• Journal of Sensor Science and Technology
• /
• v.30 no.6
• /
• pp.395-407
• /
• 2021

The effect of the specifications of a silicon-on-insulator vertical slot optical waveguide on the sensitivity of homogeneous and surface sensing configurations for TE and TM polarization, respectively, was systematically analyzed using numerical software. The specifications were optimized based on the confinement factor and transmission power of the TE-guided mode distributed in the slot. The waveguide sensitivities of homogeneous and surface sensing were calculated according to the specifications of the optimized slot optical waveguide.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.223-223
• /
• 2009

In this paper, designed and simulated Power Splitter (PS) integrated Mach-Zehnder interferometer (MZI) based planar type optical waveguide devices (which is called here a PS-MZI). The PS-MZI optical waveguide sensor was preceded by a Y-junction, which splits the input power between the sensor, and a reference branch, to minimize the effect of optical power variations. The PS-MZI optical waveguide sensor induced changing phases of the incident beam, which had fallen upon the waveguide through computer simulation, according to the small changes in the index of refraction, thus beam intensity was changed. The waveguide were optimized at a wavelength of 1550 nm and fabricated according to the design rule of 0.45 delta%, which is the difference of refractive index between the core and clad. The fabrication of PS-MZI optical waveguide sensor was performed by a conventional planar lightwave circuit (PLC) fabrication process. The PS-MZI optical waveguide that was fabricated to be applied as a biosensor revealed a low insertion loss and a low polarization-dependent loss. After having etched the over-clad at the sensor part in the MZI optical waveguide that was fabricated, Ti deposition was made on the adhesion layer, and then Au thin-film deposition was carried out thereon. In addition, its optical properties were measured by having changed the index of refraction oil at the sensing part of the MZI. To apply the planar type PS-MZI optical waveguide as a biosensor, a detection test for Staphylococcus aureus was conducted according to changes in concentration, having adopted Ti-alkoxide as ligand. The detection result of the S. aureus by the PS-MZI optical waveguide sensor was possible to the level of $10^1$ CFU/ml.

• The Journal of Korea Robotics Society
• /
• v.16 no.1
• /
• pp.1-11
• /
• 2021

Soft robotics has attracted a huge amount of interest in the recent decade or so, be it either actuators or sensors. Recently, a soft optical waveguide sensor has proven its effectiveness for various sensing applications such as strain, force, and bending measurements. The operation principle of the waveguide is simple, but the present technology is far too much complex to manufacture the waveguide. The waveguide fails to attract various practical applications in comparison to other types of sensors despite its superior safety and ease working principle. This study pursues to develop the soft sensors based on the optical phenomena so that the waveguide can be easily manufactured and its design can be conducted. Several physical properties of the waveguide are confirmed through the repetitive experiments in the aspects of strain, force, and bending of the waveguide. Finally, the waveguide sensor is embedded inside the actuator to verify the effectiveness of the proposed waveguide as well as to extend the application fields of the waveguide sensor.

• Electrical & Electronic Materials
• /
• v.9 no.3
• /
• pp.259-264
• /
• 1996

In this study, we performed a modeling for $K^{+}$ ion-exchanged diffused channel waveguide and waveguide-type optical coupler by Wentzel-Kramer-Brillouin(WKB) dispersion equation, normalized field distribution equation for mode and coupled mode theory, and examined the optical-power-dividing of the optical coupler fabricated by using the modeling condition. The optical-power-dividing was observed at the waveguide-type optical coupler with 3[.mu.m] line-width, 6[.mu.m] space between channel waveguides, and 3[mm] interaction length.h.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.7
• /
• pp.109-116
• /
• 1998

In this work was produced and analyzed a z-cut Ti:LiNbO$_{3}$ optical waveguide which applies for various optical devices.A waveguide channel with a thickness 8 .mu.m and a length 66,000.mu.m and a mach-zehnder interferometer type waveguide were fabricated at a diffusion temperature 1050.deg. C for 6-8hours in a wet $O_{2}$ environment. The resulting Ti:LiNbO$_{3}$ optical waveguide was measured to have a Ti-strip thickness of 950.angs. and low loss. Surfaces and cross-sections of a fabricated waveguide were analysed. The mode pattern anaysis revealed that the waveguide showed a single mode at a 1550nm wavelength. The effective dimension of the waveguide was calculated by measuring a gaussian profile; Wx=10.95.mu. and Wy=9.14.mu.m. a propagation loss, of 0.50dB/cm for a TM mode and 0.45dB/cm for a TE mode, was low enough to be accepatable for optical devices.

