• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.6
• /
• pp.462-465
• /
• 2019

Nanoscale gold particles have been intensively researched due to their potential applications in catalysis, electronics, plasmonics, and biological assays. In our study, we fabricated gold nanoparticles (NPs) that were synthesized in an aqueous environment via the reduction of $HAuCl_4$ by ascorbic acid (AC) with a sodium citrate (SC) surfactant. Highly monodispersed gold particles with sizes ranging from 123 to 184 nm were prepared in high-yield by a surfactant concentration. The structural and optical properties of the synthesized gold nanoparticles were characterized by transmission electron microscopy (TEM) and UV-vis spectroscopy. The prepared nanoparticles exhibited efficient surface-enhanced Raman scattering (SERS) properties that were dependent on their on size.

• Ceramist
• /
• v.10 no.3
• /
• pp.28-33
• /
• 2007

The structural and optical properties of Ni-doped transparent glass-ceramics are reviewed. The quantum efficiencies of ceramics were examined to explore suitable crystalline phase for Ni-doping in glass-ceramics. Inverse spinel $LiGa_5O_8$ have the quantum efficiency of almost 100 % at room temperature. Transparent glass ceramics containing $LiGa_5O_8$ was successfully synthesized by heat treatment of $Li_2O-Ga_2-O_3-SiO_2-NiO$ glass. Most of $Ni^{2+}$ ions in glass-ceramic were incorporated into $LiGa_5O_8$ nanocrystals. The near-infrared emission covering from the O-band to L-band (1260-1625 nm) was observed from the Ni-doped $Li_2O-Ga_2O_3-SiO_2$ glass-ceramic though it was not observed from the as-cast glass. The lifetime of the emission was about $580\;{\mu}sec$ even at 300K. The emission quantum efficiency was evaluated as about 10 % that is enough high for practical usage as gain media of optical fiber amplifiers. The figure of merit (the product of the stimulated emission cross section and lifetime) was as high as that of rare-earth-doped glasses. The broad bandwidth, high quantum efficiency and high figure of merit show that transparent glass-ceramics containing $Ni^{2+}:LiGa_5O_8$ nanocrystals are promising candidates as novel ultra-broadband gain media.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1402-1405
• /
• 2006

Using a indium zinc oxide (IZO) alloy target with a ratio of 90:10 in wt%, highly transparent conducting oxide (TCO) thin films are prepared on polyethersulfone (PES) substrates by lowfrequency (LF) magnetron sputtering system. These films have amorphous structures with excellent electrical stability, surface uniformity and high optical transmittance. Experiments were carried out as a function of applied voltage. At optimal deposition conditions, thin films of IZO with a sheet resistance of 29 ohm/sq. and an optical transmission of over 82 % in the visible spectrum range were achieved. The IZO thin films fabricated by this method do not require substrate heating during the film preparation or any additional post-deposition annealing treatment.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.534-537
• /
• 2019

The optical loss is caused by reflection on the surface of the solar cell, without being absorbed inside the solar cell. Research is actively being conducted to reduce optical loss due to such reflection of light and to improve conversion efficiency of solar cells. In this paper, the surface of the FTO glass substrate was wet etched, and the structural characteristics of the tough surface were evaluated. In addition, optical properties on the surface were analyzed, etched using spectrometer. When light was introduced to a rough surface formed by etching, it was confirmed that the multiple reflections reduced the amount of light reflection from the surface, thereby increaseing the amount of light penetrating the glass substrate.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.2
• /
• pp.93-96
• /
• 2017

The structural, electrical and optical properties of Ti thin films fabricated by dual magnetron sputtering were investigated under various film thicknesses. The fabricated Ti thin films exhibited uniform surfaces, crystallinity, various grain sizes, and with various film thicknesses. Also, the crystallinity and grain size of the Ti thin films increased with the increase of film thickness. The electrical properties of Ti thin films improved with the increase of film thickness. The results showed that the performance of TCO-less DSSC critically depended on the film thickness of the Ti working electrodes, due to the conductivity of Ti thin film. However, the maximum conversion efficiency of TCO-less DSSC was exhibited at the condition of 100 nm thickness due to the surface scattering of photons caused by the variation of grain size.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.8
• /
• pp.734-739
• /
• 2005

