• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.185-192
• /
• 1989

It is shown that GaAs/GaAs stripe Roof-Top-Reflector LD is better than cleaved mirror LD by numerical analysis. And surface light emitting device is developed by LPE melt-back growth, which is of good controllability for OEIC. OEIC transmitter using RTR LD structured device and FET has been made and modulated, expected to show good modulation characteristics after solving process problem. Beam-Lead LD mounted on Si carrier has been made and shows low heat-resistance and so long life and good characteristics of LD.

• Polymer Science and Technology
• /
• v.21 no.1
• /
• pp.24-32
• /
• 2010

• ETRI Journal
• /
• v.36 no.3
• /
• pp.367-373
• /
• 2014

With high bandwidth, low interference, and low power consumption, optical network-on-chip (ONoC) has emerged as a highly efficient interconnection for the future generation of multicore system on chips. In this paper, we propose a new path-setup method for ONoC to mitigate contentions, such as packets, by recycling the setup packet halfway to the destination. A new, strictly non-blocking $6{\times}6$ optical router is designed to support the new method. The simulation results show the new path-setup method increases the throughput by 52.03%, 41.94%, and 36.47% under uniform, hotspot-I, and hotspot-II traffic patterns, respectively. The end-to-end delay performance is also improved.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.3
• /
• pp.239-243
• /
• 2003

In this paper, an angle diversity wireless optical detector is realized that can receive the optical signal at an angle from 0 to 360 degrees. Eight photodiodes constitute an angle diversity receiver, and in order to reduce the voltage variation with the incident angle, the optical detector is stabilized with a digital potentiometer. In a stabilized state, the voltage variation is kept within 1/10 of maximum voltage. This configuration is very useful in constructing an omni-directional receiver in a wireless optical interconnection.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.4
• /
• pp.336-342
• /
• 2003

In this paper, a new differential detector is introduced, in which a solar cell is used to reduce the low frequency interference from environmental optical noise. The solar cell also supplies electrical power to the detector circuit using the optical noise power. The DC voltage from the solar cell is used as a power supply to the detector, and the AC voltage is used to reduce the optical noise in a photodiode with the differential detection method. The signal to noise ratio was improved by about 20 dB.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.9
• /
• pp.2302-2311
• /
• 1998

The problem of scheduling general packet traffic on WDM optical interconnection networks is NP-complete, It is known that the list scheduling is a good approximation algurithm fur this problem, The resulting list schedules vary depending on the order of transmitters considered to be placed on each time slot We propose an improvement of the list scheduling that tries different orders of transmitters to obtain shorter schedule lengths, Genetic algorithms are used to explore various orders of transmitters.

• Proceedings of the IEEK Conference
• /
• 2001.06a
• /
• pp.155-158
• /
• 2001

A 640Gb/s high-speed ATM switching system that is based on the technologies of advanced MCM, 0.25um CMOS and optical WDM interconnection is fabricated for future N-ISDN services. A 40 layer, 160mm$\times$114mm ceramic MCM realizes the basic ATM switch module with 80Gbps throughput. The basic unit ATM switch module with 80Gb/s throughput. The basic unit ATM switch MCM consists of in 8 chip advanced 0.25um CMOS VLSI and 32 chip I/O Bipolar VLSIs. The MCM employs an 40 layer, very thin layer ceramic MCM and a uniquely structured closed loop type liquid colling system is adopted to cope with the MCM's high-power dissipation of 230w. The MCM is Mounted on a 32cm$\times$50cm mother board. A three stage ATM switch is realized by optical WDM interconnection between the high-performance MCM.

• Current Optics and Photonics
• /
• v.1 no.1
• /
• pp.7-11
• /
• 2017

In this study, multilayered graphene was easily transferred to the target substrate in one step using thermal release tape. The transmittance of the transferred graphene according to the number of layers was measured using a spectrophotometer. The sheet resistance was measured using a four-point probe system. Graphene formed using this transfer method showed almost the same electrical and optical properties as that formed using the conventional poly (methyl methacrylate) transfer method. This method is suitable for the mass production of graphene because of the short process time and easy large-area transfer. In addition, multilayered graphene can be transferred on various substrates without wetting problem using the one-step dry transfer method. In this work, this easy transfer method was used for dielectric substrates such as glass, paper and polyethylene terephthalate, and a sheet resistance of ~240 ohm/sq was obtained with three-layer graphene. By fabricating organic solar cells, we verified the feasibility of using this method for optoelectronic devices.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.2
• /
• pp.73-81
• /
• 2011

We manufactured the inkjet printing system for the application into the nano Ag finger line interconnection process in Si solar cells. The home-made inkjet printer consists of motion part for XY motion stage with optical table, head part, power and control part in the rack box with pump, and ink supply part for the connection of pump-tube-sub ink tanknozzle. The ink jet printing system has been used to conduct the interconnection process of finger lines on Si solar cell. The nano ink includes the 50 nm-diameter. Ag nano particles and the viscosity is 14.4 cP at $22^{\circ}C$. After processing of inkjet printing on the finger lines of Si solar cell, the nano particles were measured by scanning electron microscope. After the heat treatment at $850^{\circ}C$, the finger lines showed the smooth surface morphology without micropores.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.5
• /
• pp.82-88
• /
• 2007

This work is to fabricate a precise optical fiber array using polymer composite for optical interconnection. Optical fiber array has to satisfy low optical loss requirement less than 0.4 dB according to temperature change. For this purpose, design criteria for an optical fiber array was derived. The coefficient of thermal expansion of silica particulate epoxy composites was affected by volume fraction of silica particles. And also, elastic modulus of silica particulate epoxy composites was affected by volume fraction of silica particles. To obtain the coefficients of thermal expansion below $10{\times}10E-6/^{\circ}C$ and elastic modulus more than 20 GPa , we chose the volume fraction more than 76%. Using silica particulate epoxy composites with the volume fraction 76%, 8-channel optical fiber array with dimensional tolerances below $1\;{\mu}m$ was manufactured by transfer molding technique using dies with the uniquely-designed core pin and precisely-machined zirconia ceramic V block. These optical fiber arrays showed optical loss variations within 0.4 dB under thermal cycling test and high temperature test.