• 한국전자통신학회논문지
• /
• 제15권1호
• /
• pp.39-44
• /
• 2020

유리기판위에 스퍼터링법으로 비정질 BaTiO₃막을 증착시켰다. 증착된 BaTiO₃ 막을 코로나 폴링을 하여 광학적 특성을 조사하였다. 가시광영역에서 투과율은 80% 이상으로 좋았으며, 비선형광학 특성은 폴링 조건에 따라 영향을 받으며, 크기는 1.15pm/V였다. 장기특성도 한달이 지나도 60%이상 유지하였다. 또한 BaTiO₃ 박막으로부터 녹색광 발생을 확인하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.477-479
• /
• 1997

The preparation of mach-zehnder inteferometric optical modulator and the properties of electrode and modulation bandwidth for high speed optical communications were described. The results of fabricated optical modulator was that optical 3-dB bandwidth 4.7GHz, driving voltage 6V and fiber-waveguide-fiber insertion loss 4.5dB for TM mode respectively.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.190-190
• /
• 2010

Zinc oxide is the most attractive material due to the large direct band gap (3.37 eV), excellent chemical and thermal stability, and large exciton binding energy (60 meV). Recently, ZnO nanorods were used as the high efficient antireflection coating layer of solar cells based on silicon (Si). In this reports, we studied the effects of rapid thermal annealing (RTA) treatment on optical properties of ZnO nanorods. For fabrication of ZnO nanorods, there are many methods such as hydrothermal method, sol-gel method, and metal organic chemical vapor deposition method. Among of them, we used the conventional wet chemical method which is simple and low temperature growth. In order to synthesize the ZnO nanorods, the ZnO films were deposited on Si substrate by RF magnetron sputtering at room temperature and the samples were dipped to aqua solution containing the zinc nitrate and hexamethylentetramines (HMT). The synthesis process was achieved in keeping with temperature of $90-95^{\circ}C$ and under constant stirring. The morphology of ZnO nanorods on glass and Si was characterized by scanning electron microscopy. For the analysis of antireflection performance, the reflectance and transmittance were measured by spectrophotometer. And for analyzing the effects of RTA treatment on ZnO nanorods, crystalline properties were investigated by X-ray diffraction measurements and optical properties was estimated by photoluminescence spectra.

• 한국전기전자재료학회논문지
• /
• 제31권3호
• /
• pp.171-176
• /
• 2018

An electronic paper display was fabricated by injecting electronic ink, including white and black particles coated by positive and negative charge control agents (CCA), respectively, into closed cells surrounded by micro-barriers. These two types of charged, colored particles are easily damaged or their charging value can be changed by the injection process; therefore, the electrical and optical properties of the image panel fabricated by the injection method were estimated in this study. The active particle-loading method, proposed as a new electronic ink injection process, was applied, and the electro-optical properties of the resulting three-electrode-type e-paper image panel were analyzed. The reflection rate of the white image-panel fabricated with our new injection method was 24.7%, while that of the same panel fabricated with a previously reported injection method was 19.8%. In addition, the response time was improved by about five times compared to those reported in other publications.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.109-110
• /
• 2005

Cadmium sulphide (CdS) films have been prepared on polycarbonate (PC), polyethylene terephthalate (PET), and Coming 7059 substrates by r.f. magnetron sputtering technique at room temperature. A comparison of the properties of the films deposited on polymer and glass substrates was performed. In addition, the influence of the sputter power on the structural and optical properties of these films was evaluated.

• 한국전기전자재료학회논문지
• /
• 제20권7호
• /
• pp.620-625
• /
• 2007

The effects of $Gd_2O_3$ addition and sintering condition on optical and electrical properties of MgO films as a protective layer for AC plasma display panels were investigated. Doped MgO films prepared by the e-beam evaporation have a higher ${\Upsilon}$ (secondary electron emission coefficient) than pure MgO protective layer. Relative density and grain size increased with amount of $Gd_2O_3$ up to 100 ppm and then decreased further addition. These results showed that discharge properties and optical properties of MgO protective layers seemed to be closely related with microstructure factors such as relative density and grain size. Good optical and electrical properties of ${\Upsilon}$ of 0.138, surface roughness of 5.77 nm and optical transmittance of 95.76 % were obtained for the MgO+100 ppm $Gd_2O_3$ protective layer sintered at $1700^{\circ}C$ for 5 hrs.

