• Journal of Surface Science and Engineering
• /
• v.38 no.5
• /
• pp.188-192
• /
• 2005

Indium zinc oxide (IZO) thin films were deposited on glass substrate by dc magnetron sputtering. The effects of oxygen flow rate and deposition temperature on electrical and optical properties of the films were investigated. With addition of small amount of oxygen gas, the characteristic properties of amorphous IZO films were improved and the specific resistivity was about $4.8{\times}10^{-4}\Omega{\cdot}cm$. Change of structural properties according to the deposition temperature was observed with XRD, SEM, and AFM. Films deposited above $300^{\circ}C$ were found to be polycrystalline. Surface roughness of the films was increased due to the formation of grains on the surface. Electrical conductivity became deteriorated for polycrystalline IZO films. Consequently, high quality IZO films could be prepared by do sputtering with $O_{2}/Ar{\simeq}0.03$ and deposition temperature in range of $150\~200^{\circ}C$; a specific resistivity of $3.4{\times}10^{-4}{\Omega}{\cdot}cm$, an optical transmission over $90\%$ at wavelength of 550 nm, and a rms value of surface roughness about $3{\AA}$.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1959-1961
• /
• 1999

We prepared the $Ag[100\AA])/Sb_2S_3[3000\AA]$ films using the thermal evaporator. The films were exposed by the blue-pass filtered mercury lamp and the polarized He-Ne laser. We have investigated the dependence of the induced optical energy with Ag-doping and have observed the transmittance variation near the optical absorption edge with the light source. It was shown that the energy gap of this thin film was largely changed by exposing He-Ne laser, the light source of the near energy gap of this thin film. It is because of the structural change from Ag-doping. It is investigated that the dissolution, the diffusion, and the field effect of the Ag thin film generate the Ag spatial distribution.

• Journal of the Korean Ceramic Society
• /
• v.33 no.12
• /
• pp.1365-1372
• /
• 1996

In order to obtain a transparent and dimer-free Ormosil embedded with orgainc dye variations of gel struc-ture and optical properties were studied as a functiion of the change of gel composition. The Ormosils which have good optical property were produced in the 90/10 ratio of TEOS/PDMS and the structural variations of the gel were achived by the change of ratio of HCl/TEOS. As the ratio of HCl/TEOS was increased pore size of the Ormosil enlarged and porosity increased. Increasing HCl concentration led to gradually lower trans-mittance values. In the xerogel doped with the organic dye Rhodamine 6G perchlorate a dimer peak near 500nm was observed with the increase of the ratio of HCl/TEOS

• Journal of Powder Materials
• /
• v.22 no.5
• /
• pp.309-314
• /
• 2015

Tungsten trioxide thin films are successfully synthesized by a sol-gel method using tungsten hexachloride as precursors. The structural, chemical, and optical properties of the prepared films are characterized by scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and UV-Vis spectrophotometry. The electrochemical and electrochromic properties of the films before and after heat treatment are also investigated by cyclic voltammetry, chronoamperometry, and in situ transmittance measurement system. Compared to as-prepared films, heat-treated tungsten trioxide thin films exhibit a higher electrochemical reversibility of 0.81 and superior coloration efficiency of $65.7cm^2/C$, which implies that heat treatment at an appropriate temperature is a crucial process in a sol-gel method for having a better electrochromic performance.

• Journal of Integrative Natural Science
• /
• v.1 no.3
• /
• pp.250-253
• /
• 2008

New issues arise as to surface characterization, quantification and interface formation. Surface and interface control of CdSe nanocrystal systems, one of the most studied and useful nanostructures. Semiconductor quantum dots (QDs) have been the subject of much interest for both fundamental reseach and technical applications in recent years, due mainly to their strong size dependent properties and excellent chemical processibility. In this dissertation, the synthesis of CdSe quantum dots were synthesized by pyrolysis of high-temperature organometallic reagents. In order to modify the size and quality of quantum dots, we controlled the growth temperature and the relative amount of precursors to be injected into the coordinating solvent. Moreover, an effective surface passivation of monodisperse nanocrystals was achieved by overcoating them with a higher-band-gap material. Synthesized CdSe quantum dots were studied to evaluate the optical, electronic and structural properties using UV-absorption, and photoluminescence measurement.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.167-167
• /
• 2010