• Korean Journal of Optics and Photonics
• /
• v.7 no.3
• /
• pp.280-286
• /
• 1996

This paper describes operation mechanism of a novel optical waveguide phase modulator with optical bistability characteristics by self electro-optic effect. The fabricated device structure is an optical waveguide modulator, using a refractive index change by an applied electric field, parallel integrated with SEED with an electrical bistability. GaAs/AlGaAs MQW is used as the core layer of the waveguide modulator and the absorption layer of SEED. The absorbed optical power in SEED changes the diode voltage and controls the optical power propagating through the waveguide phase modulator. Optical bistability of waveguide phase modulator is experimentally obtained by using electrical bistability of SEED. Compared to other waveguide modulators, the proposed one has an asset that the lowest optical power is required to generate optical bistability.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.288-293
• /
• 2000

BPM simulation was used in order to fabricate the LiNbO$_3$optical waveguide with optical source of He-Ne laser(λ=0.6328[$\mu$m]). we observed electric field E$_{x}$, E$_{y}$ in the x,y-direction are simulated at the LiNbO$_3$substrate (X1 55[$\mu$m]$\times$Z1 5000[$\mu$m]), where the depth, width and buffer layer of waveguide are 0.2[$\mu$m],4[$\mu$m] and 0.02[$\mu$m] respectively. By applying these parameters of single waveguide to simulate a X-switch, we have chosen index change of 0.002, width of 3[$\mu$m] and angle of 0.4$^{\circ}$~0.6$^{\circ}$of optical waveguide and under these conditions, optical beam propagates cross-side at 0.4$^{\circ}$. When applied switching voltage of 25[V], optical beam of X-switch turns cross-side to bar-side at intersection angle 0.4$^{\circ}$, index change of 0.002, waveguide width of 3[$\mu$m], electrode gap 2[$\mu$m]. By the above results, we can obtain design conditions of theoretical analysis of an X-switch optical waveguide.e.e.

• Journal of the Optical Society of Korea
• /
• v.8 no.2
• /
• pp.90-95
• /
• 2004

The structure of Ti:LiNbO$_3$optical waveguide with a mode size far different from that of single mode optical fiber has been optimized by tapering the waveguide ends. This work was focused on determining the optimized sets of parameters for the fabrication of low-loss Ti indiffused optical waveguides in LiNbO$_3$. Numerical and analytical modeling were applied to simulate the guiding quality and to determine the mode sizes. Based on these modeling results, new waveguide structures with tapered ends have been defined, fabricated and characterized in the respect of the coupling of fiber to Ti-indiffused LiNbO$_3$waveguide.

• Journal of the Optical Society of Korea
• /
• v.15 no.4
• /
• pp.403-406
• /
• 2011

Here we report Airy beams coupled with waveguide modes. These waveguide Airy (WAiry) beams propagate through layered planar structures inheriting the characteristics of waveguide modes as well as those of Airy beams, such as diffraction-free and accelerating features. In particular, we focus on the WAiry beams associated with backward waveguide modes, showing that the backward feature can alter the trajectories of the WAiry beams significantly. Based on this, we propose a new scheme of waveguide-type polarization/power beam splitters.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.160-163
• /
• 2002

Silica waveguide for an integrated diffractive optical head system was designed and fabricated. The waveguide was designed to optimize the optical efficiency of red and/or blue laser source, and a lab-made RF magnetron sputter was adopted to deposit silica cladding and core layers on SiO$_2$/Si substrates. The cladding and core layers were formed using commercial targets, and the former was done with ＃7740 and the latter with BK7 and BAK4, respectively The surface roughness of the waveguide layers was measured to be 30.3${\AA}$ for BK7 and 17.8${\AA}$ for BAK4, and the difference of refractive indices between core and cladding layers was 0.9% and 2.5%, respectively. The waveguide fabricated with the core layer of BK7 showed better optical properties when the final diffractive optical probe heads were measured with red laser(650nm) source.