• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.12
• /
• pp.1195-1200
• /
• 2007

Torque of a rotating shaft has been mostly measured by strain gages combined with either a slip ring or telemetry. However, these methods have severe inherent problems like low S/N ratio, high cost, limited number of channels and difficult installation. In this paper, a new method using FBG(fiber bragg grating) sensors and a rotary optical coupler for online non-contact torque monitoring is suggested. FBG sensor can measure both strain and temperature, and has much batter characteristics than those of a strain gage. A rotary optical coupler is a optical connecting device between a rotating shaft and stationary side without any physical contact. It has been devised for transmitting light between a rotating optical fiber and a stationary optical fiber. The proposed method uses this rotary optical coupler to connect FBG sensors on the rotating shaft to instruments at stationary side. And a reference FBG sensor is also applied to compensate the insertion loss change of the rotary optical coupler due to rotation. Three FBG sensors have been fabricated in a single optical fiber. Two FBG sensors are attached on the shaft surface to measure torque and one sensor is installed at the shaft center to compensate the insertion loss change. The torque of a rotating shaft has been successfully measured by the suggested method proving its superior performance potential.

• Proceedings of the Optical Society of Korea Conference
• /
• 1999.08a
• /
• pp.116-117
• /
• 1999

Optical fiber networks for microwave signal processing have been investigation . Theoretical and experimental results are presented in Z-shaped Double-Coupler Optical Resonator. The use of Mason's rule to calculate transfer functions greatly simplified the analysis in our model. A good comparison between modelling and experiment is presented.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.4
• /
• pp.62-72
• /
• 1997

The optical power splitter/couplers based on MMI(multimode interference) in GaAs/AlGaAs are studied. We presetn a design of optical power splitter/couplers, which have deeply etched multimode waveguide. The properties and fabrication tolerance on the etching depth, multimode waveguide width are simulatedusing a FD-BPM (finite difference beam propgation method). Proposed 1*N optical of designed device is 0.7dB smaller than the optical power splitter with a shallowly etched MMI section. For 0.5dB excess loss, the predicted fabrication tolerance is 0.6.mu.m on the multimode waveguide width of the 14 optical power splitter with a deeply etched MMI section. Also excess loss and uniformity of poposed 32*32 optical power coupler are below 0.3dB. The excess loss of proposed 32*32 optical power coupler is 2dB smaller than the optical power coupler with a shallowly etched MMI section. It is shown that the optical power splitters/couplers with a deeply etched mMI section have low loss, good uniformity, and improved fabriction tolerance.

• Journal of the Optical Society of Korea
• /
• v.12 no.4
• /
• pp.255-261
• /
• 2008

This paper reports a side-coupled asymmetric $1{\times}2$ plastic optical fiber coupler for an optical sensor system. The dependence of the optical power coupling ratio on the coupling angle and refractive index of the adhesion layer in both the forward and backward directions was examined based on the geometrical optics. It was confirmed experimentally that the coupling ratios can be optimized by controlling the coupling angle and refractive index of the adhesion layer. A maximum forward coupling efficiency > 93% was achieved.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.1
• /
• pp.77-82
• /
• 2008

Strain-gauges have been dominantly used to measure strain at various points on a rotor, however, either a slip ring or telemetry has to be used to send sensor signals to data acquisition instruments at stationary side. Both slip ring and telemetry have numerous inherent problems which force severe limitations in real applications. This paper introduces a new rotor condition monitoring system using FBG(Fiber Bragg Grating) sensors and a rotary optical coupler. A single optical fiber with many FBG sensors is installed on the rotor and an optical dynamic interrogator is installed at stationary side. The sensor signal connection between rotating part and stationary part is made by the rotary optical coupling method which makes use of light's unique characteristic-light travels through space. Broad band light source from the interrogator travels to the optical fiber on the rotor and reflected FBG sensor signals travel back to the optical fiber on stationary side and are connected to the interrogator. Rotary optical coupler's insertion loss change due to rotation is compensated by using a reference sensor installed at the center of the rotor. The proposed system's performance has been successfully demonstrated by accurately measuring strains at 5 points on a blade rotating at high speed.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.983-986
• /
• 1998

Inthis paper, we design 4$\times$4 optical star coupler with tapered coupling structure. The 4$\times$4 optical star coupler consists of four 3dB couplers and a 100% coupler with tapered structure. This star coupler is designed by the 2 dimension FD-BPM(finite difference beam propagation method) using TBC(transparent boundary condition). consequently, the maximum power unbalance ratios of relative output power from each of the output waveguides for each of input guides are less than 0.1dB, and the transmission efficiency is more than 99%.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.2 no.4
• /
• pp.5-16
• /
• 2003

We have analyzed the performance of optical matched filters in the fiber-optic code division multiple access (FO-CDMA) system based on optical parallel coupler access encoder (PCAE) and parallel coupler access decoder (PCAD) by experiment. In previous studies, the performance evaluation of the FO-CDMA system using SCAE and SCAD was not sufficiently accurate because they analyzed system performance only considering the first order signals. Since optical SCAE and SCAD intrinsically have high order signals of various patterns as the number of coupler increases, they change auto- and cross-correlation intensities. Thus, it is necessary to investigate properties of the PCAE and PCAD so that we may analyze the exact performance of system. In this paper, it is found that the peak to sidelobe ratio using the PCAE and PCAD increases as $\alpha$ (coupling coefficient) value increases. Also, we found that the proposed PCAE and PCAD are superior to SCAE and SCAD in performance improvement.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.6
• /
• pp.539-547
• /
• 1992

Considering the field of high frequency or broad-band signal filtering with high speed, we pro-pose optical fiber filters which consist of directional couplers and optical fiber delay elements. Fiber delay line signal processor Is operated with Incoherent optical carrier because of Its simplicity. Due to the characteristics of the directional coupler which Is basic element of optical fiber filter a new design method which Is different from that of usual digital filter is required. By considering the characteristics of directional coupler and in order to make good use of the optical signal energy, we have given the design formulae and the conditions of optical fiber filters for the direct and the lattice form.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.3
• /
• pp.505-512
• /
• 2019

We propose a new method to monitor the water level of spent fuel pool in a nuclear power plant without electric power. We also analyze the performance and limitation of the proposed method. Our method is based on the reflected optical power at the end of optical fiber through a $1{\times}N$ optical coupler. We reveal that there is no problem to monitor the water level when using a $1{\times}8$ optical coupler. However, when a $1{\times}16$ optical coupler is used, only 15 out of 16 output ports can be used due to Rayleigh back-scattering. When a $1{\times}32$ optical coupler is used, only 25 out of 32 output ports can be used to monitor the water level.

• Korean Journal of Optics and Photonics
• /
• v.6 no.4
• /
• pp.310-316
• /
• 1995

We designed the $1.3/1.55\mum$ WDM directional coupler and its coupling length was calculated with the variation of the two waveguide's core separation and other variables by the Fourier transformed scalar wave equation. We deposited the PSG films for optical waveguide by low pressure chemical vapor deposition and fabricated the WDM coupler using the laser lithography and $CF_4/O_2$ reactive ion etching process. A V -groove which was made to support and fix the optical fiber is fabricated on Si substrate by chemical etching. The WDM coupler and the V-groove are connected using UV curing epoxy. We found that propagation mode of each port of WDM coupler is single mode and maximum extinction ratio between two out ports is 6 dB for $1.3.\mum$, and 12 dB for $1.55\mum$. /TEX>.