Indium tin oxide (ITO) has been widely used as transparent conductive oxides (TCOs) for transparent electrodes of various optoelectronic devices, such as liquid crystal displays (LCD) and organic light emitting diodes (OLED). However, indium has become increasingly expensive and rare because of its limited resources. In addition, ITO thin films have some problems for OLED and flexible displays, such as imperfect work function, chemical instability, and high deposition temperature. Therefore, multi-component TCO materials have been reported as anode materials. Among the various materials, IZTO thin films have been gained much attention as anode materials due to their high work function, good conductivity, high transparency and low deposition temperature. IZTO thin films with a thickness of 200nm were deposited on Corning glass substrate at different substrate temperature by pulsed DC magnetron sputtering with a sintered ceramic target of IZTO (In2O3 70 wt%, ZnO 15 wt%, SnO2 15 wt%). We investigated the electrical, optical, structural properties of IZTO thin films. As the substrate temperature is increased, the electrical properties of IZTO are improved. All IZTO thin films have good optical properties, which showed an average of transmittance over 80%. These IZTO thin films were used to fabricate organic light emitting diodes (OLEDs) as anode and the device performances studied. As a result, IZTO has utility value of TCO electrode although it reduced indium and we expect it is possible for the IZTO to apply to flexible display due to the low processing temperature.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.4
• /
• pp.326-332
• /
• 2008

In this work CdS films were prepared by using chemical bath deposition, which is simple and inexpensive technique suitable for large deposition area. Annealing in air at different temperatures (300, 350, 400, 450 and $500^{\circ}C$) at constant time of 30 min, also for different times (15, 30, 45, 60 and 90 min) at constant temperature ($300^{\circ}C$) is achieved. X-Ray analysis has confirmed the formation of cadmium oxide (CdO) with slight increase in grain size, shift towards lower scattering angle due to relaxation in the tensile strain for deposition films, and structure change from cubic and hexagonal to the hexagonal. From electrical properties, significant increase in electrical conductivity appeared in samples annealed at $300^{\circ}C$ for 60 min, and at $350^{\circ}C$ for 30 min.

• Journal of the Korean Vacuum Society
• /
• v.19 no.3
• /
• pp.236-241
• /
• 2010

ZnO nanorods were grown on ZnO seed layer by hydrothermal method. The ZnO seed layer was coated by sol-gel method, and then the ZnO nanorods on ZnO seed layer were grown with different precursor concentrations ranging from 0.01 M to 0.3 M. FE-SEM (field-emission scanning electron microscopy), XRD (X-ray diffraction), and PL (photoluminescence) were employed to investigate the structural and optical properties of the ZnO nanorods. The diameter and length of ZnO nanorods are increased and also the optical properties are enhanced as the precursor concentrations are increased.

• Current Photovoltaic Research
• /
• v.4 no.3
• /
• pp.87-92
• /
• 2016

The effects of selenization pressure on the structural, optical and electrical properties of the CIGS thin films prepared by RF magnetron sputtering using a single quaternary target were investigated. At selenization pressures lower than atmospheric pressure, CIGS thin films formed non-stoichiometric compounds due to deficiencies of Se vapor. In contrast, when selenization process was conducted at above atmospheric pressure, the residence time of Se vapor inside the tube increased so that the Se element could be incorporated within vacant sites of the CIGS structure, resulting in the formation of stoichiometric CIGS thin films. High quality CIGS thin films could be obtained when the selenization process was performed at pressures greater than atmospheric and $550^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.2
• /
• pp.109-115
• /
• 2006

Indium tin oxide (ITO) films have been prepared by DC magnetron sputtering. In order to improve the utilization efficiency of the target and reduce the cost of the film deposition processes, the powder target was used instead of the conventional ceramic target. As-deposited films were annealed at temperatures between $200^{\circ}C$ and $500^{\circ}C$ for 30 min in air. Also, the film was annealed in various atmospheres such as air, $O_2,\;H_2,\;N_2$, and vacuum at $400^{\circ}C$C for 30 min. Effects of the heat treatment conditions on structural, electrical, and optical properties of ITO films were investigated. The annealing temperature of $400^{\circ}C$ and atmospheres of $H_2$ and $N_2$ seem to be the most suitable conditions for post processing.