303.03X + 2385.8 ($R^2$ = 0.97) with narrow margin errors. The optical fiber-based Raman system can be potentially applicable to in-vitro (or in-vivo) detection of probe molecules.

• 한국산학기술학회논문지
• /
• 제10권10호
• /
• pp.2691-2695
• /
• 2009

오늘날 광통신 시스템은 거의 무한대의 대역폭을 지니게 되었으며 이를 통하여 다양한 멀티미디어 데이터들을 신속하게 전송하는데 사용되고 있다. 이러한 광통신 시스템 하에서 텍스트, 이미지 및 동영상 등 다양한 멀티미디어 데이터들을 송수신 하기 위해서는 통합된 통신서비스시스템의 사용이 필수적이다. 본 논문에서는 멀티 비디오데이타와 오디오 데이타를 한가닥의 광통신 라인으로 주고받을 수 있도록 해주는 광 MVAD(Multi-Video Audio Data)쌍방향 다채널 링크시스템을 개발하였다. 개발된 광링크 시스템은 오직 하나의 광케이블을 사용하여 광통신시스템을 구축 할 수 있으며 우수한 영상과 음향을 공급하는 광섬유 매개체로 인하여 다양한 분야에 적용이 가능하다.

• Journal of the Optical Society of Korea
• /
• 제7권2호
• /
• pp.79-83
• /
• 2003

In this paper, we describe the fabrication process of a photonic crystal fiber and present the measured optical properties of the photonic crystal fiber. The fabrication of the photonic crystal fiber involves stacking, jacketing, collapsing, and drawing using a conventional drawing tower The photonic crystal fiber drawing needs higher tension to maintain the uniform air hole structure. Thus, the temperature of the photonic crystal fiber drawing is lowered by a few hundred degrees Celsius than for the case of conventional optical fiber drawing. The optical properties of the fabricated photonic crystal fiber such as mode profile, optical loss, transmission spectrum, bending loss, and polarization dependent loss are measured.

• 전자공학회논문지B
• /
• 제30B권5호
• /
• pp.34-42
• /
• 1993

Due to the low loss, broadband and accurate short time delay properties of optical fiber, it has attracted as a delay medium for high speed and broad-band signal processing. In this paper, we consider the coherent optical fiber filter of lattice structure, which uses coherent light sources and consists of directional couplers and optical fiber delay elements.The differences between the optical fiber filter and the ordinary digital filter are 1) the coupling coefficients of directional couplers are restricted between 0 and 1. 2) the optical signal is divided into ${j\sqrt{a}}and\;{j\sqrt{1-a}}$ at the directional coupler. Considering these restrictions, the design formulae and condition of realibility for optical fiber filter of lattice structure which makes the optimal use of optical signal energy are derived.

• 한국광학회지
• /
• 제28권4호
• /
• pp.135-140
• /
• 2017

본 논문에서는 고출력 광섬유 레이저를 위한 광섬유 칩 기반 all-fiber $7{\times}1$ 펌프 광 결합기의 제작에 대하여 보고한다. 광섬유 칩은 코어, 클래딩 직경이 각각 20, $400{\mu}m$인 광섬유를 길이 방향으로 식각하여 제작하였다. 7개의 입력 광섬유 부분은 105, $125{\mu}m$의 코어, 클래딩 직경을 가진 7개의 입력 광섬유를 원통형 다발로 제작하여 광섬유 칩의 $375{\mu}m$부분에 융착하였고, 1개의 출력 광섬유는 코어, 클래딩 직경이 각각 25, $250{\mu}m$ 광섬유를 광섬유 칩의 $250{\mu}m$부분에 융착하여 최종적으로 $7{\times}1$ 펌프광 결합기를 제작하였다. 제작된 광섬유 칩 기반 $7{\times}1$ 펌프 광 결합기의 포트별 평균 광 전달 효율은 약 90.2%로 나타났다.