Zinc oxide films were deposited on Si (111) substrates by radio-frequency (rf)sputtering at a room temperature and post annealed in Na, air, and $H_2O$ ambient at temperatures between $800{\circ}C$ for 2 hrs. The properties were investigated by atomic force microscope (AFM), X-ray diffraction (XRD), Auger electron spectroscopy (AES) and photoluminescence (PL). Our experiments demonstrated that ZnO films have the better crystal quality for post thermal annealing and especially in $H_2O$ ambient. Even though thermal annealing reduced deep level emission somewhat, for further getting rid off deep level emission, oxygen contents should be adjusted. In our results, $H_2O$ ambient gave the best structural and optical properties.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1542-1545
• /
• 2005

Transparent conducting aluminum-doped zinc oxide (AZO) thin films have been deposited on corning 1737 glass by DC magnetron sputter. The structural, electrical and optical properties of the films were investigated as a function of various substrate temperatures. AZO thin films were fabricated by dc magnetron sputtering with AZO ceramic target $(Al_2O_3: 2wt %)$. The obtained films were poly crystalline with a hexagonal wurtzite structure and preferentially oriented in the (002) crystallographic direction. The lowest resistivity is $6.0{\times}10^{-4}$ Ocm with the carrier concentration of $2.694{\times}10^{20}\;cm^{-3}$ and Hall mobility of $20.426cm^2/Vs$. The average transmittance in the visible range was above 90%.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.7
• /
• pp.652-655
• /
• 2005

ZnO thin films on (001) $Al_2O_3$ substrates have been deposited by pulsed laser deposition(PLD) technique using an Nd:YAG laser with a wavelength of 266 nm. The influence of the deposition parameters, such as oxygen gas flow, substrate temperature and laser energy density variation on the properties of the grown film, was studied. The experiments were performed for substrate temperatures in the range of $300\~450^{\circ}C$ and oxygen gas flow rate of $100\~900$ sccm. We investigated the structural and optical properties of ZnO thin films using X-ray diffraction(XRD) and photoluminescence(PL).

• Applied Science and Convergence Technology
• /
• v.23 no.6
• /
• pp.387-391
• /
• 2014

Self-assembled InAlAs/AlGaAs quantum dots (QDs) on GaAs substrates were grown by using modified molecular epitaxy beam in Stranski-Krastanov method. In order to study the structural and optical properties of InAlAs/AlGaAs QDs, atomic force microscopy (AFM) and photoluminescence (PL) measurements are conducted. The size and uniformity of QDs have been observed from the AFM images. The average widths and heights of QDs are increased as the deposition time increases. The PL spectra of QDs are composed of two peaks. The PL spectra of QDs were analyzed by the excitation laser power- and temperature-dependent PL, in which two PL peaks are attributed to two predominant sizes of QDs.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.9
• /
• pp.495-501
• /
• 2000

This paper presents a method to minimize the initial deflection of a multi-layer piezoelectric microactuator without loosing its piezoelectric deflection performance required for light modulating micromirror devices. The multi-layer piezoelectric actuator composed of PZT silicon nitride and platinum layers deflects or buckles due to the gradient of residual stress. Based on the structural analysis results and relationship between process conditions and mechanical properties we have modified the fabrication process and the thickness of thin film layers to reduce the initial residual stress deflection without decreasing its piezoelectric deflection performance. The modified designs fabricated by surface-micromachining process achieved the 77% reduction of the initial deflection compared with that of the conventional method based on the measured micromechanical material properties is applicable to the design refinement of multi-layer MEMS devices and micromechanical structures.