• Transactions on Electrical and Electronic Materials
• /
• 제2권1호
• /
• pp.22-26
• /
• 2001

ITO (Indium-tin-oxide) thin films were deposited on glass substrates by a dc magnetron sputtering system using ITO powder target. The methods of heat treatment are important factor to obtain high quality ITO films with low electrical resistivity and good optical transmittance. Therefore, both methods of the substrate temperature and post-deposition annealing temperature have been compared on the film structural, electrical and optical properties. A preferred orientations shifts from (411) to (222) peak at annealing temperature of 200$\^{C}$. Minimum resistivity of ITO film is approximately 8.7$\times$10$\^$-4/ Ωcm at substrate temperature of 450$\^{C}$. Optical transmittances at post annealing temperature above 200$\^{C}$ are 90%. As a result, the minimum value of annealing temperature that is required for the recrystallization of as-deposited ITo thin films is 200$\^{C}$.

• 한국전기전자재료학회논문지
• /
• 제22권9호
• /
• pp.760-765
• /
• 2009

The effects of $Fe_2O_3$ addition on optical and electrical properties of MgO films as a protective layer for AC plasma display panels were investigated. Doped MgO films prepared by the e-beam evaporation have a higher ${\gamma}$ (secondary electron emission coefficient) than pure MgO protective layer. Roughness increased with amount of $Fe_2O_3$ up to 100 ppm and then decreased further addition. These results showed that discharge properties and optical properties of MgO protective layers seemed to be closely related with microstructure factors such as roughness. Good optical and electrical properties of ${\gamma}$ of 0.120, surface roughness of 14.1 nm and optical transmittance of 94.55% were obtained for the MgO + 100 ppm $Fe_2O_3$ protective layer sintered at $1700^{\circ}C$ for 5 hrs.

• 한국전기전자재료학회논문지
• /
• 제21권4호
• /
• pp.376-380
• /
• 2008

The optical properties of multi layered thin films with $Sb_2O_3/Na_3AlF_6/Sb_2O_3/Cr$ were simulated by using EMP(Essential Macleod Program). EMP is a comprehensive software package to design and analyse the optical characteristics of multi-layered thin film. $Sb_2O_3$ and $Na_3AlF_6$ were selected as a high refractive index and low refractive index material respectively. Additionally Cr was chosen as mid reflective material. Optical properties including color effect were systematically studied in terms of different optical thickness of low refractive index material. The optical thickness of $Na_3AlF_6$ was changed as 0.25, 0.5, 0.75 and $1.0\lambda$. The film with 0.25, 0.5, 0.75 and $1.0\lambda$ of optical thickness showed mixed color range between purple and red range, yellowish green and bluish green, purple and mixed color range of green and purple respectively.

• 한국전기전자재료학회논문지
• /
• 제30권3호
• /
• pp.170-174
• /
• 2017

In 3 electrode reflective displays using a plastic substrate, unstable packaging induces particle clumping and optical degradation due to external air inflow and electronic ink evaporation. In this work, we fabricate 3 electrode electronic paper using glass wafer, ITO/plastic film, and ITO/glass/gas barrier film as an upper substrate after injecting electronic ink onto the lower substrate. Then, we studied its properties. After operating under stress conditions for 336 hours at $85^{\circ}C$ and 75% humidity, the reflectivity of driven e-paper panels with white color was 25.5% for the panels using glass wafer, 22.5% for plastic film including a gas barrier layer, and 16% for plastic film only. From these optical properties, we conclude that gas barrier film improves upper film isolation as a desirable packaging method.